Eduard Pleshakov
Research Subjects
Eduard Pleshakov has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
M. M. Fetisova
4 shared publicationsLviv Polytechnic National University
2 shared publications- T. M. Kovbasyuk
Department of Materials Science and Engineering, Lviv Polytechnic National University, 12 S. Bandera Street, 79013 Lviv, Ukraine
2 shared publications T. P. Kovrova
2 shared publications- Volodymyr Volodymyrovych Kulyk
Department of Materials Science and Engineering, Lviv Polytechnic National University, 12 S. Bandera Street, 79013 Lviv, Ukraine
2 shared publications - Andrii Trostianchyn
Department of Materials Science and Engineering, Lviv Polytechnic National University, 12 S. Bandera Street, 79013 Lviv, Ukraine, Lviv Research Institute of Forensic Science, 54 Lypynskogo Street, 79024 Lviv, Ukraine
1 shared publication
Latest Publications
- 1 January 2022
- Published by Lviv Polytechnic National University in Ukrainian journal of mechanical engineering and materials science
- Vol. 8 (4) , 31-40
Causes of degradation of titanium dental implants
Corrosion is one of the main processes that cause problems when using metal implants in the environment of the human body. Due to its properties, titanium and its alloys are currently the most widely used biocompatible materials. But the use of implants made of titaniumbased alloys is not always successful. The purpose of our research was to establish the reasons for the rejection of a Swiss firm’s dental implant made of Grade 5 titanium alloy. Implanted in the patient’s jawbone, it worked as a support for an artificial tooth. But after 1 year of operation, inflammatory processes began at the implantation site, which ultimately led to rejection of the implant. To establish the material science reasons for this, we conducted microstructural studies using an electron microscope Zeiss EVO 40XVP. The sample was metallograpically prepared by grinding, polishing, and etching by using Kroll’s Reagent. A statistical image processing program was used to estimate the quantitative ratio of the phase components of the implant alloy Image J. Elemental analysis and mapping elements were also performed to know the compositional and distribution of each element Ti, Al and V by using energy dispersive X-Ray spectroscopy coupled in SEM. The hardness value was determined using Vickers microhardness tester. The conducted studies established that the working surface of the implant suffered corrosion damage during operation. The edges of the implant are uneven with open and closed pitting. In some places, the merging of several pittings is observed, which leads to the occurrence of ulcerative corrosion. Elemental analysis established the redistribution of chemical elements in the surface layers as a result of contact with the biological environment of the human body. Unstable compounds are created on the surface, which dissolves in the human body during use. As it follows from the conducted studies, the degraded surface of the dental implant needs additional protection.
- 1 January 2022
- Published by Lviv Polytechnic National University in Ukrainian journal of mechanical engineering and materials science
- Vol. 8 (4) , 31-40
Causes of degradation of titanium dental implants
Corrosion is one of the main processes that cause problems when using metal implants in the environment of the human body. Due to its properties, titanium and its alloys are currently the most widely used biocompatible materials. But the use of implants made of titaniumbased alloys is not always successful. The purpose of our research was to establish the reasons for the rejection of a Swiss firm’s dental implant made of Grade 5 titanium alloy. Implanted in the patient’s jawbone, it worked as a support for an artificial tooth. But after 1 year of operation, inflammatory processes began at the implantation site, which ultimately led to rejection of the implant. To establish the material science reasons for this, we conducted microstructural studies using an electron microscope Zeiss EVO 40XVP. The sample was metallograpically prepared by grinding, polishing, and etching by using Kroll’s Reagent. A statistical image processing program was used to estimate the quantitative ratio of the phase components of the implant alloy Image J. Elemental analysis and mapping elements were also performed to know the compositional and distribution of each element Ti, Al and V by using energy dispersive X-Ray spectroscopy coupled in SEM. The hardness value was determined using Vickers microhardness tester. The conducted studies established that the working surface of the implant suffered corrosion damage during operation. The edges of the implant are uneven with open and closed pitting. In some places, the merging of several pittings is observed, which leads to the occurrence of ulcerative corrosion. Elemental analysis established the redistribution of chemical elements in the surface layers as a result of contact with the biological environment of the human body. Unstable compounds are created on the surface, which dissolves in the human body during use. As it follows from the conducted studies, the degraded surface of the dental implant needs additional protection.
- 1 January 2020
- Published by Lviv Polytechnic National University in Ukrainian journal of mechanical engineering and materials science
- Vol. 6 (3-4) , 35-40
Influence of heat treatment modes on the performance characteristics of resistive cermet coatings
Dielectric and resistive coatings based on glass ceramics with nickel boride additives have been synthesized. It was found that the microstructure of the resistive coating consists of a large number of phases. X-ray fluorescence analysis revealed the presence of Ni and Cr borides in the structure of the resistive layer. It was found that the change in the structure and specific surface resistance of resistive pastes practically does not affect the temperature coefficient of resistance of the synthesized resistive tracks.
- 1 January 2020
- Published by Lviv Polytechnic National University in Ukrainian journal of mechanical engineering and materials science
- Vol. 6 (3-4) , 35-40
Influence of heat treatment modes on the performance characteristics of resistive cermet coatings
Dielectric and resistive coatings based on glass ceramics with nickel boride additives have been synthesized. It was found that the microstructure of the resistive coating consists of a large number of phases. X-ray fluorescence analysis revealed the presence of Ni and Cr borides in the structure of the resistive layer. It was found that the change in the structure and specific surface resistance of resistive pastes practically does not affect the temperature coefficient of resistance of the synthesized resistive tracks.
- 1 January 2020
- Published by Lviv Polytechnic National University in Ukrainian journal of mechanical engineering and materials science
- Vol. 6 (1) , 72-82
Failure analysis of a motor vehicle suspension helical spring
The purpose of this work is to reveal the cause of the failure of the motor vehicle rear suspension barrel-shaped spring with the progressive elasticity characteristic and predict measures to increase the lifetime of springs of this type. The fracture of the spring occurred on the middle coil, which operates under conditions of more severe stress in comparison with other coils. The chemical composition of the spring material, determined by X-ray fluorescence spectral and microstructural analyzes, corresponded to chromium-silicon steel 54SiCr6. In terms of structure and mechanical properties, the spring material met the standards. No traces of decarburization were detected, and no crack initiation, caused by non-metallic inclusions, was found in the material of the fractured spring. Macroscopic examination of the spring surface did not reveal any cracks, scratches, dents, traces of blows with stones and marks of spring coiling tool. Instead, extensive areas of exfoliation of the protective coating were found. The metallographic analysis revealed selective corrosion in the form of pitting damage in places of exfoliation of the protective coating. The fatigue crack propagates from the certain deep pit with the reorientation of the crack plane along the spiral surface to the central axis of the coil wire. After depletion of the safety margin, the spring broke down quickly. The fast fracture zone contains steps of the river pattern formed due to the spiral reorientation of the fracture surface. The research can be used to understand the importance of adhesive strength and wear resistance of protective coatings on the spring surface. Their local exfoliation causes subsequent corrosion damage to the spring, which stimulates its fatigue fracture.
- 1 January 2020
- Published by Lviv Polytechnic National University in Ukrainian journal of mechanical engineering and materials science
- Vol. 6 (1) , 72-82
Failure analysis of a motor vehicle suspension helical spring
The purpose of this work is to reveal the cause of the failure of the motor vehicle rear suspension barrel-shaped spring with the progressive elasticity characteristic and predict measures to increase the lifetime of springs of this type. The fracture of the spring occurred on the middle coil, which operates under conditions of more severe stress in comparison with other coils. The chemical composition of the spring material, determined by X-ray fluorescence spectral and microstructural analyzes, corresponded to chromium-silicon steel 54SiCr6. In terms of structure and mechanical properties, the spring material met the standards. No traces of decarburization were detected, and no crack initiation, caused by non-metallic inclusions, was found in the material of the fractured spring. Macroscopic examination of the spring surface did not reveal any cracks, scratches, dents, traces of blows with stones and marks of spring coiling tool. Instead, extensive areas of exfoliation of the protective coating were found. The metallographic analysis revealed selective corrosion in the form of pitting damage in places of exfoliation of the protective coating. The fatigue crack propagates from the certain deep pit with the reorientation of the crack plane along the spiral surface to the central axis of the coil wire. After depletion of the safety margin, the spring broke down quickly. The fast fracture zone contains steps of the river pattern formed due to the spiral reorientation of the fracture surface. The research can be used to understand the importance of adhesive strength and wear resistance of protective coatings on the spring surface. Their local exfoliation causes subsequent corrosion damage to the spring, which stimulates its fatigue fracture.
- 1 March 2019
- Published by Springer Nature in Powder Metallurgy and Metal Ceramics
- Vol. 57 (11-12) , 697-702
The Effect of Morphology and Particle-Size Distribution of VT20 Titanium Alloy Powders on the Mechanical Properties of Deposited Coatings
- 1 March 2019
- Published by Springer Nature in Powder Metallurgy and Metal Ceramics
- Vol. 57 (11-12) , 697-702
The Effect of Morphology and Particle-Size Distribution of VT20 Titanium Alloy Powders on the Mechanical Properties of Deposited Coatings
- 1 September 2002
- Published by Springer Nature in Materials Science
- Vol. 38 (5) , 646-652
Laser Surface Modification of Ti-6Al-4V Alloy with Silicon Carbide
- 1 September 2002
- Published by Springer Nature in Materials Science
- Vol. 38 (5) , 646-652
Laser Surface Modification of Ti-6Al-4V Alloy with Silicon Carbide
- 1 May 1983
- Published by Springer Nature in Metal Science and Heat Treatment
- Vol. 25 (5) , 361-362
Heat treatment of structural steels to reduce temper brittleness
- 1 May 1983
- Published by Springer Nature in Metal Science and Heat Treatment
- Vol. 25 (5) , 361-362
Heat treatment of structural steels to reduce temper brittleness
- 1 January 1979
- Published by Springer Nature in Materials Science
- Vol. 15 (3) , 302-303
Influence of austenitization temperature on the micromechanism of failure of structural steels in the temper brittleness condition
- 1 January 1979
- Published by Springer Nature in Materials Science
- Vol. 15 (3) , 302-303
Influence of austenitization temperature on the micromechanism of failure of structural steels in the temper brittleness condition
- 1 January 1976
- Published by Springer Nature in Materials Science
- Vol. 11 (3) , 309-311
Mechanism underlying the reduction in the strength of an intergranular bond during the development of reversible temper embrittlement in steels
- 1 January 1976
- Published by Springer Nature in Materials Science
- Vol. 11 (3) , 309-311
Mechanism underlying the reduction in the strength of an intergranular bond during the development of reversible temper embrittlement in steels
- 1 January 1974
- Published by Springer Nature in Materials Science
- Vol. 8 (4) , 471-473
Character of failure of carbon steels in the case of temper brittleness
- 1 January 1974
- Published by Springer Nature in Materials Science
- Vol. 8 (4) , 471-473
Character of failure of carbon steels in the case of temper brittleness