Yuhui Ma
Yuhui Ma has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
Junrui Cao
Research Team for Environmental Functional Materials Department of Environmental Technology The Institute of Seawater Desalination and Multipurpose Utilization Ministry of Natural Resources (MNR) Tianjin 300192 P. R. China
10 shared publicationsXunliang Wang
Research Team for Environmental Functional Materials, Department of Environmental Technology, The Institute of Seawater Desalination and Multipurpose Utilization (ISDMU), Ministry of Natural Resources of the People’s Republic of China, Tianjin, China
6 shared publicationsHanxin Huo
Technical Centre for Soil, Agriculture and Rural Ecology and Environment, Ministry of Ecology and Environment of the People’s Republic of China, Beijing, China
4 shared publicationsTianxiang Jiang
Research Team for Environmental Functional Materials, Department of Environmental Technology, The Institute of Seawater Desalination and Multipurpose Utilization (ISDMU), Ministry of Natural Resources of the People’s Republic of China, Tianjin, China
4 shared publicationsJing Wang
State Oceanic Administration (SOA)
3 shared publicationsYan Gao
School of Pharmaceutical Science and Technology, Tianjin University, Tianjin, China
3 shared publications
Latest Publications
- Open Access
- 30 December 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 31 (6) , 9867
Correction to: Magnetic activated carbon from spent coffee grounds: iron-catalyzed CO2 activation mechanism and adsorption of antibiotic lomefloxacin from aqueous medium
- 30 December 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 31 (6) , 9867
Open AccessCorrection to: Magnetic activated carbon from spent coffee grounds: iron-catalyzed CO2 activation mechanism and adsorption of antibiotic lomefloxacin from aqueous medium
- 15 December 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 31 (3) , 4140-4153
Magnetic activated carbon from spent coffee grounds: iron-catalyzed CO2 activation mechanism and adsorption of antibiotic lomefloxacin from aqueous medium
The facile fabrication of low-cost adsorbents possessing high removal efficiency and convenient separation property is an urgent need for water treatment. Herein, magnetic activated carbon was synthesized from spent coffee grounds (SCG) by Fe-catalyzed CO2 activation at 800 °C for 90 min, and magnetization and pore formation were simultaneously achieved during heat treatment. The sample was characterized by N2 adsorption–desorption, XRD, VSM, SEM, and FTIR. Batch adsorption experiments were conducted using lomefloxacin (LMO) as the probing pollutant. Preparation mechanism was revealed by TG-FTIR and XRD. Experimental results showed that Fe3O4 derived from Fe species can be reduced to Fe by carbon at high temperatures, followed by subsequent reoxidation to Fe3O4 by CO2, and the redox cycle between Fe and Fe3O4 favored the formation of pores. The promotion effects of Fe species on CO2 activation can be quantitatively reflected by the yield of CO as the signature gaseous product, and the suitable activation temperate range was determined to be 675 to 985 °C. The BET surface area, total pore volume, and saturated magnetization value of the product were 586 m2 g−1, 0.327 cm3 g−1, and 11.59 emu g−1, respectively. The Langmuir model was applicable for the adsorption isotherm data for LMO with the maximum adsorption capacity of 95 mg g−1, and thermodynamic analysis revealed that the adsorption process was endothermic and spontaneous. This study demonstrated that Fe-catalyzed CO2 activation was an effective method of converting SCG into magnetic separable adsorbent for LMO removal from aqueous medium.
- 15 December 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 31 (3) , 4140-4153
Magnetic activated carbon from spent coffee grounds: iron-catalyzed CO2 activation mechanism and adsorption of antibiotic lomefloxacin from aqueous medium
The facile fabrication of low-cost adsorbents possessing high removal efficiency and convenient separation property is an urgent need for water treatment. Herein, magnetic activated carbon was synthesized from spent coffee grounds (SCG) by Fe-catalyzed CO2 activation at 800 °C for 90 min, and magnetization and pore formation were simultaneously achieved during heat treatment. The sample was characterized by N2 adsorption–desorption, XRD, VSM, SEM, and FTIR. Batch adsorption experiments were conducted using lomefloxacin (LMO) as the probing pollutant. Preparation mechanism was revealed by TG-FTIR and XRD. Experimental results showed that Fe3O4 derived from Fe species can be reduced to Fe by carbon at high temperatures, followed by subsequent reoxidation to Fe3O4 by CO2, and the redox cycle between Fe and Fe3O4 favored the formation of pores. The promotion effects of Fe species on CO2 activation can be quantitatively reflected by the yield of CO as the signature gaseous product, and the suitable activation temperate range was determined to be 675 to 985 °C. The BET surface area, total pore volume, and saturated magnetization value of the product were 586 m2 g−1, 0.327 cm3 g−1, and 11.59 emu g−1, respectively. The Langmuir model was applicable for the adsorption isotherm data for LMO with the maximum adsorption capacity of 95 mg g−1, and thermodynamic analysis revealed that the adsorption process was endothermic and spontaneous. This study demonstrated that Fe-catalyzed CO2 activation was an effective method of converting SCG into magnetic separable adsorbent for LMO removal from aqueous medium.
- 14 April 2023
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 14 (16) , 19563-19580
Activated carbon from chili straw: K2CO3 activation mechanism, adsorption of dyes, and thermal regeneration
- 14 April 2023
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 14 (16) , 19563-19580
Activated carbon from chili straw: K2CO3 activation mechanism, adsorption of dyes, and thermal regeneration
- 21 February 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 33 (20)
Steering Electron Density of Zr Sites Using Ligand Effect in Bio‐Beads for Efficient Defluoridation
Because of spontaneous agglomeration effect and undesirable electronic state of Zr sites on the surface, zirconium (hydro)oxides generally exhibit suboptimal defluoridation capacity. Herein, a template confinement‐ligand anchoring strategy is developed by utilizing confined growth of zirconium hydroxide (ZH) inside chitosan hydrogel beads (CHB) and subsequent anchoring of fumaric acid (fm) on its surface Zr sites in a monodentate mononuclear coordination mode. This technique leads to uniform dispersion of ultrafine fmZH (≈3.4 nm) and tunable electron density at the Zr sites. Due to the electron‐withdrawing ability of fm, electron‐delocalized Zr sites increase the orbital energy level matching and vacate Zr 4d orbitals to promote hybridization with the F 2p orbitals. Ultimately, robust ZrF bond can be formed as a result of reduced the adsorption energy toward fluoride ions. The defluoridation capacity shows positive linear relationship with the electron extraction ability of ligands. The saturation adsorption capacity and dynamic treatment capacity of CHB@fmZH are 10.8 and 45.9 times higher than that of CHB@ZH, respectively, owing to high electron extraction (0.098 e−) of fm. This study offers a novel insight into the design and synthesis of high‐efficiency metal oxide adsorbents by steering its surface metal sites’ electronic state through ligand effect.
- 21 February 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 33 (20)
Steering Electron Density of Zr Sites Using Ligand Effect in Bio‐Beads for Efficient Defluoridation
Because of spontaneous agglomeration effect and undesirable electronic state of Zr sites on the surface, zirconium (hydro)oxides generally exhibit suboptimal defluoridation capacity. Herein, a template confinement‐ligand anchoring strategy is developed by utilizing confined growth of zirconium hydroxide (ZH) inside chitosan hydrogel beads (CHB) and subsequent anchoring of fumaric acid (fm) on its surface Zr sites in a monodentate mononuclear coordination mode. This technique leads to uniform dispersion of ultrafine fmZH (≈3.4 nm) and tunable electron density at the Zr sites. Due to the electron‐withdrawing ability of fm, electron‐delocalized Zr sites increase the orbital energy level matching and vacate Zr 4d orbitals to promote hybridization with the F 2p orbitals. Ultimately, robust ZrF bond can be formed as a result of reduced the adsorption energy toward fluoride ions. The defluoridation capacity shows positive linear relationship with the electron extraction ability of ligands. The saturation adsorption capacity and dynamic treatment capacity of CHB@fmZH are 10.8 and 45.9 times higher than that of CHB@ZH, respectively, owing to high electron extraction (0.098 e−) of fm. This study offers a novel insight into the design and synthesis of high‐efficiency metal oxide adsorbents by steering its surface metal sites’ electronic state through ligand effect.
- 13 June 2022
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 14 (7) , 8877-8894
Bio-inspired hierarchical porous activated carbon aerogel from waste corrugated cardboard for adsorption of oxytetracycline from water
- 13 June 2022
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 14 (7) , 8877-8894
Bio-inspired hierarchical porous activated carbon aerogel from waste corrugated cardboard for adsorption of oxytetracycline from water
- 17 May 2022
- Published by Springer Nature in Korean Journal of Chemical Engineering
- Vol. 39 (7) , 1775-1787
Carbon aerogel from waste corrugated cardboard: Facile preparation, characterization, and application to solar steam generation and adsorption
- 17 May 2022
- Published by Springer Nature in Korean Journal of Chemical Engineering
- Vol. 39 (7) , 1775-1787
Carbon aerogel from waste corrugated cardboard: Facile preparation, characterization, and application to solar steam generation and adsorption
- 24 November 2021
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 29 (16) , 23936-23948
3D carbon aerogel from waste corrugated cardboard as a photothermal reservoir for solar steam generation
Three-dimensional carbon aerogel (CA800) was prepared from waste corrugated cardboard (WCC) by the procedure of slurrying, solvent replacement, drying, and carbonization in turn, and the product was explored as an all-in-one evaporator for solar steam generation without bulk water. Carbonization of the precursor was investigated using thermogravimetric analyzer coupled with Fourier transform infrared spectrometer. Results showed that CO2, CO, furfural, and levoglucosan were released during pyrolysis of WCC within the range of 300 to 390 °C, while polymerization of newly formed char between 390 and 580 °C mainly resulted in the formation of CO2 and CO. Both pyrolysis and polymerization reactions can be described by diffusion-controlled mechanisms, and the activation energies were 155.62 and 11.17 kJ mol−1, respectively. CA800 possessed a BET surface area of 210 m2 g−1. Light can be effectively absorbed and converted into heat by CA800, and its surface temperature achieving 73 °C under 1 kW m−2 irradiation. CA800 had outstanding wettability due to the presence of hydrophilic minerals in carbon matrix, and it was able to store as much as 15 times its own weight in water due to its abundant interconnected channels and hierarchical nanopores. Solar-driven water evaporation rate over CA800 achieved 1.72 kg m−2 (normalized to projection area), which was nearly 6 times higher than the value achieved by the bare water system. The photothermal conversion efficiency was calculated to be 118 %, and the overestimated efficiency was caused by the environmental energy gained by the cold evaporation surface of CA800.
- 24 November 2021
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 29 (16) , 23936-23948
3D carbon aerogel from waste corrugated cardboard as a photothermal reservoir for solar steam generation
Three-dimensional carbon aerogel (CA800) was prepared from waste corrugated cardboard (WCC) by the procedure of slurrying, solvent replacement, drying, and carbonization in turn, and the product was explored as an all-in-one evaporator for solar steam generation without bulk water. Carbonization of the precursor was investigated using thermogravimetric analyzer coupled with Fourier transform infrared spectrometer. Results showed that CO2, CO, furfural, and levoglucosan were released during pyrolysis of WCC within the range of 300 to 390 °C, while polymerization of newly formed char between 390 and 580 °C mainly resulted in the formation of CO2 and CO. Both pyrolysis and polymerization reactions can be described by diffusion-controlled mechanisms, and the activation energies were 155.62 and 11.17 kJ mol−1, respectively. CA800 possessed a BET surface area of 210 m2 g−1. Light can be effectively absorbed and converted into heat by CA800, and its surface temperature achieving 73 °C under 1 kW m−2 irradiation. CA800 had outstanding wettability due to the presence of hydrophilic minerals in carbon matrix, and it was able to store as much as 15 times its own weight in water due to its abundant interconnected channels and hierarchical nanopores. Solar-driven water evaporation rate over CA800 achieved 1.72 kg m−2 (normalized to projection area), which was nearly 6 times higher than the value achieved by the bare water system. The photothermal conversion efficiency was calculated to be 118 %, and the overestimated efficiency was caused by the environmental energy gained by the cold evaporation surface of CA800.
- 19 February 2021
- Published by Wiley in ChemistrySelect
- Vol. 6 (8) , 1814-1822
Recovery of Aluminum and Preparation of Porous Carbon from Tetra Pak Waste
Pyrolysis of paper and polyethylene in Tetra Pak waste occurred at 368 and 490 °C, respectively, while aluminum did not melted until the temperature reached 660 °C, thus aluminum and char can be obtained by carbonization of Tetra Pak waste at 550 °C. Pyrolytic char was processed into porous carbons by different methods. Specific surface area of the porous carbon prepared by carbonization of acid‐washed char at 850 °C achieved 741 m 2 g −1 , and the specific surface area of the porous carbon prepared from char by successively carbonization at 850 °C and acid‐washing was 732 m 2 g −1 . The developed porous structure was formed due to the polymerization of char above 650 °C, while the etching of char by CO 2 generated via decomposition of inherent calcite led to a lower microporosity. Methylene blue adsorption capacity of the optimized sample reached 140 mg g −1 , and the equilibrium data followed Langmuir model.
- 19 February 2021
- Published by Wiley in ChemistrySelect
- Vol. 6 (8) , 1814-1822
Recovery of Aluminum and Preparation of Porous Carbon from Tetra Pak Waste
Pyrolysis of paper and polyethylene in Tetra Pak waste occurred at 368 and 490 °C, respectively, while aluminum did not melted until the temperature reached 660 °C, thus aluminum and char can be obtained by carbonization of Tetra Pak waste at 550 °C. Pyrolytic char was processed into porous carbons by different methods. Specific surface area of the porous carbon prepared by carbonization of acid‐washed char at 850 °C achieved 741 m 2 g −1 , and the specific surface area of the porous carbon prepared from char by successively carbonization at 850 °C and acid‐washing was 732 m 2 g −1 . The developed porous structure was formed due to the polymerization of char above 650 °C, while the etching of char by CO 2 generated via decomposition of inherent calcite led to a lower microporosity. Methylene blue adsorption capacity of the optimized sample reached 140 mg g −1 , and the equilibrium data followed Langmuir model.
- 3 January 2021
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 23 (2) , 604-613
Spent coffee ground-based interfacial solar steam generation
- 3 January 2021
- Published by Springer Nature in Journal of Material Cycles and Waste Management
- Vol. 23 (2) , 604-613
Spent coffee ground-based interfacial solar steam generation
- 15 August 2020
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 27 (36) , 45775-45786
Preparation of mechanically robust Fe3O4/porous carbon/diatomite composite monolith for solar steam generation
Mechanically robust Fe3O4/porous carbon/diatomite composite monolith was prepared from waste corrugated cardboard box and diatomite via slurrying in FeCl3 solution, dewatering, molding, and carbonization at 600 °C. The products were characterized by X-ray diffraction (XRD), field emission scanning electron microscope (SEM), N2-adsorption/desorption, Raman spectroscopy, and ultraviolet-visible-near-infrared (UV-Vis-NIR) spectroscopy. The water wettability, photothermal conversion property, and solar steam generation performance of the products were also evaluated. Results showed that the presence of FeCl3 led to the formation of more pores and magnetic Fe3O4 crystallites, while diatomite provided good hydrophilicity for the composite. The product exhibited light absorption above 65% within the wavelength ranging from 200 to1974 nm, and its surface temperature eventually increased by 30 °C under 0.25 sun irradiation due to photothermal effect. Moreover, solar steam yield under 0.25 sun irradiation for 3600 s was improved by 67% with the presence of the monolithic composite because of the occurrence of interfacial solar steam generation and heat transfer from the composite acted as a heat island.
- 15 August 2020
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 27 (36) , 45775-45786
Preparation of mechanically robust Fe3O4/porous carbon/diatomite composite monolith for solar steam generation
Mechanically robust Fe3O4/porous carbon/diatomite composite monolith was prepared from waste corrugated cardboard box and diatomite via slurrying in FeCl3 solution, dewatering, molding, and carbonization at 600 °C. The products were characterized by X-ray diffraction (XRD), field emission scanning electron microscope (SEM), N2-adsorption/desorption, Raman spectroscopy, and ultraviolet-visible-near-infrared (UV-Vis-NIR) spectroscopy. The water wettability, photothermal conversion property, and solar steam generation performance of the products were also evaluated. Results showed that the presence of FeCl3 led to the formation of more pores and magnetic Fe3O4 crystallites, while diatomite provided good hydrophilicity for the composite. The product exhibited light absorption above 65% within the wavelength ranging from 200 to1974 nm, and its surface temperature eventually increased by 30 °C under 0.25 sun irradiation due to photothermal effect. Moreover, solar steam yield under 0.25 sun irradiation for 3600 s was improved by 67% with the presence of the monolithic composite because of the occurrence of interfacial solar steam generation and heat transfer from the composite acted as a heat island.