Siarhei Dzianisau
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Siarhei Dzianisau has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Deokjung Lee
Department of Nuclear Engineering, Ulsan National Institute of Science and Technology (UNIST), Ulsan, Republic of Korea
5 shared publications Alexey Cherezov
2 shared publicationsDeokjung Lee
2 shared publications- Bamidele Ebiwonjumi
Massachusetts Institute of Technology
1 shared publication Fathurrahman Setiawan
1 shared publicationHyun Chul Lee
1 shared publication
Latest Publications
- Open Access
- 10 December 2025
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 58 (4)
Enhancing CMFD acceleration in MOC-based direct transport code
- 10 December 2025
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 58 (4)
Open AccessEnhancing CMFD acceleration in MOC-based direct transport code
- 25 May 2024
- Published by Elsevier in Progress in Nuclear Energy
- Vol. 173
Application of artificial neural network for assembly homogenized equivalence parameter generation
- 25 May 2024
- Published by Elsevier in Progress in Nuclear Energy
- Vol. 173
Application of artificial neural network for assembly homogenized equivalence parameter generation
- 3 March 2023
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 186
Development of an artificial neural network model for generating macroscopic cross-sections for RAST-AI
- 3 March 2023
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 186
Development of an artificial neural network model for generating macroscopic cross-sections for RAST-AI
- Open Access
- 13 April 2022
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 54 (9) , 3494-3515
Development of nodal diffusion code RAST-V for Vodo–Vodyanoi Energetichesky reactor analysis
- 13 April 2022
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 54 (9) , 3494-3515
Open AccessDevelopment of nodal diffusion code RAST-V for Vodo–Vodyanoi Energetichesky reactor analysis
- Open Access
- 1 November 2021
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 53 (11) , 3563-3579
Machine learning of LWR spent nuclear fuel assembly decay heat measurements
- 1 November 2021
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 53 (11) , 3563-3579
Open AccessMachine learning of LWR spent nuclear fuel assembly decay heat measurements
- Open Access
- 22 February 2021
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 247, 07009
DEVELOPMENT OF DECAY HEAT MODEL FOR RAST-K
Decay heat (DH) is the heat produced through a radioactive decay of fission products during or after a reactor operation. It is known as the second largest source of power in the core after fission. Being such a strong contributor to reactor power, it should be accurately determined at any time of reactor operation. Currently, there are two main approaches for DH estimation used in reactor simulation codes. One approach is based on careful inventorying of all produced target nuclides and their individual contributions to total power. Alternatively, the other popular approach is based on collapsing all target fission products into a small number of groups similar to delayed neutron estimation techniques. However, the last (multigroup) method currently has limitations when used in some transient scenarios such as transients occurred in fresh fuel.In this study, the multigroup method was further developed for reducing limitations while retaining the advantage in computation speed. Then, it was implemented into Reactor Analysis code for Steady state and Transient (RAST-K) and tested against other codes. As a result, the improved method was found capable of determining DH power at all tested stages of reactor operation under any tested operation scenario. In particular, the test simulations using the improved method showed better results in those scenarios that were under accuracy limitations of the original multigroup method. Overall, the quality of transient calculations in RAST-K was improved when using the newly implemented DH module.
- 22 February 2021
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 247, 07009
Open AccessDEVELOPMENT OF DECAY HEAT MODEL FOR RAST-K
Decay heat (DH) is the heat produced through a radioactive decay of fission products during or after a reactor operation. It is known as the second largest source of power in the core after fission. Being such a strong contributor to reactor power, it should be accurately determined at any time of reactor operation. Currently, there are two main approaches for DH estimation used in reactor simulation codes. One approach is based on careful inventorying of all produced target nuclides and their individual contributions to total power. Alternatively, the other popular approach is based on collapsing all target fission products into a small number of groups similar to delayed neutron estimation techniques. However, the last (multigroup) method currently has limitations when used in some transient scenarios such as transients occurred in fresh fuel.In this study, the multigroup method was further developed for reducing limitations while retaining the advantage in computation speed. Then, it was implemented into Reactor Analysis code for Steady state and Transient (RAST-K) and tested against other codes. As a result, the improved method was found capable of determining DH power at all tested stages of reactor operation under any tested operation scenario. In particular, the test simulations using the improved method showed better results in those scenarios that were under accuracy limitations of the original multigroup method. Overall, the quality of transient calculations in RAST-K was improved when using the newly implemented DH module.