Mengting Yan
Mengting Yan has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Marvin Onabajo
Northeastern University
8 shared publications - Cristian Cassella
Northeastern University
3 shared publications - Thomas Gourousis
Northeastern University
3 shared publications - Aatmesh Shrivastava
Department of Electrical and Computer Engineering, Northeastern University, Boston, MA, USA
2 shared publications - Francesco Restuccia
Northeastern University
2 shared publications - Miriam Leeser
Electrical and Computer Engineering, Northeastern University, Boston, MA, USA
2 shared publications
Latest Publications
- Open Access
- 9 October 2025
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 125 (2) , 1-10
A design and simulation methodology for radio frequency receiver front-ends with frequency selective limiting devices
It has recently been shown that emerging frequency selective limiter (FSL) devices allow to suppress interference with high power levels in the same frequency band as desired signals. This paper introduces an FSL model for circuit simulations that was validated with measurement results of a prototype FSL device. An RF front-end was constructed with this FSL model and a transistor-level CMOS low-noise amplifier (LNA) design. A co-simulation methodology has been developed under large-signal interference considerations using the Bluetooth Low-Energy (BLE) standard as a representative example. Results from simulations with a two-tone signal confirm that the modeled FSL can provide a 9.4 dB reduction of the third-order intermodulation distortion (IMD3) components, which benefits resilience to interference.
- 9 October 2025
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 125 (2) , 1-10
Open AccessA design and simulation methodology for radio frequency receiver front-ends with frequency selective limiting devices
It has recently been shown that emerging frequency selective limiter (FSL) devices allow to suppress interference with high power levels in the same frequency band as desired signals. This paper introduces an FSL model for circuit simulations that was validated with measurement results of a prototype FSL device. An RF front-end was constructed with this FSL model and a transistor-level CMOS low-noise amplifier (LNA) design. A co-simulation methodology has been developed under large-signal interference considerations using the Bluetooth Low-Energy (BLE) standard as a representative example. Results from simulations with a two-tone signal confirm that the modeled FSL can provide a 9.4 dB reduction of the third-order intermodulation distortion (IMD3) components, which benefits resilience to interference.
- Open Access
- 11 June 2025
- Published by MDPI AG in Electronics
- Vol. 14 (12) , 2381
A Low-Power Differential Temperature Sensor with Chopped Cascode Transistors and Switched-Capacitor Integration
Embedded differential temperature sensors can be utilized to monitor the power consumption of circuits, taking advantage of the inherent on-chip electrothermal coupling. Potential applications range from hardware security to linearity, gain/bandwidth calibration, defect-oriented testing, and compensation for circuit aging effects. This paper introduces the use of on-chip differential temperature sensors as part of a wireless Internet of Things system. A new low-power differential temperature sensor circuit with chopped cascode transistors and switched-capacitor integration is described. This design approach leverages chopper stabilization in combination with a switched-capacitor integrator that acts as a low-pass filter such that the circuit provides offset and low-frequency noise mitigation. Simulation results of the proposed differential temperature sensor in a 65 nm complementary metal-oxide-semiconductor (CMOS) process show a sensitivity of within a linear range of and an integrated output noise of (from 1 to 441.7 Hz) with an overall power consumption of . Considering a figure of merit that involves sensitivity, linear range, noise, and power, the new temperature sensor topology demonstrates a significant improvement compared to state-of-the-art differential temperature sensors for on-chip monitoring of power dissipation.- 11 June 2025
- Published by MDPI AG in Electronics
- Vol. 14 (12) , 2381
Open AccessA Low-Power Differential Temperature Sensor with Chopped Cascode Transistors and Switched-Capacitor Integration
Embedded differential temperature sensors can be utilized to monitor the power consumption of circuits, taking advantage of the inherent on-chip electrothermal coupling. Potential applications range from hardware security to linearity, gain/bandwidth calibration, defect-oriented testing, and compensation for circuit aging effects. This paper introduces the use of on-chip differential temperature sensors as part of a wireless Internet of Things system. A new low-power differential temperature sensor circuit with chopped cascode transistors and switched-capacitor integration is described. This design approach leverages chopper stabilization in combination with a switched-capacitor integrator that acts as a low-pass filter such that the circuit provides offset and low-frequency noise mitigation. Simulation results of the proposed differential temperature sensor in a 65 nm complementary metal-oxide-semiconductor (CMOS) process show a sensitivity of within a linear range of and an integrated output noise of (from 1 to 441.7 Hz) with an overall power consumption of . Considering a figure of merit that involves sensitivity, linear range, noise, and power, the new temperature sensor topology demonstrates a significant improvement compared to state-of-the-art differential temperature sensors for on-chip monitoring of power dissipation. - Open Access
- 2 July 2024
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 120 (1) , 83-91
An offset calibration scheme for on-chip thermal profiling with differential temperature sensors
This paper introduces an on-chip analog calibration method tailored for differential temperature sensors in thermal monitoring applications. A three-step calibration process is proposed within a two-stage high-gain instrumentation amplifier to compensate for the output voltage offset due to device mismatches and on-chip temperature gradients. The calibration circuits were designed in a standard 65 nm CMOS process for simulation. Results indicate that an input-referred offset with a mean of 0.2 μV can be achieved after calibration, through which the standard deviation is greatly reduced fromσ = 880.3 toσ = 5086 μV. Furthermore, the proposed analog offset calibration scheme has negligible impact on the sensitivity of the complete temperature sensor circuit, as shown by Monte Carlo and process-temperature corner simulation results.
- 2 July 2024
- Published by Springer Nature in Analog Integrated Circuits and Signal Processing
- Vol. 120 (1) , 83-91
Open AccessAn offset calibration scheme for on-chip thermal profiling with differential temperature sensors
This paper introduces an on-chip analog calibration method tailored for differential temperature sensors in thermal monitoring applications. A three-step calibration process is proposed within a two-stage high-gain instrumentation amplifier to compensate for the output voltage offset due to device mismatches and on-chip temperature gradients. The calibration circuits were designed in a standard 65 nm CMOS process for simulation. Results indicate that an input-referred offset with a mean of 0.2 μV can be achieved after calibration, through which the standard deviation is greatly reduced fromσ = 880.3 toσ = 5086 μV. Furthermore, the proposed analog offset calibration scheme has negligible impact on the sensitivity of the complete temperature sensor circuit, as shown by Monte Carlo and process-temperature corner simulation results.
- 27 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-4
On-Chip Power Monitoring: Leveraging High-Sensitivity Differential Temperature Sensors With Chopper Stabilization and Offset Calibration
This paper introduces a differential temperature sensor that is tailored for on-chip thermal profiling to monitor the power dissipation of circuits. Chopper stabilization and analog offset calibration are integrated within the sensor circuit design to suppress low-frequency flicker noise and DC offsets, respectively. A prototype chip of the proposed temperature sensor with on-chip test heat sources was fabricated in a standard 65-nm CMOS process. A measured sensitivity of 21.1 mV/μW is achieved over a dynamic range of 34 μW, which is the highest sensitivity reported for an on-chip differential temperature sensor. To the best of the authors’ knowledge, the described work is the first differential temperature sensor circuit with integrated chopping and automatic analog offset calibration, which allows to obtain high sensitivity within the dynamic range of interest. These results lay the foundation for on-chip thermal monitoring in future analog, digital, and RF systems-on-a-chips (SoCs).
- 27 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-4
On-Chip Power Monitoring: Leveraging High-Sensitivity Differential Temperature Sensors With Chopper Stabilization and Offset Calibration
This paper introduces a differential temperature sensor that is tailored for on-chip thermal profiling to monitor the power dissipation of circuits. Chopper stabilization and analog offset calibration are integrated within the sensor circuit design to suppress low-frequency flicker noise and DC offsets, respectively. A prototype chip of the proposed temperature sensor with on-chip test heat sources was fabricated in a standard 65-nm CMOS process. A measured sensitivity of 21.1 mV/μW is achieved over a dynamic range of 34 μW, which is the highest sensitivity reported for an on-chip differential temperature sensor. To the best of the authors’ knowledge, the described work is the first differential temperature sensor circuit with integrated chopping and automatic analog offset calibration, which allows to obtain high sensitivity within the dynamic range of interest. These results lay the foundation for on-chip thermal monitoring in future analog, digital, and RF systems-on-a-chips (SoCs).
- 7 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 70 (5) , 1893-1906
Design and Analysis of an On-Chip Current-Driven CMOS Parametric Frequency Divider
This paper introduces an on-chip current-driven CMOS parametric frequency divider (PFD) that provides 2:1 frequency division with an output frequency of 2.4 GHz. A custom input driver stage with a buffer enables to generate the input current of the PFD core from a digital clock signal or sinusoidal source, and a band-pass filter (BPF) stage suppresses undesirable harmonics at the output. Analyses and discussions of design considerations provide insights into the PFD’s input driving conditions, filtering characteristics of the output driver, as well as the effects of the limited quality (Q) factor of passive components and layout parasitics. A prototype chip was fabricated in standard 65-nm CMOS technology and tested. The minimum required supply voltage for the PFD driver is 1.4 V with an input frequency of 4.8 GHz, whereas the PFD has an operating frequency range from 4.5 GHz to 5.1 GHz with a supply voltage of 1.5 V. To the best of the authors’ knowledge, the proposed PFD is the first on-chip implementation of a current-driven parametric frequency divider in a standard CMOS process with sub-6 GHz operation, which demonstrates the feasibility of on-chip integration into RF systems.
- 7 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 70 (5) , 1893-1906
Design and Analysis of an On-Chip Current-Driven CMOS Parametric Frequency Divider
This paper introduces an on-chip current-driven CMOS parametric frequency divider (PFD) that provides 2:1 frequency division with an output frequency of 2.4 GHz. A custom input driver stage with a buffer enables to generate the input current of the PFD core from a digital clock signal or sinusoidal source, and a band-pass filter (BPF) stage suppresses undesirable harmonics at the output. Analyses and discussions of design considerations provide insights into the PFD’s input driving conditions, filtering characteristics of the output driver, as well as the effects of the limited quality (Q) factor of passive components and layout parasitics. A prototype chip was fabricated in standard 65-nm CMOS technology and tested. The minimum required supply voltage for the PFD driver is 1.4 V with an input frequency of 4.8 GHz, whereas the PFD has an operating frequency range from 4.5 GHz to 5.1 GHz with a supply voltage of 1.5 V. To the best of the authors’ knowledge, the proposed PFD is the first on-chip implementation of a current-driven parametric frequency divider in a standard CMOS process with sub-6 GHz operation, which demonstrates the feasibility of on-chip integration into RF systems.
- 13 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 29 (3) , 530-543
On-Chip Thermal Profiling to Detect Malicious Activity: System-Level Concepts and Design of Key Building Blocks
This article introduces an on-chip anomaly monitoring system design approach that is based on thermal profiling and side-channel analysis. The strategy aims at the realization of nonintrusive hardware Trojan (HT) detection over the lifetime of the circuit under test (CUT). To evaluate the capability of the proposed HT detection system, the on-chip electrothermal coupling is modeled as part of the simulation technique, which associates local thermal activities with circuit-level power consumption using a standard electrical simulator. To monitor the thermal profiles on chips with high sensitivity to local temperature changes and the resilience to flicker noise, the sensor architecture described in this article is the first differential temperature sensor equipped with a chopping mechanism. A methodology is described to utilize principal component analysis (PCA) to extract critical information from the quantized output of the system for effective HT detection in the presence of noise. The complete sensor signal path of the system was designed and simulated with foundry-supplied device models (130-nm CMOS technology), and the impact due to process variations have been considered via Monte Carlo simulations. The results indicate that small Trojans with approximately 2 μW of power can be detected within the thermal profile of a CUT consuming more than 500 μW. As the first step to prove the feasibility of on-chip quantization in the HT detection system, a prototype 8-bit successive approximation register (SAR) analog-to-digital converter (ADC) was fabricated with 130-nm CMOS technology.
- 13 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 29 (3) , 530-543
On-Chip Thermal Profiling to Detect Malicious Activity: System-Level Concepts and Design of Key Building Blocks
This article introduces an on-chip anomaly monitoring system design approach that is based on thermal profiling and side-channel analysis. The strategy aims at the realization of nonintrusive hardware Trojan (HT) detection over the lifetime of the circuit under test (CUT). To evaluate the capability of the proposed HT detection system, the on-chip electrothermal coupling is modeled as part of the simulation technique, which associates local thermal activities with circuit-level power consumption using a standard electrical simulator. To monitor the thermal profiles on chips with high sensitivity to local temperature changes and the resilience to flicker noise, the sensor architecture described in this article is the first differential temperature sensor equipped with a chopping mechanism. A methodology is described to utilize principal component analysis (PCA) to extract critical information from the quantized output of the system for effective HT detection in the presence of noise. The complete sensor signal path of the system was designed and simulated with foundry-supplied device models (130-nm CMOS technology), and the impact due to process variations have been considered via Monte Carlo simulations. The results indicate that small Trojans with approximately 2 μW of power can be detected within the thermal profile of a CUT consuming more than 500 μW. As the first step to prove the feasibility of on-chip quantization in the HT detection system, a prototype 8-bit successive approximation register (SAR) analog-to-digital converter (ADC) was fabricated with 130-nm CMOS technology.