Alp T. Findikoglu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Alp T. Findikoglu has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Quanxi X. Jia
Department of Materials Design and Innovation, University at Buffalo, 136 Bell Hall, Buffalo, NY 14260, USA
3 shared publications - Rajendra Prasath Palanisamy
Materials Physics and Applications (MPA), Los Alamos National Laboratory, Los Alamos, NM 87545, USA
2 shared publications - Taeho Ju
Materials Physics and Applications (MPA), Los Alamos National Laboratory, Los Alamos, NM 87545, USA
2 shared publications V. Matias
Los Alamos National Laboratory, Los Alamos Materials Science and Technology Division New Mexico 87545
2 shared publicationsW. Choi
Los Alamos National Laboratory, Los Alamos Materials Science and Technology Division New Mexico 87545
2 shared publicationsA.R. Bishop
Los Alamos National Laboratory, Los Alamos, NM 87545
1 shared publication
Latest Publications
- Open Access
Accurate Ultrasonic Thickness Measurement for Arbitrary Time-Variant Thermal Profile
Ultrasonic thickness measurement of mechanical structures is one of the most popular and commonly used nondestructive methods for various kinds of process control and corrosion monitoring. With ultrasonic propagation speed being temperature-dependent, the thickness measurement can be performed reliably only when the thermal profile is completely known. Most conventional techniques assume the temperature of the test structure is uniform and at room temperature across its thickness. Such assumptions may lead to large errors in the thickness measurement, especially when there are significant temperature variations across the thickness. State-of-the-art techniques use external temperature measurements or implement iterative methods to compensate for the unknown thermal profiles. However, such techniques produce unsatisfactory results when the heat distribution is complex or varies rapidly with time. In this work, we propose a two-sensors technique, using both compressive and shear excitations, with a non-iterative rapid data processing method for accurate thickness measurement under arbitrary time-variant thermal profile. The independent behavior of shear and compressive waves is used to formulate a real-time thickness estimation technique. The developed technique is experimentally validated on a steel plate with fixed acoustic sensors. Test results show that the error in thickness estimation can be reduced by up to 98% compared to conventional thickness gauging methods.
Open AccessAccurate Ultrasonic Thickness Measurement for Arbitrary Time-Variant Thermal Profile
Ultrasonic thickness measurement of mechanical structures is one of the most popular and commonly used nondestructive methods for various kinds of process control and corrosion monitoring. With ultrasonic propagation speed being temperature-dependent, the thickness measurement can be performed reliably only when the thermal profile is completely known. Most conventional techniques assume the temperature of the test structure is uniform and at room temperature across its thickness. Such assumptions may lead to large errors in the thickness measurement, especially when there are significant temperature variations across the thickness. State-of-the-art techniques use external temperature measurements or implement iterative methods to compensate for the unknown thermal profiles. However, such techniques produce unsatisfactory results when the heat distribution is complex or varies rapidly with time. In this work, we propose a two-sensors technique, using both compressive and shear excitations, with a non-iterative rapid data processing method for accurate thickness measurement under arbitrary time-variant thermal profile. The independent behavior of shear and compressive waves is used to formulate a real-time thickness estimation technique. The developed technique is experimentally validated on a steel plate with fixed acoustic sensors. Test results show that the error in thickness estimation can be reduced by up to 98% compared to conventional thickness gauging methods.
- Open Access
Void-Engineered Metamaterial Delay Line with Built-In Impedance Matching for Ultrasonic Applications
Metamaterials exhibit unique ultrasonic properties that are not always achievable with traditional materials. However, the structures and geometries needed to achieve such properties are often complex and difficult to obtain using common fabrication techniques. In the present research work, we report a novel metamaterial acoustic delay line with built-in impedance matching that is fabricated using a common 3D printer. Delay lines are commonly used in ultrasonic inspection when signals need to be separated in time for improved sensitivity. However, if the impedance of the delay line is not perfectly matched with those of both the sensor and the target medium, a strong standing wave develops in the delay line, leading to a lower energy transmission. The presented metamaterial delay line was designed to match the acoustic impedance at both the sensor and target medium interfaces. This was achieved by introducing graded engineered voids with different densities at both ends of the delay line. The measured impedances of the designed metamaterial samples show a good match with the theoretical predictions. The experimental test results with concrete samples show that the acoustic energy transmission is increased by 120% and the standing wave in the delay line is reduced by over a factor of 2 compared to a commercial delay line.
Open AccessVoid-Engineered Metamaterial Delay Line with Built-In Impedance Matching for Ultrasonic Applications
Metamaterials exhibit unique ultrasonic properties that are not always achievable with traditional materials. However, the structures and geometries needed to achieve such properties are often complex and difficult to obtain using common fabrication techniques. In the present research work, we report a novel metamaterial acoustic delay line with built-in impedance matching that is fabricated using a common 3D printer. Delay lines are commonly used in ultrasonic inspection when signals need to be separated in time for improved sensitivity. However, if the impedance of the delay line is not perfectly matched with those of both the sensor and the target medium, a strong standing wave develops in the delay line, leading to a lower energy transmission. The presented metamaterial delay line was designed to match the acoustic impedance at both the sensor and target medium interfaces. This was achieved by introducing graded engineered voids with different densities at both ends of the delay line. The measured impedances of the designed metamaterial samples show a good match with the theoretical predictions. The experimental test results with concrete samples show that the acoustic energy transmission is increased by 120% and the standing wave in the delay line is reduced by over a factor of 2 compared to a commercial delay line.
- Open Access
Ultrasonic Testing of Mechanical Changes in a Water-Filled Pipe with Multi-Mode and Broadband Signals and Two-Level Compensation
Ultrasonic testing (UT) has been widely used for the Nondestructive Evaluation (NDE) of pipes due to its many favorable characteristics. However, one of the main challenges in the general use of UT for real-world pipelines is the sensitivity of this method to environmental and operational condition changes. This paper proposes a new UT method with enhanced compensation for environmental effects and operational condition changes. In particular, the effectiveness of the new method is tested in the presence of temperature variations, and changes in water flow rate inside a stainless-steel pipe. The proposed UT method uses multi-mode and broadband guided ultrasonic waves in the pipe walls, excited and received by single-element ultrasonic sensors that are spatially separated, forming a measurement zone between any pair of such transmit and receive sensors. Amplitude changes, time shifts, and frequency content variations in the ultrasonic signal due to temperature changes and water flow are evaluated and compensated for reliable UT of mechanical changes in the pipe. It is observed that spurious effects of water flow on ultrasonic response, if not properly compensated, can dominate over effects due to actual mechanical changes, but such liquid-boundary effects can be compensated effectively by the proposed time- and frequency-filtering method.
Open AccessUltrasonic Testing of Mechanical Changes in a Water-Filled Pipe with Multi-Mode and Broadband Signals and Two-Level Compensation
Ultrasonic testing (UT) has been widely used for the Nondestructive Evaluation (NDE) of pipes due to its many favorable characteristics. However, one of the main challenges in the general use of UT for real-world pipelines is the sensitivity of this method to environmental and operational condition changes. This paper proposes a new UT method with enhanced compensation for environmental effects and operational condition changes. In particular, the effectiveness of the new method is tested in the presence of temperature variations, and changes in water flow rate inside a stainless-steel pipe. The proposed UT method uses multi-mode and broadband guided ultrasonic waves in the pipe walls, excited and received by single-element ultrasonic sensors that are spatially separated, forming a measurement zone between any pair of such transmit and receive sensors. Amplitude changes, time shifts, and frequency content variations in the ultrasonic signal due to temperature changes and water flow are evaluated and compensated for reliable UT of mechanical changes in the pipe. It is observed that spurious effects of water flow on ultrasonic response, if not properly compensated, can dominate over effects due to actual mechanical changes, but such liquid-boundary effects can be compensated effectively by the proposed time- and frequency-filtering method.
- Open Access
- 17 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (4) , 2082
Large Area Detection of Microstructural Defects with Multi-Mode Ultrasonic Signals
Cyclic loading or other stresses can lead to development of cracks and crack growth in mechanical structures, leading to eventual failure. While ultrasound imaging can be used for non-destructive testing of such structures, conventional ultrasound techniques are often limited by crack size, density, and areal coverage. An effective characterization of real-world, large-area structures is required at an early damage stage to prevent catastrophic failure and predict remaining life. In this study, a new nonlinear ultrasonic testing (NUT) method is proposed for large-area monitoring of practical structures with arbitrary complexity by using multiple-mode guided-wave ultrasonic signals. The proposed guided-wave NUT technique requires single-element transducers, simple electronics, and a mixed time-frequency domain signal processing. As a proof-of-concept demonstration, numerical simulations and experiments are performed on an A36 carbon steel beam assembly with previously formed microstructural defects that cause nonlinearities in ultrasonic response. The quadratic dependence of the nonlinear wave excitation on the input ultrasonic signal amplitude is shown by numerical simulations, and such a nonlinear ultrasonic response is experimentally observed in the zone with a high density of microstructural defects.
- 17 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (4) , 2082
Open AccessLarge Area Detection of Microstructural Defects with Multi-Mode Ultrasonic Signals
Cyclic loading or other stresses can lead to development of cracks and crack growth in mechanical structures, leading to eventual failure. While ultrasound imaging can be used for non-destructive testing of such structures, conventional ultrasound techniques are often limited by crack size, density, and areal coverage. An effective characterization of real-world, large-area structures is required at an early damage stage to prevent catastrophic failure and predict remaining life. In this study, a new nonlinear ultrasonic testing (NUT) method is proposed for large-area monitoring of practical structures with arbitrary complexity by using multiple-mode guided-wave ultrasonic signals. The proposed guided-wave NUT technique requires single-element transducers, simple electronics, and a mixed time-frequency domain signal processing. As a proof-of-concept demonstration, numerical simulations and experiments are performed on an A36 carbon steel beam assembly with previously formed microstructural defects that cause nonlinearities in ultrasonic response. The quadratic dependence of the nonlinear wave excitation on the input ultrasonic signal amplitude is shown by numerical simulations, and such a nonlinear ultrasonic response is experimentally observed in the zone with a high density of microstructural defects.
- 1 January 2008
- Published by Springer Nature in MRS Proceedings
- Vol. 1066
Aligned-Crystalline Si Films on Glass
We report structural and electronic properties of Aligned-Crystalline Si (ACSi) films on glass substrates. These films show enhanced majority carrier mobilities and minority carrier lifetimes with increasing crystallinity, i.e., with improving alignment and connectivity of the grains. A 0.4-μm-thick ACSi film with a total grain mosaic spread of 4.2° showed Hall mobility of 47 cm2/V.s for a p-type doping concentration of 1.9×1018 cm−3. A prototype n+/p/p+–type diode fabricated using a 4.2-μm-thick ACSi film showed minority carrier lifetime of ∼3.5 μs and estimated diffusion length of ∼30 μm in the p layer with a doping concentration of 5×1016 cm−3.
- 1 January 2008
- Published by Springer Nature in MRS Proceedings
- Vol. 1066
Aligned-Crystalline Si Films on Glass
We report structural and electronic properties of Aligned-Crystalline Si (ACSi) films on glass substrates. These films show enhanced majority carrier mobilities and minority carrier lifetimes with increasing crystallinity, i.e., with improving alignment and connectivity of the grains. A 0.4-μm-thick ACSi film with a total grain mosaic spread of 4.2° showed Hall mobility of 47 cm2/V.s for a p-type doping concentration of 1.9×1018 cm−3. A prototype n+/p/p+–type diode fabricated using a 4.2-μm-thick ACSi film showed minority carrier lifetime of ∼3.5 μs and estimated diffusion length of ∼30 μm in the p layer with a doping concentration of 5×1016 cm−3.
- 6 February 2006
- Published by AIP Publishing in Applied Physics Letters
- Vol. 88 (6) , 062907
Dielectric properties of ⟨001⟩-oriented Ba0.6Sr0.4TiO3 thin films on polycrystalline metal tapes using biaxially oriented MgO∕γ-Al2O3 buffer layers
We report the growth of -oriented (BST) thin films on polycrystalline Ni-alloy tapes by pulsed laser deposition using biaxially oriented, ion-beam-assisted deposited (IBAD) and buffer layers. Dielectric constant values of our BST films were up to of those in the epitaxial films prepared under similar conditions on single-crystal substrates. No significant dispersion of the dielectric constant was observed for frequencies from to . These results demonstrate the versatility of using IBAD-textured and buffer layers to integrate highly oriented good-quality BST films with nonsingle-crystalline substrates.- 6 February 2006
- Published by AIP Publishing in Applied Physics Letters
- Vol. 88 (6) , 062907
Dielectric properties of ⟨001⟩-oriented Ba0.6Sr0.4TiO3 thin films on polycrystalline metal tapes using biaxially oriented MgO∕γ-Al2O3 buffer layers
We report the growth of -oriented (BST) thin films on polycrystalline Ni-alloy tapes by pulsed laser deposition using biaxially oriented, ion-beam-assisted deposited (IBAD) and buffer layers. Dielectric constant values of our BST films were up to of those in the epitaxial films prepared under similar conditions on single-crystal substrates. No significant dispersion of the dielectric constant was observed for frequencies from to . These results demonstrate the versatility of using IBAD-textured and buffer layers to integrate highly oriented good-quality BST films with nonsingle-crystalline substrates.- 7 June 2005
- Published by Wiley in Advanced Materials
- Vol. 17 (12) , 1527-1531
Well‐Oriented Silicon Thin Films with High Carrier Mobility on Polycrystalline Substrates
- 7 June 2005
- Published by Wiley in Advanced Materials
- Vol. 17 (12) , 1527-1531
Well‐Oriented Silicon Thin Films with High Carrier Mobility on Polycrystalline Substrates
- 1 February 2004
- Published by Springer Nature in Journal of Materials Research
- Vol. 19 (02) , 501-504
Role of beam divergence and ion-to-molecule flux ratio in ion-beam-assisted deposition texturing of MgO
- 1 February 2004
- Published by Springer Nature in Journal of Materials Research
- Vol. 19 (02) , 501-504
Role of beam divergence and ion-to-molecule flux ratio in ion-beam-assisted deposition texturing of MgO
- 1 January 1999
- Published by Springer Nature in MRS Proceedings
- Vol. 603
Electrodynamic Properties of Single-Crystal and Thin-Film Strontium Titanate, and Thin-Film Barium Strontium Titanate
We have used a coplanar waveguide structure to study broadband electrodynamic properties of single-crystal and thin-film strontium titanate (STO), and thin-film barium strontium titanate (BSTO). We have implemented low-frequency capacitance (100 Hz - 1 MHz), swept-frequency transmittance (45 MHz - 4 GHz), and time-domain transmittance (dc - several GHz) measurements to determine effective refractive index (or, dielectric constant), and dissipation factor (or, loss tangent) as a function of dc bias (up to 4×106 V/m) and temperature (20 - 300 K). The STO samples used superconducting electrodes and were designed to operate at cryogenic temperatures, whereas BSTO samples used normal conducting electrodes and exhibited optimal performance around room temperature. By using nearly identical electrode geometries for all devices, we were able to conduct a direct comparative study among them, and investigate not only single-crystal vs thin-film, but also cryogenic vs room-temperature applications.
- 1 January 1999
- Published by Springer Nature in MRS Proceedings
- Vol. 603
Electrodynamic Properties of Single-Crystal and Thin-Film Strontium Titanate, and Thin-Film Barium Strontium Titanate
We have used a coplanar waveguide structure to study broadband electrodynamic properties of single-crystal and thin-film strontium titanate (STO), and thin-film barium strontium titanate (BSTO). We have implemented low-frequency capacitance (100 Hz - 1 MHz), swept-frequency transmittance (45 MHz - 4 GHz), and time-domain transmittance (dc - several GHz) measurements to determine effective refractive index (or, dielectric constant), and dissipation factor (or, loss tangent) as a function of dc bias (up to 4×106 V/m) and temperature (20 - 300 K). The STO samples used superconducting electrodes and were designed to operate at cryogenic temperatures, whereas BSTO samples used normal conducting electrodes and exhibited optimal performance around room temperature. By using nearly identical electrode geometries for all devices, we were able to conduct a direct comparative study among them, and investigate not only single-crystal vs thin-film, but also cryogenic vs room-temperature applications.