Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ju-Hun Ahn has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Temperature Calibration Using Machine Learning Algorithms for Flexible Temperature Sensors

    by Ui-Jin Kim, Ju-Hun Ahn, Ji-Han Lee, Chang-Yull Lee

    Thermal imbalance can cause significant stress in large-scale structures such as bridges and buildings, negatively impacting their structural health. To assist in the structural health monitoring systems that analyze these thermal effects, a flexible temperature sensor was fabricated using EHD inkjet printing. However, the reliability of such printed sensors is challenged by complex dynamic hysteresis under rapid thermal changes. To address this, an LSTM calibration model was developed and trained exclusively on quasi-static data across the 20–70 °C temperature range, where it achieved a low prediction error, a 33.563% improvement over a conventional polynomial regression. More importantly, when tested on unseen dynamic data, this statically trained model demonstrated superior generalization, reducing the RMSE from 12.451 °C for the polynomial model to 4.899 °C. These results suggest that data-driven approaches like LSTM can be a highly effective solution for ensuring the reliability of flexible sensors in real-world SHM applications.


  • Open Access

    Crack Detecting Method Based on Grid-Type Sensing Networks Using Electrical Signals

    by Ju-Hun Ahn, Yong-Chan Lee, Se-Min Jeong, Han-Na Kim, Chang-Yull Lee

    Cracks have a primary effect on the failure of a structure. Therefore, the development of crack sensors with high accuracy and resolution and cracks detection method are important. In this study, the crack sensors were fabricated, and the crack locations were detected with the electrical signal of the crack sensor. First, a metal grid-type micro-crack sensor based on silver was fabricated. The sensor is made with electrohydrodynamics (EHD) inkjet printing technology, which is well known as the next generation of printed electronics technology. Optimal printing conditions were established through experiments, and a grid sensor was obtained. After that, single cracks and multiple cracks were simulated on the sensor, and electrical signals generated from the sensor were measured. The measured electrical signal tracked the location of the cracks in three steps: simple cross-calculation, interpolation, and modified P-SPICE. It was confirmed that cracks could be effectively found and displayed using the method presented in this paper.


  • Open Access

    Evaluation of Temperature Sensors for Detection of Heat Sources Using Additive Printing Method

    by Ju-Hun Ahn, Han-Na Kim, Jin Yeon Cho, Jeong Ho Kim, Chang-Yull Lee

    Electrohydrodynamic (EHD) inkjet printing is an efficient technique for printing multiple sensors in a multifaceted area. It can be applied to various fields according to the shape of the printing result and the algorithm employed. In this study, temperature sensors capable of detecting heat sources were fabricated. Inks suitable for EHD inkjet printing were produced, and optimal parameters for printing were determined. Printing was performed using the corresponding parameters, and various printing results were obtained. Furthermore, an experiment was conducted to confirm the temperature measurement characteristics of the results and the tolerance of the sensor. Grid-type sensors were fabricated based on the results, and the sensor characteristics were confirmed in an orthogonal form. Heat was applied to arbitrary positions. Resistance to changes due to heat was measured, and the location at which the heat was generated was detected by varying the change in resistance. Through this study, efficient heat control can be achieved, as the location of the heat source can be identified quickly.


  • Open Access

    Temperature-Sensing Inks Using Electrohydrodynamic Inkjet Printing Technology

    by Ju-Hun Ahn, Hee-Ju Hong, Chang-Yull Lee

    Temperature measurement is very important for thermal control, which is required for the advancement of mechanical and electronic devices. However, current temperature sensors are limited by their inability to measure curved surfaces. To overcome this problem, several methods for printing flexible substrates were proposed. Among them, electrohydrodynamic (EHD) inkjet printing technology was adopted because it has the highest resolution. Since EHD inkjet printing technology is limited by the type of ink used, an ink with temperature-sensing properties was manufactured for use in this printer. To confirm the applicability of the prepared ink, its resistance characteristics were investigated, and the arrangement and characteristics of the particles were observed. Then, the ink was printed using the EHD inkjet approach. In addition, studies of the meniscus shapes and line widths of the printed results under various conditions confirmed the applicability of the ink to the EHD inkjet printing technology and the change in its resistance with temperature.


  • Open Access

    Flexible Structural Color Films Based on Electro-Hydrodynamic Inkjet Printing

    by Ju-Hwan Choi, Ju-Hun Ahn, Chang-Yull Lee

    Structural coloration based on nanostructures is one of the alternatives that can prevent environmental pollution compared to the use of chemically synthesized materials. This technique has attracted considerable attention for various applications, including displays and sensors. In this study, a photonic crystal structure based on spherical silica was formed to provide structural color using an electro-hydrodynamic (EHD) equipment, a printed electronic system attracting considerable interest. The EHD inkjet printing equipment could print micro- and nanostructures using the voltage applied between the nozzle and substrate. Silica-based ink samples were prepared for use in the EHD equipment. Appropriate printing parameters for the EHD inkjet printing were set using the prepared sample. Spherical silica was printed on a polyimide (PI) film layer. The spherical silica nanoparticles discharged during the EHD inkjet printing were not deformed by the EHD process. A photonic crystal structure was formed on a polydimethylsiloxane (PDMS) layer by EHD printing by covering the PDMS layer on the PI film. The spherical-silica-based photonic crystal structure formed on the PDMS layer with elasticity and flexibility exhibited a color change with bending loads.