Parjaree Thavorniti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Parjaree Thavorniti has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
A. Kongkaew
National Metal and Materials Technology Center , Pathumthani , Thailand
1 shared publicationS. Loykulnant
National Metal and Materials Technology Center , Pathumthani , Thailand
1 shared publicationS. Vichaphund
National Metal and Materials Technology Center, Pathumthani, Thailand
1 shared publicationSasijuta Wattanarach
National Metal and Materials Technology Center, National Science and Technology Development Agency (NSTDA), Pathum Thani, Thailand
1 shared publicationSitthisuntorn Supothina
National Metal and Materials Technology Center, National Science and Technology Development Agency (NSTDA), Pathum Thani, Thailand
1 shared publicationW. Intiya
National Metal and Materials Technology Center , Pathumthani , Thailand
1 shared publication
Latest Publications
- Open Access
- 3 July 2022
- Published by Taylor & Francis in Journal of Asian Ceramic Societies
- Vol. 10 (3) , 567-574
Preparation and properties of metakaolin-based porous geopolymer formed with sodium perborate
This work aimed to study the use of sodium perborate as a foaming agent in the production of porous metakaolin-based geopolymer. The influence of sodium perborate foaming agent on physical properties, mechanical properties, and thermal conductivity was focused. The results revealed that the porosity and pore size increased with an increment of the additions of sodium perborate from 0.5 to 2.0 wt.%. The obtained porous geopolymers showed compressive strength of 5–6 MPa and thermal conductivity in the range of 0.22–0.32 W/mK. The addition of sodium perborate produced porous geopolymer with acceptable compressive strength and thermal conductivity.
- 3 July 2022
- Published by Taylor & Francis in Journal of Asian Ceramic Societies
- Vol. 10 (3) , 567-574
Open AccessPreparation and properties of metakaolin-based porous geopolymer formed with sodium perborate
This work aimed to study the use of sodium perborate as a foaming agent in the production of porous metakaolin-based geopolymer. The influence of sodium perborate foaming agent on physical properties, mechanical properties, and thermal conductivity was focused. The results revealed that the porosity and pore size increased with an increment of the additions of sodium perborate from 0.5 to 2.0 wt.%. The obtained porous geopolymers showed compressive strength of 5–6 MPa and thermal conductivity in the range of 0.22–0.32 W/mK. The addition of sodium perborate produced porous geopolymer with acceptable compressive strength and thermal conductivity.
- 5 April 2012
- Published by Taylor & Francis in Environmental Technology
- Vol. 33 (22) , 2507-2510
Utilization of sludge waste from natural rubber manufacturing process as a raw material for clay-ceramic production
The possibility of utilization of the sludge waste obtained from the natural rubber manufacturing process as a raw material for producing clay ceramics was investigated. To prepared clay-based ceramic, the mixtures of traditional clay and sludge waste (10–30 wt%) were milled, uniaxilly pressed and sintered at a temperature between 1000 and 1200°C. The effect of sludge waste on the properties of clay-based ceramic products was examined. The results showed that the amount of sludge waste addition had an effect on both sinterability and properties of the clay ceramics. Up to 30 wt% of sludge waste can be added into the clay ceramics, and the sintered samples showed good properties.
- 5 April 2012
- Published by Taylor & Francis in Environmental Technology
- Vol. 33 (22) , 2507-2510
Utilization of sludge waste from natural rubber manufacturing process as a raw material for clay-ceramic production
The possibility of utilization of the sludge waste obtained from the natural rubber manufacturing process as a raw material for producing clay ceramics was investigated. To prepared clay-based ceramic, the mixtures of traditional clay and sludge waste (10–30 wt%) were milled, uniaxilly pressed and sintered at a temperature between 1000 and 1200°C. The effect of sludge waste on the properties of clay-based ceramic products was examined. The results showed that the amount of sludge waste addition had an effect on both sinterability and properties of the clay ceramics. Up to 30 wt% of sludge waste can be added into the clay ceramics, and the sintered samples showed good properties.