Iftikhar A. Soomro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Iftikhar A. Soomro has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Ian K. Jennions
IVHM Centre, Cranfield University, UK
2 shared publications - Mohammad Samie
Faculty of Engineering and Applied Sciences, Cranfield University, Cranfield MK43 0AL, UK
2 shared publications Anser Ahmad
1 shared publication- Rana Hammad Raza
National University of Sciences and Technology (NUST)
1 shared publication
Latest Publications
- 1 February 2022
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 177
Printed Circuit Board identification using Deep Convolutional Neural Networks to facilitate recycling
- 1 February 2022
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 177
Printed Circuit Board identification using Deep Convolutional Neural Networks to facilitate recycling
- Open Access
- 17 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 75892-75904
Reduced Pin-Count Test Strategy for 3D Stacked ICs Using Simultaneous Bi-Directional Signaling Based Time Division Multiplexing
3D Stacked Integrated Circuits (SICs) offer a promising way to cope with the technology scaling; however, the test access requirements are highly complicated due to increased transistor density and a limited number of test channels. Moreover, although the vertical interconnects in 3D SIC are capable of high-speed data transfer, the overall test speed is restricted by scan-chains that are not optimized for timing. Reduced Pin-Count Testing (RPCT) has been effectively used under these scenarios. In particular, Time Division Multiplexing (TDM) allows full utilization of interconnect bandwidth while providing low scan frequencies supported by the scan chains. However, these methods rely on Uni-Directional Signaling (UDS), in which a chip terminal (pin or a TSV) can either be used to transmit or receive data at a given time. This requires that at least two chip terminals are available at every die interface (Tester-Die or Die-Die) to form a single test channel. In this paper, we propose Simultaneous Bi-Directional Signaling (SBS), which allows a chip terminal to be used simultaneously to send and receive data, thus forming a test channel using one pin instead of two. We demonstrate how SBS can be used in conjunction with TDM to achieve reduced pin count testing while using only half the number of pins compared to conventional TDM based methods, consuming only 22.6% additional power. Alternatively, the advantage could be manifested as a test time reduction by utilizing all available test channels, allowing more parallelism and test time reduction down to half compared to UDS-based TDM. Experiments using 45nm technology suggest that the proposed method can operate at up to 1.2 GHz test clock for a stack of 3-dies, whereas for higher frequencies, a binary-weighted transmitter is proposed capable of up to 2.46 GHz test clock.
- 17 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 75892-75904
Open AccessReduced Pin-Count Test Strategy for 3D Stacked ICs Using Simultaneous Bi-Directional Signaling Based Time Division Multiplexing
3D Stacked Integrated Circuits (SICs) offer a promising way to cope with the technology scaling; however, the test access requirements are highly complicated due to increased transistor density and a limited number of test channels. Moreover, although the vertical interconnects in 3D SIC are capable of high-speed data transfer, the overall test speed is restricted by scan-chains that are not optimized for timing. Reduced Pin-Count Testing (RPCT) has been effectively used under these scenarios. In particular, Time Division Multiplexing (TDM) allows full utilization of interconnect bandwidth while providing low scan frequencies supported by the scan chains. However, these methods rely on Uni-Directional Signaling (UDS), in which a chip terminal (pin or a TSV) can either be used to transmit or receive data at a given time. This requires that at least two chip terminals are available at every die interface (Tester-Die or Die-Die) to form a single test channel. In this paper, we propose Simultaneous Bi-Directional Signaling (SBS), which allows a chip terminal to be used simultaneously to send and receive data, thus forming a test channel using one pin instead of two. We demonstrate how SBS can be used in conjunction with TDM to achieve reduced pin count testing while using only half the number of pins compared to conventional TDM based methods, consuming only 22.6% additional power. Alternatively, the advantage could be manifested as a test time reduction by utilizing all available test channels, allowing more parallelism and test time reduction down to half compared to UDS-based TDM. Experiments using 45nm technology suggest that the proposed method can operate at up to 1.2 GHz test clock for a stack of 3-dies, whereas for higher frequencies, a binary-weighted transmitter is proposed capable of up to 2.46 GHz test clock.
- Open Access
- 3 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
- Vol. 39 (12) , 5225-5237
Test Time Reduction of 3-D Stacked ICs Using Ternary Coded Simultaneous Bidirectional Signaling in Parallel Test Ports
In order to meet the increasing demand for more performance with reduced power consumption and chip formfactor, semiconductor manufacturing is moving towards 3D Stacked Integrated Circuits (SIC). One of the challenges in bringing this technology into realization is the complicated test accessibility requirements of 3D chips, which apart from having adequate defect coverage, should also have minimal test time. A major limiting factor in test time improvement of ICs is the number of chip terminals, such as pins or Through Silicon Vias (TSVs) available for bulk vector transport in testing. In the conventional design, a chip terminal is only used to either send or receive data at any given time. In this paper, a test accessibility architecture based on ternary encoded Simultaneous Bi-Directional Signaling (SBS), intended for use in parallel Test Access Mechanism (TAM) in System on Chip (SoC) based designs, is proposed. This method enables the use of chip terminals to simultaneously send and receive test vectors, effectively doubling the per-pin efficiency during testing. Experiments show that this technique reduces the Overall Test Time (OTT) by up to 53.6% as compared to conventional TAM design methods.
- 3 March 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
- Vol. 39 (12) , 5225-5237
Open AccessTest Time Reduction of 3-D Stacked ICs Using Ternary Coded Simultaneous Bidirectional Signaling in Parallel Test Ports
In order to meet the increasing demand for more performance with reduced power consumption and chip formfactor, semiconductor manufacturing is moving towards 3D Stacked Integrated Circuits (SIC). One of the challenges in bringing this technology into realization is the complicated test accessibility requirements of 3D chips, which apart from having adequate defect coverage, should also have minimal test time. A major limiting factor in test time improvement of ICs is the number of chip terminals, such as pins or Through Silicon Vias (TSVs) available for bulk vector transport in testing. In the conventional design, a chip terminal is only used to either send or receive data at any given time. In this paper, a test accessibility architecture based on ternary encoded Simultaneous Bi-Directional Signaling (SBS), intended for use in parallel Test Access Mechanism (TAM) in System on Chip (SoC) based designs, is proposed. This method enables the use of chip terminals to simultaneously send and receive test vectors, effectively doubling the per-pin efficiency during testing. Experiments show that this technique reduces the Overall Test Time (OTT) by up to 53.6% as compared to conventional TAM design methods.