Zhikui Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zhikui Wang has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Di Feng
Department of Civil and Transportation Engineering, Hohai University, Nanjing 210098, China
3 shared publications - Yuan Wang
Department of Water Conservancy and Hydropower Engineering, Hohai University, Nanjing 210098, China
2 shared publications - Changbin Yan
School of Civil Engineering, Zhengzhou University, Zhengzhou, China
1 shared publication - Chengcheng Peng
College of Civil and Transportation Engineering, Hohai University, Nanjing 210098, China
1 shared publication Di Feng
College of Civil and Transportation Engineering, Hohai University, Nanjing 210098, China
1 shared publication- Gaoliu Li
SGIDI Engineering Consulting (Group) Co., Ltd, Shanghai, China
1 shared publication
Latest Publications
- Open Access
- 13 September 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (9) , 366
Evolutionary Characteristics and Mesoscopic Mechanisms of the Effective Stress Coefficient in Rock Fractures Under Complex Stress Paths
Accurately evaluating the effective stress coefficient () of rock fractures under hydro-mechanical (HM) coupling is paramount for assessing the stability of fractured rock in deep underground engineering. This study conducted triaxial HM tests under varying normal stresses and multi-stage fluid pressures on marble fractures from a deep-buried water transport tunnel. Coupled with numerical simulations, the dynamic evolution and mesoscopic physical mechanisms of under complex stress paths were elucidated. Results demonstrate that is highly stress-dependent and generally less than 0.4 for smooth marble fractures. Under low normal stress, increases approximately linearly with elevated fluid pressure. Conversely, under high normal stress, exhibits low sensitivity to fluid pressure variations until surpassing a critical threshold (10–12 MPa), after which it manifests a pronounced exponential increase. Mesoscopic analysis reveals that severe contact occlusion induced by high normal stress restricts fluid permeation, leading to a heterogeneous fluid pressure distribution. This heterogeneity restricts the applicability of the traditional effective stress principle under extreme conditions. Once fluid pressure crosses the threshold, a “wedging effect” triggered by high-pressure fluid forces rapid failure of contact spots, causing a precipitous reduction in the contact area ratio (). This contact state evolution constitutes the physical essence underlying the exponential surge of . Based on experimental and inverted data, an improved empirical model for fracture effective stress was established, incorporating the coupled influences of normal stress and fluid pressure. This model possesses explicit physical significance, providing a scientific theoretical basis for evaluating surrounding rock stability in deep-buried tunnels.- 13 September 2026
- Published by MDPI AG in Geosciences
- Vol. 16 (9) , 366
Open AccessEvolutionary Characteristics and Mesoscopic Mechanisms of the Effective Stress Coefficient in Rock Fractures Under Complex Stress Paths
Accurately evaluating the effective stress coefficient () of rock fractures under hydro-mechanical (HM) coupling is paramount for assessing the stability of fractured rock in deep underground engineering. This study conducted triaxial HM tests under varying normal stresses and multi-stage fluid pressures on marble fractures from a deep-buried water transport tunnel. Coupled with numerical simulations, the dynamic evolution and mesoscopic physical mechanisms of under complex stress paths were elucidated. Results demonstrate that is highly stress-dependent and generally less than 0.4 for smooth marble fractures. Under low normal stress, increases approximately linearly with elevated fluid pressure. Conversely, under high normal stress, exhibits low sensitivity to fluid pressure variations until surpassing a critical threshold (10–12 MPa), after which it manifests a pronounced exponential increase. Mesoscopic analysis reveals that severe contact occlusion induced by high normal stress restricts fluid permeation, leading to a heterogeneous fluid pressure distribution. This heterogeneity restricts the applicability of the traditional effective stress principle under extreme conditions. Once fluid pressure crosses the threshold, a “wedging effect” triggered by high-pressure fluid forces rapid failure of contact spots, causing a precipitous reduction in the contact area ratio (). This contact state evolution constitutes the physical essence underlying the exponential surge of . Based on experimental and inverted data, an improved empirical model for fracture effective stress was established, incorporating the coupled influences of normal stress and fluid pressure. This model possesses explicit physical significance, providing a scientific theoretical basis for evaluating surrounding rock stability in deep-buried tunnels. - 30 January 2026
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 85 (2) , 109
Evaluation of TBM tunneling efficiency based on a new rock brittleness index considering energy conversion
- 30 January 2026
- Published by Springer Nature in Bulletin of Engineering Geology and the Environment
- Vol. 85 (2) , 109
Evaluation of TBM tunneling efficiency based on a new rock brittleness index considering energy conversion
- Open Access
Experimental Study on Performance of Modified Cement-Based Building Materials under High-Water-Pressure Surrounding Rock Environment
Traditional cement-based grouting materials have good reinforcement and anti-seepage effects on the surrounding rock under normal conditions, but the grouting effect is not ideal due to problems such as a long setting time, a low stone ratio, and poor crack resistance under high water pressure and in a dynamic water environment. In this study, we aimed to improve the physical properties, chemical properties, and microstructure of a cement-based slurry by forming a hydrogel through its chemical crosslinking with polyvinyl alcohol and boric acid as modifiers for the purpose of improving the permeability resistance of the surrounding rock grouting under high-water-pressure conditions, which can expand the function of traditional building materials. The grouting effect of the modified cementitious material on the surrounding rock was analyzed through indoor tests, the SEM testing of the performance of the modified slurry, the numerical calculation of the seepage field, and the application of the modified slurry in combination with the actual project to verify the water-plugging effect. The research findings demonstrate that (1) the additives boric acid and PVA can significantly speed up the slurry gel time, and the gel time can be controlled within 2–20 min to meet the specification requirements. (2) At a velocity of moving water > 1 m/s, the retention of the solidified modified slurry stone body reaches more than 80%. According to the SEM analysis, the structure of the solidified modified slurry stone body is dense and has good impermeability. (3) According to the numerical calculation analysis, the modified slurry can effectively change the seepage field of the surrounding rock and improve its seepage resistance. The water pressure outside the lining is reduced by 47%, 31%, and 22%, respectively, compared with no slurry, the pure cement slurry, and cement–water-glass grouting, and the indoor test and numerical simulation conclusions are consistent.
Open AccessExperimental Study on Performance of Modified Cement-Based Building Materials under High-Water-Pressure Surrounding Rock Environment
Traditional cement-based grouting materials have good reinforcement and anti-seepage effects on the surrounding rock under normal conditions, but the grouting effect is not ideal due to problems such as a long setting time, a low stone ratio, and poor crack resistance under high water pressure and in a dynamic water environment. In this study, we aimed to improve the physical properties, chemical properties, and microstructure of a cement-based slurry by forming a hydrogel through its chemical crosslinking with polyvinyl alcohol and boric acid as modifiers for the purpose of improving the permeability resistance of the surrounding rock grouting under high-water-pressure conditions, which can expand the function of traditional building materials. The grouting effect of the modified cementitious material on the surrounding rock was analyzed through indoor tests, the SEM testing of the performance of the modified slurry, the numerical calculation of the seepage field, and the application of the modified slurry in combination with the actual project to verify the water-plugging effect. The research findings demonstrate that (1) the additives boric acid and PVA can significantly speed up the slurry gel time, and the gel time can be controlled within 2–20 min to meet the specification requirements. (2) At a velocity of moving water > 1 m/s, the retention of the solidified modified slurry stone body reaches more than 80%. According to the SEM analysis, the structure of the solidified modified slurry stone body is dense and has good impermeability. (3) According to the numerical calculation analysis, the modified slurry can effectively change the seepage field of the surrounding rock and improve its seepage resistance. The water pressure outside the lining is reduced by 47%, 31%, and 22%, respectively, compared with no slurry, the pure cement slurry, and cement–water-glass grouting, and the indoor test and numerical simulation conclusions are consistent.
- Open Access
Effect of Leaching Behavior on the Geometric and Hydraulic Characteristics of Concrete Fracture
The leaching of material from concrete fracture surfaces has an impact on the structural concrete in service, but the number of studies that consider the effect of the coupling of the leaching, fracture geometry and hydraulic processes on concrete fractures is insufficient. In this study, a series of experiments was conducted, and a leaching model proposed, to investigate the mechanism of leaching behavior on the geometric and hydraulic characteristics of concrete fractures. Following the leaching experiment, the evolution of fracture geometric characteristics was observed by a three-dimensional (3D) laser scanning technique, finding that the fracture produces residual leached depth and local uneven leaching, which results in a decrease in roughness. The hydraulic characteristics were then investigated by permeability tests, and it was found that the fracture hydraulic aperture and permeability increase monotonically with leaching time. A simulation of fluid flow in a numerical fracture revealed the effect of residual leached depth and a decrease in roughness on the hydraulic characteristics. Finally, based on the analysis of the chemical composition of the leaching solution, a leaching model of concrete rough fracture surface is proposed and the mechanism of leaching behavior is discussed. These new findings are useful for the understanding of the development of leaching, local to concrete fracture surfaces.
Open AccessEffect of Leaching Behavior on the Geometric and Hydraulic Characteristics of Concrete Fracture
The leaching of material from concrete fracture surfaces has an impact on the structural concrete in service, but the number of studies that consider the effect of the coupling of the leaching, fracture geometry and hydraulic processes on concrete fractures is insufficient. In this study, a series of experiments was conducted, and a leaching model proposed, to investigate the mechanism of leaching behavior on the geometric and hydraulic characteristics of concrete fractures. Following the leaching experiment, the evolution of fracture geometric characteristics was observed by a three-dimensional (3D) laser scanning technique, finding that the fracture produces residual leached depth and local uneven leaching, which results in a decrease in roughness. The hydraulic characteristics were then investigated by permeability tests, and it was found that the fracture hydraulic aperture and permeability increase monotonically with leaching time. A simulation of fluid flow in a numerical fracture revealed the effect of residual leached depth and a decrease in roughness on the hydraulic characteristics. Finally, based on the analysis of the chemical composition of the leaching solution, a leaching model of concrete rough fracture surface is proposed and the mechanism of leaching behavior is discussed. These new findings are useful for the understanding of the development of leaching, local to concrete fracture surfaces.
- Open Access
- 1 January 2021
- Published by Wiley in Advances in Civil Engineering
- Vol. 2021 (1)
Wedge Instability Model Improvement of Shield Tunnel Excavation Face under Inclined Surface
In the process of the underground tunnel excavation, a kind of geological condition Necking Region is often encountered. The ground surface inclines very fast, which also leads to the increase of Earth pressure on the excavation face. The determination of the excavation face support pressure is essential to solve the active Earth pressure when the shield passes through the Necking Region. In this paper, based on Horn’s wedge model, considering the influence of surface dip angle on excavation face support pressure, the traditional wedge model was improved. The analytical solution of the ultimate support pressure for the active failure of shield excavation face was derived. To evaluate the quality of the model, the theoretical model was compared with the ultimate bearing pressure of the horizontal surface test. The influence of the ultimate support pressure on the parameters of Nc, Nγ, and Nq was consistent with the results of finite element simulation and existing theories, which verified the rationality of the model. The stability of the excavation face of the Heyan road river crossing tunnel was analyzed by using the improved wedge model. The results show that the mud support pressure considering the slope angle was 36 kPa higher than that without considering the slope angle.
- 1 January 2021
- Published by Wiley in Advances in Civil Engineering
- Vol. 2021 (1)
Open AccessWedge Instability Model Improvement of Shield Tunnel Excavation Face under Inclined Surface
In the process of the underground tunnel excavation, a kind of geological condition Necking Region is often encountered. The ground surface inclines very fast, which also leads to the increase of Earth pressure on the excavation face. The determination of the excavation face support pressure is essential to solve the active Earth pressure when the shield passes through the Necking Region. In this paper, based on Horn’s wedge model, considering the influence of surface dip angle on excavation face support pressure, the traditional wedge model was improved. The analytical solution of the ultimate support pressure for the active failure of shield excavation face was derived. To evaluate the quality of the model, the theoretical model was compared with the ultimate bearing pressure of the horizontal surface test. The influence of the ultimate support pressure on the parameters of Nc, Nγ, and Nq was consistent with the results of finite element simulation and existing theories, which verified the rationality of the model. The stability of the excavation face of the Heyan road river crossing tunnel was analyzed by using the improved wedge model. The results show that the mud support pressure considering the slope angle was 36 kPa higher than that without considering the slope angle.
- 2 April 2020
- Published by Springer Nature
- p. 293-300
Software Design of Online Monitoring System of Large Linear Vibrating Screen Fault Diagnosis
- 2 April 2020
- Published by Springer Nature
- p. 293-300
Software Design of Online Monitoring System of Large Linear Vibrating Screen Fault Diagnosis
- 25 July 2018
- Published by Taylor & Francis
- p. 202-249
Cross-Layer Power Management