Thorsten Döhring
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Thorsten Döhring has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- Manfred Stollenwerk
Aschaffenburg University of Applied Sciences, Aschaffenburg, Germany
5 shared publications Johannes Stadtmüller
3 shared publications- Dominic Freudenmann
German Aerospace Center (DLR), Institute of Space Propulsion, Im Langen Grund, 74239 Hardthausen, Germany
2 shared publications - Michael Krumrey
Physikalisch-Technische Bundesanstalt (PTB), Abbestrasse 2-12, 10587 Berlin, Germany
2 shared publications - Nicole Röcke
Institute of Space Propulsion—Chemical Propellant Technology, Department, German Aerospace Center (DLR), Hardthausen, Germany
2 shared publications Adolf Inneman
Czech Technical Univ. in Prague (Czech Republic)
1 shared publication
Latest Publications
- Open Access
- 19 May 2026
- Published by EDP Sciences in Journal of the European Optical Society-Rapid Publications
- Vol. 22 (1) , 41
Verifying optical simulations for infrared curing of powder coatings
In line with the energy transition, it is desirable to replace fossil fuels in the curing process of industrial powder coatings. Infrared heating is the considered method here. Near Infra Red-emitter arrangement in the reflective heating chamber, their geometry and the dwell time of the components are crucial for a successful and efficient process. Process optimization has to consider the optical parameter variation of the powder coating during the procedure. Measurements in the NAPUBEST (“ Na chhaltige Pu lver bes chichtungs- T echnologie”: sustainable powder coating technology) prototype are compared with optical simulations of the setup to get the simulation parameters in agreement with reality and to provide a foundation for the layout of industrial processes.
- 19 May 2026
- Published by EDP Sciences in Journal of the European Optical Society-Rapid Publications
- Vol. 22 (1) , 41
Open AccessVerifying optical simulations for infrared curing of powder coatings
In line with the energy transition, it is desirable to replace fossil fuels in the curing process of industrial powder coatings. Infrared heating is the considered method here. Near Infra Red-emitter arrangement in the reflective heating chamber, their geometry and the dwell time of the components are crucial for a successful and efficient process. Process optimization has to consider the optical parameter variation of the powder coating during the procedure. Measurements in the NAPUBEST (“ Na chhaltige Pu lver bes chichtungs- T echnologie”: sustainable powder coating technology) prototype are compared with optical simulations of the setup to get the simulation parameters in agreement with reality and to provide a foundation for the layout of industrial processes.
- Open Access
- 30 October 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 92, 852-864
Overall alkaline water electrolysis over active, stable, low loading iridium catalysts sputtered on nickel foam
- 30 October 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 92, 852-864
Open AccessOverall alkaline water electrolysis over active, stable, low loading iridium catalysts sputtered on nickel foam
- 2 October 2024
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 50 (11) , 5385-5397
Microstructure of highly effective platinum–iridium alloys as catalysts for hydrogen peroxide decomposition
- 2 October 2024
- Published by Springer Nature in Research on Chemical Intermediates
- Vol. 50 (11) , 5385-5397
Microstructure of highly effective platinum–iridium alloys as catalysts for hydrogen peroxide decomposition
- 17 October 2022
- Published by Springer Nature
- p. 65-79
Hybride Hochschulausbildung als erfolgreiches Sales-Enablement-Training
- 17 October 2022
- Published by Springer Nature
- p. 65-79
Hybride Hochschulausbildung als erfolgreiches Sales-Enablement-Training
- Open Access
- 13 October 2022
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 266, 13010
Characterization of a lobster-eye type X-ray telescope
Lobster-eye type X-ray telescopes use reflecting plano mirrors under grazing incidence and can observe a large field of view. As part of a Bavarian-Czech cooperation, two telescopes were build, equipped with mirrors coated with gold and iridium. Their X-ray characterization was carried out at the PANTER test facility, which simulates parallel starlight incident on the telescopes. The telescopes have an angular resolution of about 4 arc minutes in X-rays and a focal length of about 2 meters. The used X-ray mirrors reflect and focus visible light as well; their functionality in the optical regime was checked in laboratory tests. Now another test campaign will be carried out to examine the telescope resolution for real objects of the visible night sky and the imaging properties for star constellations.
- 13 October 2022
- Published by EDP Sciences in EPJ Web of Conferences
- Vol. 266, 13010
Open AccessCharacterization of a lobster-eye type X-ray telescope
Lobster-eye type X-ray telescopes use reflecting plano mirrors under grazing incidence and can observe a large field of view. As part of a Bavarian-Czech cooperation, two telescopes were build, equipped with mirrors coated with gold and iridium. Their X-ray characterization was carried out at the PANTER test facility, which simulates parallel starlight incident on the telescopes. The telescopes have an angular resolution of about 4 arc minutes in X-rays and a focal length of about 2 meters. The used X-ray mirrors reflect and focus visible light as well; their functionality in the optical regime was checked in laboratory tests. Now another test campaign will be carried out to examine the telescope resolution for real objects of the visible night sky and the imaging properties for star constellations.
- 15 July 2022
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12298, 39-46
Environmentally stable iridium mirror coatings for the infrared spectral range
Highly reflective metal coatings are essential for numerous optical elements. Established mirror coatings made of silver (Ag) and gold (Au) offer high and broadband self-reflection in the infrared (IR) spectral range but are susceptible to environmental influences and mechanical stress without suitable protective layers. In the long-wavelength spectral range, in particular, the absorption bands of these protective layers partially reduce the high mirror reflectivity again. However, the noble metal iridium (Ir) is hard, extremely dense, and thermally, mechanically, and chemically stable. Iridium provides a similarly high reflectivity in the mid (MIR) and far-infrared (FIR) spectral range, as silver and gold, and high resistance to environmental influences - even without protective layers. In this paper, the different deposition processes, as well as the optical and structural properties of iridium mirror coatings fabricated by atomic layer deposition (ALD) and by magnetron sputtering (MS), are presented and compared with each other. The complex refractive indices for ALD and MS deposited iridium mirror coatings were determined for wavelengths from 200 nm to 20 μm, complementing the existing literature values. We demonstrate that iridium mirror coatings offer a high and broadband reflectivity from the mid to far-infrared spectral range. In contrast to established – protected – silver and gold mirror coatings, the iridium coatings are environmentally durable and thermally stable up to 600°C, even without protective layers. Therefore, as an interesting mirror coating material, iridium has the potential for special applications in infrared astronomy and probably also for industrial instruments.
- 15 July 2022
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12298, 39-46
Environmentally stable iridium mirror coatings for the infrared spectral range
Highly reflective metal coatings are essential for numerous optical elements. Established mirror coatings made of silver (Ag) and gold (Au) offer high and broadband self-reflection in the infrared (IR) spectral range but are susceptible to environmental influences and mechanical stress without suitable protective layers. In the long-wavelength spectral range, in particular, the absorption bands of these protective layers partially reduce the high mirror reflectivity again. However, the noble metal iridium (Ir) is hard, extremely dense, and thermally, mechanically, and chemically stable. Iridium provides a similarly high reflectivity in the mid (MIR) and far-infrared (FIR) spectral range, as silver and gold, and high resistance to environmental influences - even without protective layers. In this paper, the different deposition processes, as well as the optical and structural properties of iridium mirror coatings fabricated by atomic layer deposition (ALD) and by magnetron sputtering (MS), are presented and compared with each other. The complex refractive indices for ALD and MS deposited iridium mirror coatings were determined for wavelengths from 200 nm to 20 μm, complementing the existing literature values. We demonstrate that iridium mirror coatings offer a high and broadband reflectivity from the mid to far-infrared spectral range. In contrast to established – protected – silver and gold mirror coatings, the iridium coatings are environmentally durable and thermally stable up to 600°C, even without protective layers. Therefore, as an interesting mirror coating material, iridium has the potential for special applications in infrared astronomy and probably also for industrial instruments.
- 18 April 2021
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11776, 1177607-3
Characterisation of X-ray mirrors based on chromium-iridium tri-layer coatings
Iridium-based layer systems are highly effective mirror coatings for space-born X-ray telescopes. During the recent years, Aschaffenburg University of Applied Sciences and its partners developed stress compensated chromium-iridium coatings for such astronomical applications, using chromium as an adhesive layer between iridium reflective layer and mirror substrate. However, there was room for improvement: To overcome the disturbing reflectivity reduction of the iridium absorption edge around 2 keV photon energy, thin overcoat layers of chromium are applied in addition now. This layer system has been analyzed by atomic force microscopy and transmission electron microscopy images. Furthermore, the reflectivity of such innovative X-ray mirrors based on chromium-iridium tri-layer coatings was recently measured at PTB's four-crystal monochromator beamline at the synchrotron radiation facility BESSY II. The experimental results, obtained for photon energies between 1.9 keV and 11 keV at two grazing incidence angles (0.6 degree and 0.9 degree) and their comparison with corresponding simulations are presented in this contribution. When compared to simulations of pure iridium coatings, a significantly higher reflectivity was achieved especially in the soft X-ray regime between 2 keV and 4 keV. Such chromium-iridium tri-layer coatings have high potential to increase the effective area for X-ray telescopes in Lobster Eye Design, for Wolter-I type X-ray optics, and for silicon pore optics as considered for the ATHENA telescope of the European Space Agency.
- 18 April 2021
- Published by SPIE-Intl Soc Optical Eng
- Vol. 11776, 1177607-3
Characterisation of X-ray mirrors based on chromium-iridium tri-layer coatings
Iridium-based layer systems are highly effective mirror coatings for space-born X-ray telescopes. During the recent years, Aschaffenburg University of Applied Sciences and its partners developed stress compensated chromium-iridium coatings for such astronomical applications, using chromium as an adhesive layer between iridium reflective layer and mirror substrate. However, there was room for improvement: To overcome the disturbing reflectivity reduction of the iridium absorption edge around 2 keV photon energy, thin overcoat layers of chromium are applied in addition now. This layer system has been analyzed by atomic force microscopy and transmission electron microscopy images. Furthermore, the reflectivity of such innovative X-ray mirrors based on chromium-iridium tri-layer coatings was recently measured at PTB's four-crystal monochromator beamline at the synchrotron radiation facility BESSY II. The experimental results, obtained for photon energies between 1.9 keV and 11 keV at two grazing incidence angles (0.6 degree and 0.9 degree) and their comparison with corresponding simulations are presented in this contribution. When compared to simulations of pure iridium coatings, a significantly higher reflectivity was achieved especially in the soft X-ray regime between 2 keV and 4 keV. Such chromium-iridium tri-layer coatings have high potential to increase the effective area for X-ray telescopes in Lobster Eye Design, for Wolter-I type X-ray optics, and for silicon pore optics as considered for the ATHENA telescope of the European Space Agency.
- Open Access
- 1 March 2021
- Published by Springer Nature in Journal of Materials Science
- Vol. 56 (16) , 9974-9984
Sputtered highly effective iridium catalysts: a new approach for green satellite propulsion
This work demonstrated the large potential of sputtered iridium metal for catalytic reactions shown by the example of decomposition of hydrogen peroxide (H2O2) for space propulsion systems. For this purpose, iridium was coated onto Al2O3 pellets by a sputter process under varied process parameters. Depending on previously selected parameters, the obtained metal-loaded pellets offer closed- and/or open-shell structures. Catalytic productivity of these first-generation iridium-sputtered catalysts was estimated in laboratory experiments and compared to platinum-loaded pellets. Under optimized sputter-process conditions, the reactivity is significantly improved compared to the platinum-impregnated pellets. The better catalytic productivity can be explained by the increased active surface area of the iridium layers on the pellets. The surface morphology and the microstructure of the iridium coating can be actively controlled by the sputter pressure. The results are in accordance with the sputtering process pressure tendency described by the Thornton Structure–Zone Model. Graphical abstract
- 1 March 2021
- Published by Springer Nature in Journal of Materials Science
- Vol. 56 (16) , 9974-9984
Open AccessSputtered highly effective iridium catalysts: a new approach for green satellite propulsion
This work demonstrated the large potential of sputtered iridium metal for catalytic reactions shown by the example of decomposition of hydrogen peroxide (H2O2) for space propulsion systems. For this purpose, iridium was coated onto Al2O3 pellets by a sputter process under varied process parameters. Depending on previously selected parameters, the obtained metal-loaded pellets offer closed- and/or open-shell structures. Catalytic productivity of these first-generation iridium-sputtered catalysts was estimated in laboratory experiments and compared to platinum-loaded pellets. Under optimized sputter-process conditions, the reactivity is significantly improved compared to the platinum-impregnated pellets. The better catalytic productivity can be explained by the increased active surface area of the iridium layers on the pellets. The surface morphology and the microstructure of the iridium coating can be actively controlled by the sputter pressure. The results are in accordance with the sputtering process pressure tendency described by the Thornton Structure–Zone Model. Graphical abstract
- 31 May 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10235, 1023505-1023505-7
Study of lobster eye optics with iridium coated x-ray mirrors for a rocket experiment
- 31 May 2017
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10235, 1023505-1023505-7
Study of lobster eye optics with iridium coated x-ray mirrors for a rocket experiment
- 1 April 1994
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 33 (4) , 1314-1322
Electron-beam-deposited Mo/Si and MoxSiy/Si multilayer x-ray mirrors and gratings
For the wavelength region above the Si-L edge normal incidence, soft x-ray mirrors are produced with peak reflectivities close to 60%. The multilayer systems consist of molybdenum and silicon and are fabricated by electron beam evaporation in ultrahigh vacuum. A smoothing of the boundaries, and thereby a drastic enhancement of the reflectivity, is obtained by thermal treatment of the multilayer systems during growth. The thermal stability of the multilayer stacks could be improved considerably up to 850° C by mixing Mo and Si in the absorber layers and producing thus MoxSiy/Si multilayers with x and y denoting the amounts of Mo and Si in the absorber layer, respectively. First attempts are reported to produce mirrors with a bilayer thickness of 2.6 nm. An improvement in the quality of these interfaces can be obtained by bombardment with Ar+ ions. We report on normal incidence reflectivity measurements of the mirrors with synchrotron radiation and finally on the normal incidence diffraction efficiencies of a Mo/Si multilayer coated grating, for which values of 5.5% are achieved for the + 1'st and - 1'st diffraction orders.
- 1 April 1994
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 33 (4) , 1314-1322
Electron-beam-deposited Mo/Si and MoxSiy/Si multilayer x-ray mirrors and gratings
For the wavelength region above the Si-L edge normal incidence, soft x-ray mirrors are produced with peak reflectivities close to 60%. The multilayer systems consist of molybdenum and silicon and are fabricated by electron beam evaporation in ultrahigh vacuum. A smoothing of the boundaries, and thereby a drastic enhancement of the reflectivity, is obtained by thermal treatment of the multilayer systems during growth. The thermal stability of the multilayer stacks could be improved considerably up to 850° C by mixing Mo and Si in the absorber layers and producing thus MoxSiy/Si multilayers with x and y denoting the amounts of Mo and Si in the absorber layer, respectively. First attempts are reported to produce mirrors with a bilayer thickness of 2.6 nm. An improvement in the quality of these interfaces can be obtained by bombardment with Ar+ ions. We report on normal incidence reflectivity measurements of the mirrors with synchrotron radiation and finally on the normal incidence diffraction efficiencies of a Mo/Si multilayer coated grating, for which values of 5.5% are achieved for the + 1'st and - 1'st diffraction orders.