Vitor Ferreira Vieira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Vitor Ferreira Vieira has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Paulo Sérgio Martins
Pontifícia Universidade Católica de Minas Gerais, Brasil
6 shared publications - Elhadji Cheikh Talibouya Ba
Graduate Program in Mechanical Engineering, Universidade Federal de Uberlândia, Uberlândia, Brazil
5 shared publications - José Rubens Gonçalves Carneiro
Pontifícia Universidade Católica De Minas Gerais
3 shared publications - Gustavo Henrique Nazareno Fernandes
Postgraduate Program in Production Engineering, Faculty of Science and Technology, Federal University of Goiás—UFG, Aparecida de Goiânia Campus, Municipal Road, Block and Lot Area 04, Aparecida de Goiânia 74971-45, GO, Brazil
2 shared publications - Yukio Shigaki
Programa de Pós-Graduação Em Engenharia Mecânica, Federal Center for Technological Education of Minas Gerais, Belo Horizonte, Brazil
2 shared publications - Cádmo Augusto Rodrigues
Pontifícia Universidade Católica de Minas Gerais, Belo Horizonte, Brazil
1 shared publication
Latest Publications
- 15 November 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 141 (9-10) , 4951-4966
Nanoindentation test simulation of a high-speed steel substrate with DLC coating and a Berkovich indenter using a two-dimensional and three-dimensional axisymmetric simplification finite element method
- 15 November 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 141 (9-10) , 4951-4966
Nanoindentation test simulation of a high-speed steel substrate with DLC coating and a Berkovich indenter using a two-dimensional and three-dimensional axisymmetric simplification finite element method
- 24 January 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 136 (7-8) , 3709-3733
Dynamic and dimensional evaluation of robot applications in the drilling process in Al–Mg-Si 6351 T6 aluminum alloy
- 24 January 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 136 (7-8) , 3709-3733
Dynamic and dimensional evaluation of robot applications in the drilling process in Al–Mg-Si 6351 T6 aluminum alloy
- 4 May 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (11-12) , 7803-7814
Study of wear behavior and tool life in different taps during the internal threading of a nodular iron engine crankshaft
- 4 May 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 120 (11-12) , 7803-7814
Study of wear behavior and tool life in different taps during the internal threading of a nodular iron engine crankshaft
- Open Access
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 25 (1)
Study on the Tribological Behavior of Wear and Friction Coefficient on AISI M35 High-Speed Steel with and without DLC Coating
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 25 (1)
Open AccessStudy on the Tribological Behavior of Wear and Friction Coefficient on AISI M35 High-Speed Steel with and without DLC Coating
- Open Access
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 24 (2)
Investigation of the effects of skewness Rsk and kurtosis Rku on tribological behavior in a pin-on-disc test of surfaces machined by conventional milling and turning processes
Friction and wear are influenced by the surface conditions of the material, since there is deformation, segregation, generation of oxide films, among others. Roughness is an important characteristic in tribological studies, where the parameters of skewness and kurtosis have greater influence than the conventional parameters Ra and Rq. This study is aimed to investigate the influence of the parameters of skewness Rsk and Rku kurtosis on the surface of the USI AR 360 steel machining by the milling and turning processes in the pin-on-disc sliding wear test. Results showed that surfaces with the same Ra and Rq could be distinguished by the skewness parameter. Different behaviors were observed in the analysis of friction curves, where the skewness effect showed a tendency to reduce the friction coefficient. It was also observed that the feed marks orientation in relation to the sliding direction can influence the tribological behavior of the surfaces.
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 24 (2)
Open AccessInvestigation of the effects of skewness Rsk and kurtosis Rku on tribological behavior in a pin-on-disc test of surfaces machined by conventional milling and turning processes
Friction and wear are influenced by the surface conditions of the material, since there is deformation, segregation, generation of oxide films, among others. Roughness is an important characteristic in tribological studies, where the parameters of skewness and kurtosis have greater influence than the conventional parameters Ra and Rq. This study is aimed to investigate the influence of the parameters of skewness Rsk and Rku kurtosis on the surface of the USI AR 360 steel machining by the milling and turning processes in the pin-on-disc sliding wear test. Results showed that surfaces with the same Ra and Rq could be distinguished by the skewness parameter. Different behaviors were observed in the analysis of friction curves, where the skewness effect showed a tendency to reduce the friction coefficient. It was also observed that the feed marks orientation in relation to the sliding direction can influence the tribological behavior of the surfaces.