Anatolii Dovbush
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Anatolii Dovbush has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Taras Dovbush
Ternopil Ivan Pului National Technical University
5 shared publications - Anna Tson
Ternopil Ivan Pului National Technical University
2 shared publications - Nadia Khomyk2 shared publications
- Андрій Георгійович Никитюк2 shared publications
- Andrii Diachun
Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine
1 shared publication - Andrii Stanko
Тернопільський національний технічний університет імені Івана Пулюя
1 shared publication
Latest Publications
- 28 May 2026
- Published by Vinnytsia National Agrarian University in Engineering, Energy, Transport AIC
- p. 94
A THEORETICAL STUDY OF THE PROCESS OF TRIMMING BEET TOPS USING PASSIVE BLADES
Based on the principle that the potential energy of the system is equal to the external work expended during the trimming of sugar beet roots with a passive flat knife, the study substantiates the possibility of reducing the load on the working body by rationally selecting the knife installation angle relative to the axis of motion of the top-trimming unit. It has been established that changing this angle directly affects the cutting force and the length of the knife travel path in the root crown zone. Therefore, a properly selected blade angle makes it possible not only to reduce the force acting on the knife, but also to improve the quality of top removal by increasing the cutting path and ensuring more stable interaction between the blade and the root surface. Before performing the technological process of sugar beet top trimming, it is advisable to analyze the geometric parameters of the roots, primarily the average crown diameter, since this parameter determines the initial conditions for calculating the cutting force. By setting the blade thickness of the trimming device and using the established analytical dependence, the required force applied to the blade can be determined. Taking into account the strength limit of the blade material, the recommended operating speed of the unit is then calculated. At the same time, speeds that may cause resonance phenomena in the trimming device must be excluded from the acceptable range. Knowing the cutting force and the knife angle, the natural frequency of the device is determined using the proposed relationship. Further analysis of the obtained results makes it possible to identify the travel speeds at which resonance may occur. These speeds should be avoided during operation, as they can increase dynamic loads, reduce trimming quality, and accelerate wear of the working body. Thus, the proposed approach provides a consistent procedure for selecting the geometric and kinematic parameters of a passive flat knife, ensuring lower cutting resistance, improved top-trimming quality, and more reliable operation of the sugar beet harvesting unit.
- 28 May 2026
- Published by Vinnytsia National Agrarian University in Engineering, Energy, Transport AIC
- p. 94
A THEORETICAL STUDY OF THE PROCESS OF TRIMMING BEET TOPS USING PASSIVE BLADES
Based on the principle that the potential energy of the system is equal to the external work expended during the trimming of sugar beet roots with a passive flat knife, the study substantiates the possibility of reducing the load on the working body by rationally selecting the knife installation angle relative to the axis of motion of the top-trimming unit. It has been established that changing this angle directly affects the cutting force and the length of the knife travel path in the root crown zone. Therefore, a properly selected blade angle makes it possible not only to reduce the force acting on the knife, but also to improve the quality of top removal by increasing the cutting path and ensuring more stable interaction between the blade and the root surface. Before performing the technological process of sugar beet top trimming, it is advisable to analyze the geometric parameters of the roots, primarily the average crown diameter, since this parameter determines the initial conditions for calculating the cutting force. By setting the blade thickness of the trimming device and using the established analytical dependence, the required force applied to the blade can be determined. Taking into account the strength limit of the blade material, the recommended operating speed of the unit is then calculated. At the same time, speeds that may cause resonance phenomena in the trimming device must be excluded from the acceptable range. Knowing the cutting force and the knife angle, the natural frequency of the device is determined using the proposed relationship. Further analysis of the obtained results makes it possible to identify the travel speeds at which resonance may occur. These speeds should be avoided during operation, as they can increase dynamic loads, reduce trimming quality, and accelerate wear of the working body. Thus, the proposed approach provides a consistent procedure for selecting the geometric and kinematic parameters of a passive flat knife, ensuring lower cutting resistance, improved top-trimming quality, and more reliable operation of the sugar beet harvesting unit.
- Open Access
- 27 March 2026
- Published by Central Ukrainian National Technical University in Central Ukrainian Scientific Bulletin. Technical Sciences
- No. 13(44)
Розроблення гвинтових робочих органів змішувачів
У статті проведено структурно-схемний синтез гвинтових робочих органів змішувальних агрегатів. Шляхом експертного аналізу факторів, що детермінують ефективність гомогенізації, ідентифіковано ключові морфологічні ознаки та встановлено системні взаємозв'язки між ними. На основі результатів системного аналізу розроблено морфологічну матрицю конструктивних параметрів, яка стала теоретичним базисом для побудови структурно-функціональної моделі механічної системи «гвинтовий робочий орган змішувача». Визначено, що функціональні можливості гвинтових робочих органів змішувачів визначаються їх компонувальною схемою. Зокрема одиничне використання реалізує суміщення процесів переміщення та змішування матеріалу, а групове, за умови застосування декількох гвинтових робочих органів змішувачів із протилежним або різнонаправленим вектором руху в межах одного технічного пристрою, забезпечує інтенсифікацію виключно змішувальної функції. В ході реалізації структурно-схемного синтезу було виокремлено такі домінуючі морфологічні ознаки конструктивних елементів гвинтових робочих органів змішувачів: конструкція гвинта; жорсткість гвинта; комбінація гвинта; за кількістю спіралей; крок гвинта; діаметр гвинта; профіль спіралі; тип гвинта; спосіб кріплення елементів. Застосований підхід дозволив згенерувати низку високоефективних конструктивних рішень, спрямованих на інтенсифікацію процесу змішування. До них належать робочі органи з додатковими елементами, лопатеві з регульованими та нерегульованими отворами просипання, пружно-еластичні та безвальний. Наукова новизна та практична значущість розробок підтверджена 9 патентами України на корисну модель та 2 заявками на отримання охоронних документів.
- 27 March 2026
- Published by Central Ukrainian National Technical University in Central Ukrainian Scientific Bulletin. Technical Sciences
- No. 13(44)
Open AccessРозроблення гвинтових робочих органів змішувачів
У статті проведено структурно-схемний синтез гвинтових робочих органів змішувальних агрегатів. Шляхом експертного аналізу факторів, що детермінують ефективність гомогенізації, ідентифіковано ключові морфологічні ознаки та встановлено системні взаємозв'язки між ними. На основі результатів системного аналізу розроблено морфологічну матрицю конструктивних параметрів, яка стала теоретичним базисом для побудови структурно-функціональної моделі механічної системи «гвинтовий робочий орган змішувача». Визначено, що функціональні можливості гвинтових робочих органів змішувачів визначаються їх компонувальною схемою. Зокрема одиничне використання реалізує суміщення процесів переміщення та змішування матеріалу, а групове, за умови застосування декількох гвинтових робочих органів змішувачів із протилежним або різнонаправленим вектором руху в межах одного технічного пристрою, забезпечує інтенсифікацію виключно змішувальної функції. В ході реалізації структурно-схемного синтезу було виокремлено такі домінуючі морфологічні ознаки конструктивних елементів гвинтових робочих органів змішувачів: конструкція гвинта; жорсткість гвинта; комбінація гвинта; за кількістю спіралей; крок гвинта; діаметр гвинта; профіль спіралі; тип гвинта; спосіб кріплення елементів. Застосований підхід дозволив згенерувати низку високоефективних конструктивних рішень, спрямованих на інтенсифікацію процесу змішування. До них належать робочі органи з додатковими елементами, лопатеві з регульованими та нерегульованими отворами просипання, пружно-еластичні та безвальний. Наукова новизна та практична значущість розробок підтверджена 9 патентами України на корисну модель та 2 заявками на отримання охоронних документів.
- Open Access
- 11 December 2025
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 359 (6.1) , 194-200
ЗАСТОСУВАННЯ ТЕХНОЛОГІЧНОГО КОМПЛЕКСУ ДЛЯ АВІАЦІЙНОЇ ХІМІЧНОЇ ОБРОБКИ КУЛЬТУРНИХ РОСЛИН
The article investigates the conditions for ensuring high-performance operation of agricultural drones during the processing of crops and plantations of agricultural crops. It is established that the coincidence of the time of the technological process of processing plants with drones and the time of active operation of their batteries is mandatory. It was noted that time expenditure can be synchronized by timely recharging or replacing batteries, and for this it is necessary to use a technological complex that will perform service actions related to filling with a working pesticide solution and recharging batteries. It has been established that the correct choice of technological schemes for field cultivation is also important for the productive operation of agricultural drones. The article is devoted to the development of a design of a technological complex for aerial plant processing using agricultural drones and recommendations for synchronizing the time for performing the technological process by agricultural drones depending on the tank volume and the service life of the drone batteries. The developed service ground mobile technological device includes a platform with a system for refueling agricultural drones with working solutions of chemical preparations for treating plants, an agricultural drone fixation mechanism, a battery replacement mechanism, and a charging cradle. After filling the agrodrone's tank and replacing the discharged battery with a charged one, the mobile service automatically unhooks the drone, which takes off and moves in the desired direction to continue the technological process of aerochemical treatment of plants. Structurally, the technological complex for charging drones is safe to operate, and it can also be used to monitor the condition of the aircraft, especially its temperature, to prevent batteries from overheating.. It was noted that when using agricultural drones for chemical treatment of fields, the characteristics of the drones, the size of the fields, and the location of charging stations are important, which are proposed to be equipped with the developed technological complexes. Based on the availability of a constructive development of a technological complex for aerial chemical treatment of cultivated plants, taking into account the technological capabilities of agricultural drones and the results of research related to the time spent on performing the technological process of applying agrochemicals, the use of agricultural drones on fields of various configurations was simulated in accordance with technological schemes for field processing and existing technological complexes for servicing agricultural drones.
- 11 December 2025
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 359 (6.1) , 194-200
Open AccessЗАСТОСУВАННЯ ТЕХНОЛОГІЧНОГО КОМПЛЕКСУ ДЛЯ АВІАЦІЙНОЇ ХІМІЧНОЇ ОБРОБКИ КУЛЬТУРНИХ РОСЛИН
The article investigates the conditions for ensuring high-performance operation of agricultural drones during the processing of crops and plantations of agricultural crops. It is established that the coincidence of the time of the technological process of processing plants with drones and the time of active operation of their batteries is mandatory. It was noted that time expenditure can be synchronized by timely recharging or replacing batteries, and for this it is necessary to use a technological complex that will perform service actions related to filling with a working pesticide solution and recharging batteries. It has been established that the correct choice of technological schemes for field cultivation is also important for the productive operation of agricultural drones. The article is devoted to the development of a design of a technological complex for aerial plant processing using agricultural drones and recommendations for synchronizing the time for performing the technological process by agricultural drones depending on the tank volume and the service life of the drone batteries. The developed service ground mobile technological device includes a platform with a system for refueling agricultural drones with working solutions of chemical preparations for treating plants, an agricultural drone fixation mechanism, a battery replacement mechanism, and a charging cradle. After filling the agrodrone's tank and replacing the discharged battery with a charged one, the mobile service automatically unhooks the drone, which takes off and moves in the desired direction to continue the technological process of aerochemical treatment of plants. Structurally, the technological complex for charging drones is safe to operate, and it can also be used to monitor the condition of the aircraft, especially its temperature, to prevent batteries from overheating.. It was noted that when using agricultural drones for chemical treatment of fields, the characteristics of the drones, the size of the fields, and the location of charging stations are important, which are proposed to be equipped with the developed technological complexes. Based on the availability of a constructive development of a technological complex for aerial chemical treatment of cultivated plants, taking into account the technological capabilities of agricultural drones and the results of research related to the time spent on performing the technological process of applying agrochemicals, the use of agricultural drones on fields of various configurations was simulated in accordance with technological schemes for field processing and existing technological complexes for servicing agricultural drones.
- 29 September 2025
- Published by Central Ukrainian National Technical University in Central Ukrainian Scientific Bulletin. Technical Sciences
- Vol. 1 (12(43))
Synthesis of Twin-Shaft Screw Conveyor Mixers
Ivan Hevko, Professor, Doctor of Technical Sciences, Professor of the Department of Automobiles, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000- 0001-5170-0857, e-mail: gevkoivan1@ukr.net Roman Rohatynskyi, Professor, Doctor of Technical Sciences, Professor of the Department of Automobiles, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0001-8536-4599, e-mail: rogatynskyi@gmail.com Andrii Diachun, Associate Professor, PhD in Technical Sciences (Candidate of Technical Sciences), Associate Professor of the Department of Mechanical Engineering Technologies, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0003-1354-9468, e-mail: dyachun_andriy@ukr.net Taras Dovbush, Associate Professor, PhD in Technical Sciences (Candidate of Technical Sciences), Associate Professor of the Department of Technical Mechanics and Agricultural Machinery, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0002-8354- 7276, e-mail: tarasdowbush@gmail.com Anatolii Dovbush, Senior Lecturer of the Department of Technical Mechanics and Agricultural Machinery, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0001-6656-9150, e-mail: anatoliydowbush@gmail.com Andrii Nykytiuk, PhD student in Industrial Mechanical Engineering, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0009-0006-9408-228X, e-mail: knowledgebasis@gmail.com. Twin-shaft screw conveyors are often used to move piece goods, especially in conveyor lines in the food industry when filling various containers, but are also used to transport bulk materials. However, they are also widely used as mixers of loose and viscous materials as twin-shaft screw conveyors-mixers. Therefore, when using twin-shaft screw conveyors-mixers, they can act as conveyors-mixers with the functions of mixing and moving materials, or simply as mixers. To create effective designs of twin-shaft screw conveyor mixers that can provide high mixing uniformity with significant process performance and satisfactory cost, it is advisable to generate their rational variants with subsequent theoretical and experimental research and obtaining the most suitable designs for practical use. The use of morphological analysis in generating alternatives using structural- schematic synthesis ensures the receipt of a significant number of design options for technical solutions, and therefore can be fully applied in generating twin-shaft screw conveyors-mixers. To create twin-shaft screw conveyor mixers, their designs were generated using an improved synthesis method using morphological analysis, which involves the use of expert assessments and the division of individual hierarchical groups into subgroups based on the importance of individual features of structural elements. As a result of an expert assessment of the influence of various factors on the mixing operation of twin- shaft screw conveyor mixers, certain features of the structural elements of these mechanisms, as well as their interconnections, have been established. This ensured the construction of a morphological table of individual features of the structural elements of twin-shaft screw conveyors-mixers, and on its basis, accordingly, a model of the mechanical system "Twin-shaft screw conveyor-mixer". As a result of expert analysis during the implementation of the structural and schematic synthesis of twin-shaft screw conveyors-mixers, the following main morphological features of its structural elements were selected: drive: type, type of movement, direction of movement, quantity, speed; chute design; screw working elements: spiral profile, spiral design, spiral diameter, spiral location; hopper: profile, quantity, location, loading mechanism; unloading mechanism; locomotor mechanism. This made it possible to obtain a significant number of effective variants of technical solutions for twin- shaft screw conveyor mixers with various design features. In particular, design schemes of mixers with different profiles, spiral designs and arrangement of spirals relative to each other. The synthesized designs of twin-shaft screw conveyors-mixers enable extensive research of screw mixing systems with the establishment of their design and technological parameters and the selection of rational designs.
- 29 September 2025
- Published by Central Ukrainian National Technical University in Central Ukrainian Scientific Bulletin. Technical Sciences
- Vol. 1 (12(43))
Synthesis of Twin-Shaft Screw Conveyor Mixers
Ivan Hevko, Professor, Doctor of Technical Sciences, Professor of the Department of Automobiles, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000- 0001-5170-0857, e-mail: gevkoivan1@ukr.net Roman Rohatynskyi, Professor, Doctor of Technical Sciences, Professor of the Department of Automobiles, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0001-8536-4599, e-mail: rogatynskyi@gmail.com Andrii Diachun, Associate Professor, PhD in Technical Sciences (Candidate of Technical Sciences), Associate Professor of the Department of Mechanical Engineering Technologies, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0003-1354-9468, e-mail: dyachun_andriy@ukr.net Taras Dovbush, Associate Professor, PhD in Technical Sciences (Candidate of Technical Sciences), Associate Professor of the Department of Technical Mechanics and Agricultural Machinery, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0002-8354- 7276, e-mail: tarasdowbush@gmail.com Anatolii Dovbush, Senior Lecturer of the Department of Technical Mechanics and Agricultural Machinery, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0000-0001-6656-9150, e-mail: anatoliydowbush@gmail.com Andrii Nykytiuk, PhD student in Industrial Mechanical Engineering, Ternopil Ivan Puluj National Technical University, Ternopil, Ukraine, ORCID: https://orcid.org/0009-0006-9408-228X, e-mail: knowledgebasis@gmail.com. Twin-shaft screw conveyors are often used to move piece goods, especially in conveyor lines in the food industry when filling various containers, but are also used to transport bulk materials. However, they are also widely used as mixers of loose and viscous materials as twin-shaft screw conveyors-mixers. Therefore, when using twin-shaft screw conveyors-mixers, they can act as conveyors-mixers with the functions of mixing and moving materials, or simply as mixers. To create effective designs of twin-shaft screw conveyor mixers that can provide high mixing uniformity with significant process performance and satisfactory cost, it is advisable to generate their rational variants with subsequent theoretical and experimental research and obtaining the most suitable designs for practical use. The use of morphological analysis in generating alternatives using structural- schematic synthesis ensures the receipt of a significant number of design options for technical solutions, and therefore can be fully applied in generating twin-shaft screw conveyors-mixers. To create twin-shaft screw conveyor mixers, their designs were generated using an improved synthesis method using morphological analysis, which involves the use of expert assessments and the division of individual hierarchical groups into subgroups based on the importance of individual features of structural elements. As a result of an expert assessment of the influence of various factors on the mixing operation of twin- shaft screw conveyor mixers, certain features of the structural elements of these mechanisms, as well as their interconnections, have been established. This ensured the construction of a morphological table of individual features of the structural elements of twin-shaft screw conveyors-mixers, and on its basis, accordingly, a model of the mechanical system "Twin-shaft screw conveyor-mixer". As a result of expert analysis during the implementation of the structural and schematic synthesis of twin-shaft screw conveyors-mixers, the following main morphological features of its structural elements were selected: drive: type, type of movement, direction of movement, quantity, speed; chute design; screw working elements: spiral profile, spiral design, spiral diameter, spiral location; hopper: profile, quantity, location, loading mechanism; unloading mechanism; locomotor mechanism. This made it possible to obtain a significant number of effective variants of technical solutions for twin- shaft screw conveyor mixers with various design features. In particular, design schemes of mixers with different profiles, spiral designs and arrangement of spirals relative to each other. The synthesized designs of twin-shaft screw conveyors-mixers enable extensive research of screw mixing systems with the establishment of their design and technological parameters and the selection of rational designs.
- 8 December 2021
- Published by Lutsk National Technical University in СІЛЬСЬКОГОСПОДАРСЬКІ МАШИНИ
- No. 47,p. 63-72
СИНТЕЗ ГВИНТОВИХ РОБОЧИХ ОРГАНІВ ІЗ ЕЛАСТИЧНИМИ ПОВЕРХНЯМИ ТА РЕЗУЛЬТАТИ ЇХ ДОСЛІДЖЕННЯ
Гвинтові транспортери мають широке використання у різних галузях економіки, зокрема у фармацевтичній галузі, харчовій та переробній промисловості, а також у сільському господарстві. До гвинтових транспортерів висуваються вимоги, що залежать від матеріалу, який транспортується. Однією з вимог є забезпечення можливості безпечного переміщення матеріалів, що легко пошкоджуються, зокрема зернових мас. У статті представлено теоретичне обґрунтування підвищення ефективності транспортування сипких вантажів гвинтовими транспортерами. Також у статті проведено аналіз останніх досліджень за цією проблематикою. У результаті огляду джерел інформації визначена проблема, яку необхідно вирішити. Метою проведеного дослідження є визначення продуктивності транспортування сипких матеріалів та встановлення ступеня травмування зернового матеріалу розробленими гвинтовими робочими органами із еластичними поверхнями. Для пошуку нових варіантів гвинтових робочих органів із еластичними поверхнями, які б забезпечували мінімальне пошкодження зернових матеріалів, використано метод синтезу ієрархічних груп за допомогою морфологічного аналізу. Експерименти проведені для різних типів робочих органів із еластичними поверхнями: із суцільним камеро-подібним елементом; із периферійною еластичною щіткоподібною частиною; із щіткоподібним елементом. У статті запропоновані рекомендації щодо вибору частоти обертання шнеку для мінімізації пошкоджень сипких матеріалів. Також встановлено раціональний кут нахилу гвинтового робочого органу, за якого продуктивність шнекового транспортера буде максимальною. Встановлено, що продуктивність зростає із збільшенням внутрішнього діаметра кожуха шнека і частоти обертання гвинтових робочих органів у випадку горизонтального розташування.
- 8 December 2021
- Published by Lutsk National Technical University in СІЛЬСЬКОГОСПОДАРСЬКІ МАШИНИ
- No. 47,p. 63-72
СИНТЕЗ ГВИНТОВИХ РОБОЧИХ ОРГАНІВ ІЗ ЕЛАСТИЧНИМИ ПОВЕРХНЯМИ ТА РЕЗУЛЬТАТИ ЇХ ДОСЛІДЖЕННЯ
Гвинтові транспортери мають широке використання у різних галузях економіки, зокрема у фармацевтичній галузі, харчовій та переробній промисловості, а також у сільському господарстві. До гвинтових транспортерів висуваються вимоги, що залежать від матеріалу, який транспортується. Однією з вимог є забезпечення можливості безпечного переміщення матеріалів, що легко пошкоджуються, зокрема зернових мас. У статті представлено теоретичне обґрунтування підвищення ефективності транспортування сипких вантажів гвинтовими транспортерами. Також у статті проведено аналіз останніх досліджень за цією проблематикою. У результаті огляду джерел інформації визначена проблема, яку необхідно вирішити. Метою проведеного дослідження є визначення продуктивності транспортування сипких матеріалів та встановлення ступеня травмування зернового матеріалу розробленими гвинтовими робочими органами із еластичними поверхнями. Для пошуку нових варіантів гвинтових робочих органів із еластичними поверхнями, які б забезпечували мінімальне пошкодження зернових матеріалів, використано метод синтезу ієрархічних груп за допомогою морфологічного аналізу. Експерименти проведені для різних типів робочих органів із еластичними поверхнями: із суцільним камеро-подібним елементом; із периферійною еластичною щіткоподібною частиною; із щіткоподібним елементом. У статті запропоновані рекомендації щодо вибору частоти обертання шнеку для мінімізації пошкоджень сипких матеріалів. Також встановлено раціональний кут нахилу гвинтового робочого органу, за якого продуктивність шнекового транспортера буде максимальною. Встановлено, що продуктивність зростає із збільшенням внутрішнього діаметра кожуха шнека і частоти обертання гвинтових робочих органів у випадку горизонтального розташування.
- 1 January 2020
- Published by Ternopil Ivan Puluj National Technical University in Scientific journal of the Ternopil national technical university
- Vol. 100 (4) , 40-45
Improvement of prt-9 constructive system on the basis of frame elements strength balance
Analytical and experimental investigations of the most loaded elements of the base frame of PRT-9 solid organic fertilizer spreader are carried out in this paper. The residual operation life of the central beam of the paired Z-shaped profile, as well as the lateral spars of the Z-shaped cross section are determined. According to the results of studies, it was found that the residual operation life of these system elements differ significantly. In order to achieve strength uniformity of the main frame elements, it is decided to weaken the central beam by replacing the paired Z-shaped profile with a thin-walled tube of rectangular cross-section and strengthen the lateral spars by replacing Z-shaped profile with a channel profile with the same height.
- 1 January 2020
- Published by Ternopil Ivan Puluj National Technical University in Scientific journal of the Ternopil national technical university
- Vol. 100 (4) , 40-45
Improvement of prt-9 constructive system on the basis of frame elements strength balance
Analytical and experimental investigations of the most loaded elements of the base frame of PRT-9 solid organic fertilizer spreader are carried out in this paper. The residual operation life of the central beam of the paired Z-shaped profile, as well as the lateral spars of the Z-shaped cross section are determined. According to the results of studies, it was found that the residual operation life of these system elements differ significantly. In order to achieve strength uniformity of the main frame elements, it is decided to weaken the central beam by replacing the paired Z-shaped profile with a thin-walled tube of rectangular cross-section and strengthen the lateral spars by replacing Z-shaped profile with a channel profile with the same height.