Matjaž Hriberšek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Matjaž Hriberšek has a total of 167 co-authors. Here are the top co-authors by number of shared publications:
- Jure Ravnik
Faculty of Mechanical Engineering, University of Maribor, Maribor, Slovenia
35 shared publications - Paul Steinmann
Institute of Applied Mechanics, Friedrich-Alexander-Universität Erlangen-Nürnberg, Egerlandstraße 5, Erlangen, 91058, Germany
13 shared publications - Matej Zadravec
Faculty of Mechanical Engineering, University of Maribor, Smetanova Ulica 17, SI-2000 Maribor, Slovenia
12 shared publications L. Škerget
9 shared publicationsJ. Ravnik
7 shared publicationsLeopold Škerget
Faculty of Mechanical Engineering University of Maribor Smetanova ulica 17 SI-2000 Maribor Slovenia
7 shared publications
Latest Publications
- Open Access
- 28 February 2026
- Published by MDPI AG in Biomedicines
- Vol. 14 (3) , 553
Shape Matters: Computational Fluid Dynamics Analysis of Epiglottis Shape Influence on Airway Collapse in Obstructive Sleep Apnea Patients
Background: The study investigates the influence of epiglottis morphology on airflow dynamics and mechanical loading using computational fluid dynamics (CFD) in patients with obstructive sleep apnea (OSA), where the epiglottis may contribute to upper airway obstructions during sleep. Methods: A two-stage analysis was conducted: first, using a simplified airway model with two distinct epiglottis shapes (flat and curved), and second, using patient-specific 3D airway geometries derived from computed tomography (CT) scans. The simplified model enabled isolated analysis of flow-related aerodynamic forces and torques acting on the epiglottis across varying flow rates and inclination angles. Results: Results showed that the flat-shaped epiglottis was subjected to higher aerodynamic loads, particularly at lower flow rates, indicating increased susceptibility to collapse. These findings were corroborated by simulations on patient-specific 3D airway models. Conclusions: The study confirms that epiglottis morphology plays a critical role in the pathogenesis of OSA and underscores the potential of CFD for personalized assessment and treatment planning.
- 28 February 2026
- Published by MDPI AG in Biomedicines
- Vol. 14 (3) , 553
Open AccessShape Matters: Computational Fluid Dynamics Analysis of Epiglottis Shape Influence on Airway Collapse in Obstructive Sleep Apnea Patients
Background: The study investigates the influence of epiglottis morphology on airflow dynamics and mechanical loading using computational fluid dynamics (CFD) in patients with obstructive sleep apnea (OSA), where the epiglottis may contribute to upper airway obstructions during sleep. Methods: A two-stage analysis was conducted: first, using a simplified airway model with two distinct epiglottis shapes (flat and curved), and second, using patient-specific 3D airway geometries derived from computed tomography (CT) scans. The simplified model enabled isolated analysis of flow-related aerodynamic forces and torques acting on the epiglottis across varying flow rates and inclination angles. Results: Results showed that the flat-shaped epiglottis was subjected to higher aerodynamic loads, particularly at lower flow rates, indicating increased susceptibility to collapse. These findings were corroborated by simulations on patient-specific 3D airway models. Conclusions: The study confirms that epiglottis morphology plays a critical role in the pathogenesis of OSA and underscores the potential of CFD for personalized assessment and treatment planning.
- Open Access
- 31 January 2026
- Published by MDPI AG in Biomedicines
- Vol. 14 (2) , 329
Development, Fabrication and Application of a Sectioned 3D-Printed Human Nasal Cavity Model for In Vitro Nasal Spray Deposition Studies
In vitro models of the human nasal cavity are crucial for understanding the deposition dynamics of nasally administered drugs. Three-dimensional (3D) printing offers a powerful method for creating patient-specific, anatomically precise models for such experimental purposes. Background/Objectives: This study details the complete workflow for the development, design, and fabrication of a sectioned nasal cavity model intended for droplet deposition analysis of nasal sprays. Methods: A digital nasal cavity model was derived from medical imaging data and optimized for computer-aided design (CAD) operations. It was segmented into five therapeutically relevant regions: nasal vestibule, olfactory area, middle and upper turbinates, lower turbinate, and nasopharynx. Sections were 3D-printed in polypropylene for chemical compatibility, and a carbon fiber-reinforced fixation frame ensured precise alignment and airtight assembly. Results: Functional validation confirmed the model’s functional relevance through comparative deposition studies using automated actuation and high-performance liquid chromatography (HPLC) based regional quantification. Two devices with distinct spray characteristics (characterized separately by laser diffraction, plume geometry, and spray pattern imaging) were tested under varied administration conditions. The study demonstrated the model’s ability to discriminate between products, establishing a solid foundation for future investigations incorporating additional variables. Conclusions: Overall, the developed methodology provides a cost-effective and replicable platform for producing anatomically accurate, sectioned nasal cavity models. The newly developed in vitro system is well suited for detailed, region-specific analysis of nasal spray deposition, offering a valuable tool for pharmaceutical research and development.
- 31 January 2026
- Published by MDPI AG in Biomedicines
- Vol. 14 (2) , 329
Open AccessDevelopment, Fabrication and Application of a Sectioned 3D-Printed Human Nasal Cavity Model for In Vitro Nasal Spray Deposition Studies
In vitro models of the human nasal cavity are crucial for understanding the deposition dynamics of nasally administered drugs. Three-dimensional (3D) printing offers a powerful method for creating patient-specific, anatomically precise models for such experimental purposes. Background/Objectives: This study details the complete workflow for the development, design, and fabrication of a sectioned nasal cavity model intended for droplet deposition analysis of nasal sprays. Methods: A digital nasal cavity model was derived from medical imaging data and optimized for computer-aided design (CAD) operations. It was segmented into five therapeutically relevant regions: nasal vestibule, olfactory area, middle and upper turbinates, lower turbinate, and nasopharynx. Sections were 3D-printed in polypropylene for chemical compatibility, and a carbon fiber-reinforced fixation frame ensured precise alignment and airtight assembly. Results: Functional validation confirmed the model’s functional relevance through comparative deposition studies using automated actuation and high-performance liquid chromatography (HPLC) based regional quantification. Two devices with distinct spray characteristics (characterized separately by laser diffraction, plume geometry, and spray pattern imaging) were tested under varied administration conditions. The study demonstrated the model’s ability to discriminate between products, establishing a solid foundation for future investigations incorporating additional variables. Conclusions: Overall, the developed methodology provides a cost-effective and replicable platform for producing anatomically accurate, sectioned nasal cavity models. The newly developed in vitro system is well suited for detailed, region-specific analysis of nasal spray deposition, offering a valuable tool for pharmaceutical research and development.
- Open Access
- 28 May 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 277
A coupled multilevel vial lyophilization model for the pressure coupling in a freeze dryer
- 28 May 2025
- Published by Elsevier in Applied Thermal Engineering
- Vol. 277
Open AccessA coupled multilevel vial lyophilization model for the pressure coupling in a freeze dryer
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Computational fluid dynamics challenge on indoor dispersion of pathogen-laden aerosols
This paper presents and discusses the results of the “2024 International Computational Fluid Dynamics Challenge on the long-range indoor dispersion of pathogen-laden aerosols” aimed at assessing the ability of different computational codes and turbulence models to reproduce the dispersion of particles produced by a turbulent natural convection flow enclosed in a room sized cubical cavity. A total of 12 research groups from ten different countries have conducted 15 simulations of the same flow configuration by solving the Reynolds averaged Navier–Stokes (RANS) equations, the unsteady Reynolds averaged Navier–Stokes (URANS) equations or using scale adaptive simulations (SAS), large-eddy simulations (LES), or hybrid (URANS-LES) techniques. Results for the velocity field and the particle dispersion provided by the different simulations are compared extensively, including the reference results provided by a direct numerical simulation (DNS). In general, LES and hybrid methods reproduce the time-averaged flow field correctly, the spatial distribution of the turbulence kinetic energy, and the particle dispersion. The performance of SAS is similar to that of LES and hybrid methods while the predictions of the RANS and URANS simulations exhibit larger deviations with respect to DNS. In general, the particle dispersion is better reproduced by simulations that capture correctly the spatial distribution of the turbulence kinetic energy.
- 1 February 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (2)
Computational fluid dynamics challenge on indoor dispersion of pathogen-laden aerosols
This paper presents and discusses the results of the “2024 International Computational Fluid Dynamics Challenge on the long-range indoor dispersion of pathogen-laden aerosols” aimed at assessing the ability of different computational codes and turbulence models to reproduce the dispersion of particles produced by a turbulent natural convection flow enclosed in a room sized cubical cavity. A total of 12 research groups from ten different countries have conducted 15 simulations of the same flow configuration by solving the Reynolds averaged Navier–Stokes (RANS) equations, the unsteady Reynolds averaged Navier–Stokes (URANS) equations or using scale adaptive simulations (SAS), large-eddy simulations (LES), or hybrid (URANS-LES) techniques. Results for the velocity field and the particle dispersion provided by the different simulations are compared extensively, including the reference results provided by a direct numerical simulation (DNS). In general, LES and hybrid methods reproduce the time-averaged flow field correctly, the spatial distribution of the turbulence kinetic energy, and the particle dispersion. The performance of SAS is similar to that of LES and hybrid methods while the predictions of the RANS and URANS simulations exhibit larger deviations with respect to DNS. In general, the particle dispersion is better reproduced by simulations that capture correctly the spatial distribution of the turbulence kinetic energy.
- Open Access
Development of an Experimental Dead-End Microfiltration Layout and Process Repeatability Analysis
Microfiltration is an important process in the pharmaceutical industry. Filter selection and validation is a time-consuming and expensive process. Quality by design approach is important for product safety. The article covers the instrumentalization and process control of a laboratory-scale dead-end microfiltration layout. The layout is a downscale model of the actual production line, and the goal is filter validation and analysis of process parameters, which may influence filter operation. Filter size, fluid pressure, valve plunger speed, and timing issues were considered. The focus is on the identification of the most influential process parameters and their influence on the repeatability of pressure oscillations caused by valve opening. The goal was to find the worst-case scenario regarding pressure oscillations and, consequently, filter energy intake. The layout was designed as compact as possible to reduce pressure losses between the filter and valve. Valve-induced pressure oscillations proved to be prevailing over the water hammer effect. Several filters in sizes between 3.5 cm2 and 6900 cm2 were tested, and some recommendations were suggested for the reduction of energy intake of the filter and to improve the repeatability of the process.
Open AccessDevelopment of an Experimental Dead-End Microfiltration Layout and Process Repeatability Analysis
Microfiltration is an important process in the pharmaceutical industry. Filter selection and validation is a time-consuming and expensive process. Quality by design approach is important for product safety. The article covers the instrumentalization and process control of a laboratory-scale dead-end microfiltration layout. The layout is a downscale model of the actual production line, and the goal is filter validation and analysis of process parameters, which may influence filter operation. Filter size, fluid pressure, valve plunger speed, and timing issues were considered. The focus is on the identification of the most influential process parameters and their influence on the repeatability of pressure oscillations caused by valve opening. The goal was to find the worst-case scenario regarding pressure oscillations and, consequently, filter energy intake. The layout was designed as compact as possible to reduce pressure losses between the filter and valve. Valve-induced pressure oscillations proved to be prevailing over the water hammer effect. Several filters in sizes between 3.5 cm2 and 6900 cm2 were tested, and some recommendations were suggested for the reduction of energy intake of the filter and to improve the repeatability of the process.
- Open Access
- 6 November 2023
- Published by University of Maribor in Anali PAZU
- Vol. 13 (2) , 59-70
Eksperimentalna karakterizacija spreja in numerično modeliranje razprševanja suspenzije v razpršilnem sušilniku
Drying is one of the most important and at the same time the oldest areas of process technology. One of the most established forms of drying is spray drying, which is very often present in the food, pharmaceutical and chemical industries. In this paper, we discuss the characterization of the spray formation on the spray nozzle and the implementation of numerical simulation with included secondary breakup of the spray. The characterization of the spray on the nozzle was performed on the Oxfor laser system, while the Ansys Fluent software package was used to perform the numerical simulations. A comparison of the results showed a good agreement between the particle size distribution obtained in the experiment and in the numerical simulation.
- 6 November 2023
- Published by University of Maribor in Anali PAZU
- Vol. 13 (2) , 59-70
Open AccessEksperimentalna karakterizacija spreja in numerično modeliranje razprševanja suspenzije v razpršilnem sušilniku
Drying is one of the most important and at the same time the oldest areas of process technology. One of the most established forms of drying is spray drying, which is very often present in the food, pharmaceutical and chemical industries. In this paper, we discuss the characterization of the spray formation on the spray nozzle and the implementation of numerical simulation with included secondary breakup of the spray. The characterization of the spray on the nozzle was performed on the Oxfor laser system, while the Ansys Fluent software package was used to perform the numerical simulations. A comparison of the results showed a good agreement between the particle size distribution obtained in the experiment and in the numerical simulation.
- Open Access
Energy Intake Models for Intermittent Operation of Dead-End Microfiltration Filling Line
In filling lines equipped with membrane separation devices in the form of filters energy, consumption is only one of the important working parameters, the other being sustainable filter performance in terms of separation efficiency. As the filling line is typically equipped with a valve, intermittent operation of the filter is an important form of its use. Whereas the overall energy consumption of the filtration process is governed by the continuous operation mode, the intermittent mode, characterised by opening/closing of the valve, contributes most to problems of filter failure, i.e., the breakthrough of filtered particles through the membrane. A model for determination of the energy intake of a microfiltration membrane during the opening and closing of a valve is presented in this work. The model is based on computational analysis of the pressure wave signals recorded during the opening/closing of the valve using Fourier transform, and expressed in a nondimensional filter area specific energy intake form. The model is applied to a case of constant pressure dead-end microfiltration with three filter types: a single membrane filter, a stacked filter and a pleated filter with filtration surface areas ranging from 17.7 cm2 to 2000 cm2. Both clean filters, as well as partially clogged filter cases are taken into account. Second order polynomial models of the energy intake are developed and evaluated based on extensive analysis of the experimental data. The analysis of energy intake results show that the largest energy intake was observed for the clean filter case. When membrane fouling occurs at the constant flow rate values it leads to larger energy intake, however, due to a decreasing specific flow rate during fouling these values do not exceed the clean filter case.
Open AccessEnergy Intake Models for Intermittent Operation of Dead-End Microfiltration Filling Line
In filling lines equipped with membrane separation devices in the form of filters energy, consumption is only one of the important working parameters, the other being sustainable filter performance in terms of separation efficiency. As the filling line is typically equipped with a valve, intermittent operation of the filter is an important form of its use. Whereas the overall energy consumption of the filtration process is governed by the continuous operation mode, the intermittent mode, characterised by opening/closing of the valve, contributes most to problems of filter failure, i.e., the breakthrough of filtered particles through the membrane. A model for determination of the energy intake of a microfiltration membrane during the opening and closing of a valve is presented in this work. The model is based on computational analysis of the pressure wave signals recorded during the opening/closing of the valve using Fourier transform, and expressed in a nondimensional filter area specific energy intake form. The model is applied to a case of constant pressure dead-end microfiltration with three filter types: a single membrane filter, a stacked filter and a pleated filter with filtration surface areas ranging from 17.7 cm2 to 2000 cm2. Both clean filters, as well as partially clogged filter cases are taken into account. Second order polynomial models of the energy intake are developed and evaluated based on extensive analysis of the experimental data. The analysis of energy intake results show that the largest energy intake was observed for the clean filter case. When membrane fouling occurs at the constant flow rate values it leads to larger energy intake, however, due to a decreasing specific flow rate during fouling these values do not exceed the clean filter case.
- Open Access
Experimental and Mathematical Investigation of Anaerobic Granulate Density via Settling Velocity
The objective of this study was to determine the density of anaerobic granules on different heights of a full-scale Upflow Anaerobic Sludge Bed reactor. The density was defined through the settling velocities of anaerobic granules, measured in a full-scale Upflow Anaerobic Sludge Bed reactor. In this study, granular density was calculated with the measured settling velocities and developed mathematical model. The developed mathematical model is based on the Stokes model. In the experiment, granules were taken from different heights of an Upflow Anaerobic Sludge Bed reactor, from 0.6 to 7.6 m. The granules’ diameters varied between 1 and 5 mm. The granules were taken from six different heights through the reactor. The settling velocity of the active granules (with gas in the granule pore and on the surface of the granule) was measured first. After the active granules’ settling velocity measurement, the granules were placed in a vortex to obtain degassed granules (granules without any gas in the pores or on the surface), for which the settling velocities were also measured later. It is shown that granules’ densities at different heights are independent of the reactor height.
Open AccessExperimental and Mathematical Investigation of Anaerobic Granulate Density via Settling Velocity
The objective of this study was to determine the density of anaerobic granules on different heights of a full-scale Upflow Anaerobic Sludge Bed reactor. The density was defined through the settling velocities of anaerobic granules, measured in a full-scale Upflow Anaerobic Sludge Bed reactor. In this study, granular density was calculated with the measured settling velocities and developed mathematical model. The developed mathematical model is based on the Stokes model. In the experiment, granules were taken from different heights of an Upflow Anaerobic Sludge Bed reactor, from 0.6 to 7.6 m. The granules’ diameters varied between 1 and 5 mm. The granules were taken from six different heights through the reactor. The settling velocity of the active granules (with gas in the granule pore and on the surface of the granule) was measured first. After the active granules’ settling velocity measurement, the granules were placed in a vortex to obtain degassed granules (granules without any gas in the pores or on the surface), for which the settling velocities were also measured later. It is shown that granules’ densities at different heights are independent of the reactor height.
- Open Access
- 7 September 2022
- Published by Springer Nature in Theoretical and Computational Fluid Dynamics
- Vol. 36 (5) , 723-740
A specific slip length model for the Maxwell slip boundary conditions in the Navier–Stokes solution of flow around a microparticle in the no-slip and slip flow regimes
In the case of microscopic particles, the momentum exchange between the particle and the gas flow starts to deviate from the standard macroscopic particle case, i.e. the no-slip case, with slip flow occurring in the case of low to moderate particle Knudsen numbers. In order to derive new drag force models that are valid also in the slip flow regime for the case of non-spherical particles of arbitrary shapes using computational fluid dynamics, the no-slip conditions at the particle surface have to be modified in order to account for the velocity slip at the surface, mostly in the form of the Maxwell’s slip model. To allow a continuous transition in the boundary condition at the wall from the no-slip case to the slip cases for various Knudsen (Kn) number value flow regimes, a novel specific slip length model for the use with the Maxwell boundary conditions is proposed. The model is derived based on the data from the published experimental studies on spherical microparticle drag force correlations and Cunningham-based slip correction factors at standard conditions and uses a detailed CFD study on microparticle fluid dynamics to determine the correct values of the specific slip length at selected Kn number conditions. The obtained data on specific slip length are correlated using a polynomial function, resulting in the specific slip length model for the no-slip and slip flow regimes that can be applied to arbitrary convex particle shapes. Graphic
- 7 September 2022
- Published by Springer Nature in Theoretical and Computational Fluid Dynamics
- Vol. 36 (5) , 723-740
Open AccessA specific slip length model for the Maxwell slip boundary conditions in the Navier–Stokes solution of flow around a microparticle in the no-slip and slip flow regimes
In the case of microscopic particles, the momentum exchange between the particle and the gas flow starts to deviate from the standard macroscopic particle case, i.e. the no-slip case, with slip flow occurring in the case of low to moderate particle Knudsen numbers. In order to derive new drag force models that are valid also in the slip flow regime for the case of non-spherical particles of arbitrary shapes using computational fluid dynamics, the no-slip conditions at the particle surface have to be modified in order to account for the velocity slip at the surface, mostly in the form of the Maxwell’s slip model. To allow a continuous transition in the boundary condition at the wall from the no-slip case to the slip cases for various Knudsen (Kn) number value flow regimes, a novel specific slip length model for the use with the Maxwell boundary conditions is proposed. The model is derived based on the data from the published experimental studies on spherical microparticle drag force correlations and Cunningham-based slip correction factors at standard conditions and uses a detailed CFD study on microparticle fluid dynamics to determine the correct values of the specific slip length at selected Kn number conditions. The obtained data on specific slip length are correlated using a polynomial function, resulting in the specific slip length model for the no-slip and slip flow regimes that can be applied to arbitrary convex particle shapes. Graphic