Serdar Tez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Serdar Tez has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Mehmet Kaya
Department of Electrical and Electronics Engineering, Graduate School of Natural and Applied Sciences, Pamukkale University, Denizli, Turkey
3 shared publications Tayfun Akin
METU MEMS Res. and App. Center, Dept. of Elect. and Electr. Engin., Middle East Technical University, Ankara, Turkey
3 shared publicationsMustafa Mert Torunbalci
METU MEMS Res. and App. Center, Middle East Technical University, Ankara, Turkey
2 shared publications- A. M. Babayev
Faculty of Arts and Sciences, Süleyman Demirel University
1 shared publication A.M. Babayev
Azerbaijan National Academy of Sciences
1 shared publicationErgun Aytaşkın
1 shared publication
Latest Publications
- 12 July 2023
- Published by Springer Nature in Microsystem Technologies
- Vol. 29 (9) , 1281-1293
A simulation study verified by experimental test results for frequency response analysis of MEMS comb-drive resonator
- 12 July 2023
- Published by Springer Nature in Microsystem Technologies
- Vol. 29 (9) , 1281-1293
A simulation study verified by experimental test results for frequency response analysis of MEMS comb-drive resonator
- 6 February 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (7) , 3078-3093
Integration of conducting polymers with MEMS lateral comb-drive resonator via electrodeposition for VOCs detection
- 6 February 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (7) , 3078-3093
Integration of conducting polymers with MEMS lateral comb-drive resonator via electrodeposition for VOCs detection
- 19 March 2021
- Published by Springer Nature in Journal of Computational Electronics
- Vol. 20 (2) , 1020-1031
Development of algorithms in open-source Elmer FEM for frequency response and biased modal analysis of MEMS cantilever
- 19 March 2021
- Published by Springer Nature in Journal of Computational Electronics
- Vol. 20 (2) , 1020-1031
Development of algorithms in open-source Elmer FEM for frequency response and biased modal analysis of MEMS cantilever
- 4 March 2021
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 63 (7) , 1813-1819
Photonic crystal bandpass filter exploiting the degenerate modes tunable with MEMS actuator for terahertz application
- 4 March 2021
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 63 (7) , 1813-1819
Photonic crystal bandpass filter exploiting the degenerate modes tunable with MEMS actuator for terahertz application
- 10 February 2020
- Published by AVES YAYINCILIK A.Ş. in Electrica
- Vol. 20 (1) , 41-51
Design of a MEMS-Based Capacitive Resonator for Target Analyte Detection
The present study introduces a microelectromechanical systems (MEMS) capacitive comb-finger resonator designed for the detection of different target analytes by using the detection mechanism based on the resonance frequency shift. This kind of applications is generally needed for a sensing layer capable of absorbing the desired target species in a molecular level, resulting in a change in the mass of the resonator. Therefore, a conceptual fabrication model is also described to form such a layer on the sensor. The dimension of the designed resonator structure is nearly 1766 µm×1998 µm, and the structural thickness of the sensor is planned to be 35 µm thick. Moreover, the design values of rest capacitance and resonance frequency of the structure are nearly 1 pF and 49 kHz, respectively. The inverse of the mass responsivity of the design given in the study is calculated as 370 pg/Hz. In addition to theoretical calculations, the mechanical and electrical simulations are also performed to verify the results. Cite this article as: Tez S, Aytaşkın E. Design of a MEMS-Based Capacitive Resonator for Target Analyte Detection. Electrica, 2020; 20(1): 41-51.
- 10 February 2020
- Published by AVES YAYINCILIK A.Ş. in Electrica
- Vol. 20 (1) , 41-51
Design of a MEMS-Based Capacitive Resonator for Target Analyte Detection
The present study introduces a microelectromechanical systems (MEMS) capacitive comb-finger resonator designed for the detection of different target analytes by using the detection mechanism based on the resonance frequency shift. This kind of applications is generally needed for a sensing layer capable of absorbing the desired target species in a molecular level, resulting in a change in the mass of the resonator. Therefore, a conceptual fabrication model is also described to form such a layer on the sensor. The dimension of the designed resonator structure is nearly 1766 µm×1998 µm, and the structural thickness of the sensor is planned to be 35 µm thick. Moreover, the design values of rest capacitance and resonance frequency of the structure are nearly 1 pF and 49 kHz, respectively. The inverse of the mass responsivity of the design given in the study is calculated as 370 pg/Hz. In addition to theoretical calculations, the mechanical and electrical simulations are also performed to verify the results. Cite this article as: Tez S, Aytaşkın E. Design of a MEMS-Based Capacitive Resonator for Target Analyte Detection. Electrica, 2020; 20(1): 41-51.
- 1 March 2018
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 86, 202-209
A novel voltage-mode universal filter composed of two terminal active devices
- 1 March 2018
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 86, 202-209
A novel voltage-mode universal filter composed of two terminal active devices
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
A novel method for fabricating MEMS three-axis accelerometers using low temperature Au-Sn eutectic bonding
This paper presents a novel method for the fabrication of three-axis capacitive MEMS accelerometers by using low-temperature Au-Sn eutectic bonding that is applied to form a glass-silicon-glass multi-stack. The proposed method provides the implementation of individual in-plane and out-of-plane accelerometer elements in the same die using a glass-silicon-glass multi-stack structure formed at temperatures as low as 300°C while still ensuring the advantages of the previous approaches such as the voltage free bonding, inherent capping, and the differential sensing. The initial prototypes are verified to be functional and mechanically strong (>9.5MPa) by C-V measurements and shear strength tests.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-3
A novel method for fabricating MEMS three-axis accelerometers using low temperature Au-Sn eutectic bonding
This paper presents a novel method for the fabrication of three-axis capacitive MEMS accelerometers by using low-temperature Au-Sn eutectic bonding that is applied to form a glass-silicon-glass multi-stack. The proposed method provides the implementation of individual in-plane and out-of-plane accelerometer elements in the same die using a glass-silicon-glass multi-stack structure formed at temperatures as low as 300°C while still ensuring the advantages of the previous approaches such as the voltage free bonding, inherent capping, and the differential sensing. The initial prototypes are verified to be functional and mechanically strong (>9.5MPa) by C-V measurements and shear strength tests.
- 7 August 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 24 (5) , 1264-1274
A Bulk-Micromachined Three-Axis Capacitive MEMS Accelerometer on a Single Die
This paper presents a high-performance three-axis capacitive microelectromechanical system (MEMS) accelerometer implemented by fabricating individual lateral and vertical differential accelerometers in the same die. The fabrication process is based on the formation of a glass-silicon-glass multi-stack. First, a 35-μm (111) silicon structural layer of an Silicon-On-Insulator (SOI) wafer is patterned with deep reactive ion etching (DRIE) and attached on a base glass substrate with anodic bonding, whose handle layer is later removed. Next, the second glass wafer is placed on the top of the structure not only for allowing to implement a top electrode for the vertical accelerometer, but also for acting as an inherent cap for the entire structure. The fabricated three-axis MEMS capacitive accelerometer die measures 12 × 7 × 1 mm 3 . The x-axis and y-axis accelerometers demonstrate measured noise floors and bias instabilities equal to or better than 5.5 μg/√Hz and 2.2 μg, respectively, while the z-axis accelerometer demonstrates 12.6 μg/√Hz noise floor and 17.4 μg bias instability values using hybrid-connected fourth-order sigma-delta CMOS application specific integrated circuit (ASIC) chips. These low noise performances are achieved with a measurement range of over ±10 g for the x-axis and y-axis accelerometers and +12/-7.5 g for the z-axis accelerometer, suggesting their potential use in navigation grade applications.
- 7 August 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Microelectromechanical Systems
- Vol. 24 (5) , 1264-1274
A Bulk-Micromachined Three-Axis Capacitive MEMS Accelerometer on a Single Die
This paper presents a high-performance three-axis capacitive microelectromechanical system (MEMS) accelerometer implemented by fabricating individual lateral and vertical differential accelerometers in the same die. The fabrication process is based on the formation of a glass-silicon-glass multi-stack. First, a 35-μm (111) silicon structural layer of an Silicon-On-Insulator (SOI) wafer is patterned with deep reactive ion etching (DRIE) and attached on a base glass substrate with anodic bonding, whose handle layer is later removed. Next, the second glass wafer is placed on the top of the structure not only for allowing to implement a top electrode for the vertical accelerometer, but also for acting as an inherent cap for the entire structure. The fabricated three-axis MEMS capacitive accelerometer die measures 12 × 7 × 1 mm 3 . The x-axis and y-axis accelerometers demonstrate measured noise floors and bias instabilities equal to or better than 5.5 μg/√Hz and 2.2 μg, respectively, while the z-axis accelerometer demonstrates 12.6 μg/√Hz noise floor and 17.4 μg bias instability values using hybrid-connected fourth-order sigma-delta CMOS application specific integrated circuit (ASIC) chips. These low noise performances are achieved with a measurement range of over ±10 g for the x-axis and y-axis accelerometers and +12/-7.5 g for the z-axis accelerometer, suggesting their potential use in navigation grade applications.
- 1 November 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 41 42 (19300395) , 1-4
Fabrication of a sandwich type three axis capacitive MEMS accelerometer
This paper presents a three axis capacitive MEMS accelerometer including individual lateral and vertical accelerometers in a same die. The three axis capacitive MEMS accelerometer is fabricated by utilizing a glass-silicon-glass multi-stack formed by a fabrication process depending on the double glass modified silicon on glass process (DGM-SOG), where the structural layer is selected to be 35 μm thick <;111> silicon. The fabrication process uses the Au-Si eutectic bonding in the last step of the formation of the glass-silicon-glass multi-stack, eliminating the stiction risk of the suspended silicon structures to the top glass with the voltage free feature of the Au-Si eutectic bonding method, allowing to implement 2 μm capacitive gaps for the vertical accelerometers without any pull in during fabrication, while matching 2μιη capacitive gaps of the lateral accelerometers. The top glass wafer allows implementing not only a top electrode for the vertical accelerometer, but also a cap for the entire structure. The fabricated three axis MEMS capacitive accelerometer die is 12×7×1 mm 3 . Measured capacitances of the lateral and the vertical accelerometers are 9.4 pF and 7.4 pF, but their capacitance change is similar to each other, as they are approximately measured as 90 fF/V and 100 fF/V, respectively. The Brownian noise of the lateral and vertical are estimated to be 6 Mg/√Hz and 7.6 Mg/√Hz, respectively.
- 1 November 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 41 42 (19300395) , 1-4
Fabrication of a sandwich type three axis capacitive MEMS accelerometer
This paper presents a three axis capacitive MEMS accelerometer including individual lateral and vertical accelerometers in a same die. The three axis capacitive MEMS accelerometer is fabricated by utilizing a glass-silicon-glass multi-stack formed by a fabrication process depending on the double glass modified silicon on glass process (DGM-SOG), where the structural layer is selected to be 35 μm thick <;111> silicon. The fabrication process uses the Au-Si eutectic bonding in the last step of the formation of the glass-silicon-glass multi-stack, eliminating the stiction risk of the suspended silicon structures to the top glass with the voltage free feature of the Au-Si eutectic bonding method, allowing to implement 2 μm capacitive gaps for the vertical accelerometers without any pull in during fabrication, while matching 2μιη capacitive gaps of the lateral accelerometers. The top glass wafer allows implementing not only a top electrode for the vertical accelerometer, but also a cap for the entire structure. The fabricated three axis MEMS capacitive accelerometer die is 12×7×1 mm 3 . Measured capacitances of the lateral and the vertical accelerometers are 9.4 pF and 7.4 pF, but their capacitance change is similar to each other, as they are approximately measured as 90 fF/V and 100 fF/V, respectively. The Brownian noise of the lateral and vertical are estimated to be 6 Mg/√Hz and 7.6 Mg/√Hz, respectively.
- Open Access
- 1 January 2012
- Published by Elsevier in Procedia Engineering
- Vol. 47, 342-345
Comparison of Two Alternative Fabrication Processes for a Three-Axis Capacitive MEMS Accelerometer
- 1 January 2012
- Published by Elsevier in Procedia Engineering
- Vol. 47, 342-345
Open AccessComparison of Two Alternative Fabrication Processes for a Three-Axis Capacitive MEMS Accelerometer