Jelena Šantek Bajto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jelena Šantek Bajto has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Nina Štirmer
University of Zagreb
3 shared publications - Ana Baričević
Department of Materials, Faculty of Civil Engineering, University of Zagreb, Fra Andrije Kačića Miošića 26, 10000 Zagreb, Croatia
2 shared publications - Ivana Carević
University of Zagreb
2 shared publications Nina Štirmer
Department of Materials, University of Zagreb, Faculty of Civil Engineering, Zagreb, Croatia
2 shared publicationsAna Baričević
University of Zagreb
1 shared publicationIvana Carević
Department of Materials, University of Zagreb, Faculty of Civil Engineering, Zagreb, Croatia
1 shared publication
Latest Publications
- Open Access
- 19 January 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Wood biomass ash as a clinker substitute in advancing next-generation blended cement: Croatian case study
This research investigates the use of wood biomass ash (WBA) as a supplementary cementitious material (SCM) in blended cement formulations containing 6 and 12 wt% of bottom WBA. Motivated by the need to advance low-carbon cement production, reduce reliance on imported materials, and incorporate waste management strategies, the study explores sustainable pathways for cement manufacturing. Experimental results show that the 6 wt% WBA blend (BLEND BC-II) achieves a compressive strength of 59.3 MPa after 28 days, surpassing the reference CEM II, whereas the 12 wt% WBA blend (BLEND BC-I) also delivers favourable mechanical and durability performance, including a chloride diffusion coefficient of 15.85 × 10⁻¹² m²/s, capillary absorption of 0.68 g/m²·h¹/², and gas permeability of 0.50 × 10⁻¹⁶ m². Volume stability tests of the 12 wt% WBA blend confirm that autogenous deformations remain below − 0.017 mm/m after 90 days, indicating effective mitigation of shrinkage and reliable dimensional stability. When combined with other SCMs, WBA further improves long-term mechanical performance. Despite challenges related to compositional variability and infrastructure requirements, WBA incorporation can reduce environmental impact and support low-carbon cement production. Achieving net-zero emissions extends beyond quantitative targets, requiring the restoration of balance between resource use, material efficiency, and environmental sustainability. These findings demonstrate that WBA is a viable SCM, advancing sustainable and resilient cement manufacturing.
- 19 January 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1)
Open AccessWood biomass ash as a clinker substitute in advancing next-generation blended cement: Croatian case study
This research investigates the use of wood biomass ash (WBA) as a supplementary cementitious material (SCM) in blended cement formulations containing 6 and 12 wt% of bottom WBA. Motivated by the need to advance low-carbon cement production, reduce reliance on imported materials, and incorporate waste management strategies, the study explores sustainable pathways for cement manufacturing. Experimental results show that the 6 wt% WBA blend (BLEND BC-II) achieves a compressive strength of 59.3 MPa after 28 days, surpassing the reference CEM II, whereas the 12 wt% WBA blend (BLEND BC-I) also delivers favourable mechanical and durability performance, including a chloride diffusion coefficient of 15.85 × 10⁻¹² m²/s, capillary absorption of 0.68 g/m²·h¹/², and gas permeability of 0.50 × 10⁻¹⁶ m². Volume stability tests of the 12 wt% WBA blend confirm that autogenous deformations remain below − 0.017 mm/m after 90 days, indicating effective mitigation of shrinkage and reliable dimensional stability. When combined with other SCMs, WBA further improves long-term mechanical performance. Despite challenges related to compositional variability and infrastructure requirements, WBA incorporation can reduce environmental impact and support low-carbon cement production. Achieving net-zero emissions extends beyond quantitative targets, requiring the restoration of balance between resource use, material efficiency, and environmental sustainability. These findings demonstrate that WBA is a viable SCM, advancing sustainable and resilient cement manufacturing.
- Open Access
Sustainable Hybrid Lime Mortars for Historic Building Conservation: Incorporating Wood Biomass Ash as a Low-Carbon Secondary Binder
Renewables-based power grid expansion has increased the use of wood biomass as a low-carbon fuel, resulting in the generation of predominantly inorganic wood biomass ash (WBA) as waste during biomass combustion. The conservation of historically valuable, damaged, and energy-inefficient buildings can help downsize carbon emissions and energy consumption, while promoting the use of alternative repair materials, including unavailing materials such as WBA, and implementing zero-waste measures. This study aims to underscore the importance of a proactive approach in managing WBA and its application in artificial hydraulic lime (AHL) mortars. Hybrid lime mortars were prepared by combining natural hydraulic lime (NHL) as the primary binder with fly wood biomass ash (WBA) as the secondary substitute, using different mass ratios of NHL to WBA (100:0, 80:20, and 70:30). The experimental framework encompassed interconnected analytical steps, ranging from binder analysis to paste and mortar preparation. The chemical and mineralogical composition, physical properties, and reactivity of WBA were evaluated to determine the appropriate proportion of WBA for low-carbon AHL binder formulation. Prior to mortar mixing, the water demand, setting time, and soundness of the AHL pastes were assessed. The effects of each AHL binder blend on the mechanical properties of the AHL mortars were analyzed based on compressive and flexural strength measurements after 28 days of curing under different CO2 and moisture conditions (CO2~400 ppm at 70% RH and 95% RH; CO2~30,000 ppm at 60% RH). Additionally, changes in the porous structure were studied. Notwithstanding the greatly prolonged setting time, the results indicate that the mechanical properties of AHL mortars can be enhanced by the addition of WBA in a moderate ratio, empowering the development of environmentally friendly lime mortars suitable for conservation purposes.
Open AccessSustainable Hybrid Lime Mortars for Historic Building Conservation: Incorporating Wood Biomass Ash as a Low-Carbon Secondary Binder
Renewables-based power grid expansion has increased the use of wood biomass as a low-carbon fuel, resulting in the generation of predominantly inorganic wood biomass ash (WBA) as waste during biomass combustion. The conservation of historically valuable, damaged, and energy-inefficient buildings can help downsize carbon emissions and energy consumption, while promoting the use of alternative repair materials, including unavailing materials such as WBA, and implementing zero-waste measures. This study aims to underscore the importance of a proactive approach in managing WBA and its application in artificial hydraulic lime (AHL) mortars. Hybrid lime mortars were prepared by combining natural hydraulic lime (NHL) as the primary binder with fly wood biomass ash (WBA) as the secondary substitute, using different mass ratios of NHL to WBA (100:0, 80:20, and 70:30). The experimental framework encompassed interconnected analytical steps, ranging from binder analysis to paste and mortar preparation. The chemical and mineralogical composition, physical properties, and reactivity of WBA were evaluated to determine the appropriate proportion of WBA for low-carbon AHL binder formulation. Prior to mortar mixing, the water demand, setting time, and soundness of the AHL pastes were assessed. The effects of each AHL binder blend on the mechanical properties of the AHL mortars were analyzed based on compressive and flexural strength measurements after 28 days of curing under different CO2 and moisture conditions (CO2~400 ppm at 70% RH and 95% RH; CO2~30,000 ppm at 60% RH). Additionally, changes in the porous structure were studied. Notwithstanding the greatly prolonged setting time, the results indicate that the mechanical properties of AHL mortars can be enhanced by the addition of WBA in a moderate ratio, empowering the development of environmentally friendly lime mortars suitable for conservation purposes.
- 8 June 2023
- Published by Springer Nature
- p. 359-373
Restoring Historical Buildings Amid Climate Crisis: Hydraulic, Waste-Based Lime
- 8 June 2023
- Published by Springer Nature
- p. 359-373
Restoring Historical Buildings Amid Climate Crisis: Hydraulic, Waste-Based Lime
- Open Access
Pilot Scale Production of Precast Concrete Elements with Wood Biomass Ash
Downsizing fossil fuel dependence and greenhouse gas emissions is at the forefront of a sustainable future. The expansion of renewable energy while striving to minimize dependence on fossil fuels has led to biomass taking the lead among renewable energy sources, with wood having the broadest application. Along with the growing trend of using biomass as a renewable energy source, the combustion of wood biomass results in wood biomass ash (WBA), leading to compelling amounts of waste. In this study, the technical feasibility of fly WBA from different Croatian power plants was analyzed to evaluate its potential use in precast concrete drainage elements and curb units. By implementing a performance-based design, the influence of various factors in thermal processing of wood biomass was investigated, together with a detailed characterization of WBA in order to assess the feasibility of using WBA as a secondary raw material in a large-scale industrial batching plant. The compressive strength and durability properties (water absorption, permeability, and freeze–thaw resistance) of concrete mixtures with WBA as a replacement for 15 wt% cement were evaluated and compared with the precast concrete manufacturer’s technical requirements. The main concerns identified were compositional inconsistency of WBA, workability downturn, delay in initial reactivity rate, and increased water absorption. Concrete with WBA based on a circular design has been found to be a viable solution to cement depletion, stepping up from recycling to reuse of industrial waste.
Open AccessPilot Scale Production of Precast Concrete Elements with Wood Biomass Ash
Downsizing fossil fuel dependence and greenhouse gas emissions is at the forefront of a sustainable future. The expansion of renewable energy while striving to minimize dependence on fossil fuels has led to biomass taking the lead among renewable energy sources, with wood having the broadest application. Along with the growing trend of using biomass as a renewable energy source, the combustion of wood biomass results in wood biomass ash (WBA), leading to compelling amounts of waste. In this study, the technical feasibility of fly WBA from different Croatian power plants was analyzed to evaluate its potential use in precast concrete drainage elements and curb units. By implementing a performance-based design, the influence of various factors in thermal processing of wood biomass was investigated, together with a detailed characterization of WBA in order to assess the feasibility of using WBA as a secondary raw material in a large-scale industrial batching plant. The compressive strength and durability properties (water absorption, permeability, and freeze–thaw resistance) of concrete mixtures with WBA as a replacement for 15 wt% cement were evaluated and compared with the precast concrete manufacturer’s technical requirements. The main concerns identified were compositional inconsistency of WBA, workability downturn, delay in initial reactivity rate, and increased water absorption. Concrete with WBA based on a circular design has been found to be a viable solution to cement depletion, stepping up from recycling to reuse of industrial waste.
- Open Access
Potential of Using Wood Biomass Ash in Low-Strength Composites
Reducing greenhouse gas emissions and dependence on fossil fuels is the cornerstone of all European climate and energy strategies. Consequently, renewable energy sources are becoming more competitive with fossil fuels. The largest source of bioenergy in the European Union is biomass-fired power plants. Therefore, the European coal phase-out strategy led to an increased use of wood biomass as a sustainable fuel, generating large amounts of wood biomass ash (WBA). In the research studies reported so far, WBA has been mainly used in cementitious composites. However, given the similarities between the chemical composition of WBA and hydraulic lime (HL), this research focused on its potential classification as a building lime. Overall, three different sources of fly WBA were considered for the preparation of binders as mixtures of WBA and coal fly ash (CFA) in different ratios. The contribution of each binder mixture on the paste and mortar properties was analyzed based on the chemical composition, setting time, volume stability, and contribution to the mortar strength (compressive and flexural). In general, it can be concluded that the studied binders can meet the criteria of EN 459-1. However, special attention should be paid to the volume deformations and the setting time.
Open AccessPotential of Using Wood Biomass Ash in Low-Strength Composites
Reducing greenhouse gas emissions and dependence on fossil fuels is the cornerstone of all European climate and energy strategies. Consequently, renewable energy sources are becoming more competitive with fossil fuels. The largest source of bioenergy in the European Union is biomass-fired power plants. Therefore, the European coal phase-out strategy led to an increased use of wood biomass as a sustainable fuel, generating large amounts of wood biomass ash (WBA). In the research studies reported so far, WBA has been mainly used in cementitious composites. However, given the similarities between the chemical composition of WBA and hydraulic lime (HL), this research focused on its potential classification as a building lime. Overall, three different sources of fly WBA were considered for the preparation of binders as mixtures of WBA and coal fly ash (CFA) in different ratios. The contribution of each binder mixture on the paste and mortar properties was analyzed based on the chemical composition, setting time, volume stability, and contribution to the mortar strength (compressive and flexural). In general, it can be concluded that the studied binders can meet the criteria of EN 459-1. However, special attention should be paid to the volume deformations and the setting time.