Paul Hiret
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Paul Hiret has a total of 71 co-authors. Here are the top co-authors by number of shared publications:
- Laurent Marot
University of Basel
10 shared publications - Ernst Meyer
Department of Physics University of Basel Basel Switzerland
6 shared publications - Jérôme Moritz
Université de Lorraine, CNRS, IJL 2 , F-54000 Nancy
6 shared publications - Artem M. Dmitriev
Department of Physics, University of Basel, Klingelbergstrasse 82, CH-4056 Basel, Switzerland
5 shared publications - Frédéric Brochard
Institut Jean Lamour, Université de Lorraine, CNRS
5 shared publications - Stephane Heuraux
Institut Jean Lamour UMR 7198 CNRS-Université de Lorraine, BP 50840, F-5401 Nancy, France
4 shared publications
Latest Publications
- 17 November 2026
- Published by IOP Publishing in Plasma Sources Science and Technology
Scaling of RF sheath rectification in magnetized plasmas: Electron phase-induced enhancement and collapse
This paper investigates radio-frequency (RF) sheath rectification in strongly magnetized discharges under inclined magnetic field configurations using 1D3V Particle-In-Cell (PIC) simulations and an analytical Plasma Series Resonance (PSR) model. We show that tilting the magnetic field toward grazing incidence (θ → 0) lowers the resonant frequency of the plasma-sheath system by effectively increasing the electron inertia along field lines. The dynamic response of the system is universally governed by the dimensionless parameter χ = ωpe sin θ /ω, which controls the interplay between the projected plasma frequency and the RF driving frequency ω. For large values (χ ≫ 100), the normalized rectified potential (VDC − Vfl )/VRF follows the classical capacitive limit of 1/π. As χ decreases,ion inertia effects cause the normalized potential to asymptote toward 1/2. At in- termediate values (χr ≈ 3–5), a strong resonant enhancement of VDC occurs, driven by the series resonance between the capacitive sheath and the inductive magnetized bulk. This potential peak is strongly attenuated as electron–neutral collisionality increases. Finally, for grazing angles near χ ≃ 1, the electron transit time through the sheath matches the RF period leading to a total collapse of the rectified potential. The analytical PSR model shows excellent agreement with PIC simulations across a wide of driving frequencies, RF voltage amplitudes, and discharge lengths. These results provide a robust predictive framework for controlling sheath potentials, impurity sourcing, and power coupling in industrial plasma sources and ion cyclotron resonance heating (ICRH) antennas in fusion devices.
- 17 November 2026
- Published by IOP Publishing in Plasma Sources Science and Technology
Scaling of RF sheath rectification in magnetized plasmas: Electron phase-induced enhancement and collapse
This paper investigates radio-frequency (RF) sheath rectification in strongly magnetized discharges under inclined magnetic field configurations using 1D3V Particle-In-Cell (PIC) simulations and an analytical Plasma Series Resonance (PSR) model. We show that tilting the magnetic field toward grazing incidence (θ → 0) lowers the resonant frequency of the plasma-sheath system by effectively increasing the electron inertia along field lines. The dynamic response of the system is universally governed by the dimensionless parameter χ = ωpe sin θ /ω, which controls the interplay between the projected plasma frequency and the RF driving frequency ω. For large values (χ ≫ 100), the normalized rectified potential (VDC − Vfl )/VRF follows the classical capacitive limit of 1/π. As χ decreases,ion inertia effects cause the normalized potential to asymptote toward 1/2. At in- termediate values (χr ≈ 3–5), a strong resonant enhancement of VDC occurs, driven by the series resonance between the capacitive sheath and the inductive magnetized bulk. This potential peak is strongly attenuated as electron–neutral collisionality increases. Finally, for grazing angles near χ ≃ 1, the electron transit time through the sheath matches the RF period leading to a total collapse of the rectified potential. The analytical PSR model shows excellent agreement with PIC simulations across a wide of driving frequencies, RF voltage amplitudes, and discharge lengths. These results provide a robust predictive framework for controlling sheath potentials, impurity sourcing, and power coupling in industrial plasma sources and ion cyclotron resonance heating (ICRH) antennas in fusion devices.
- Open Access
- 30 September 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (12) , 126031
Mirror cleaning of the ITER Core Plasma Thomson Scattering system using 13.56–80 MHz discharges
The first mirror unit (FMU) is a critical front-end component of the collection optics in the ITER Core Plasma Thomson Scattering (CPTS) diagnostic, responsible for monitoring electron density and temperature. Large-sized metallic first (M1) and second (M2) mirrors are integrated into the CPTS FMU to collect and reflect optical signals from the fusion plasma to downstream optics. Due to its proximity to the plasma, M1 requires periodic in-situ cleaning to prevent severe optical degradation caused primarily by deposition. A simplified full-scale 1:1 mock-up of the FMU was manufactured to experimentally assess the radio-frequency (RF) plasma parameters over a wide frequency range of 13.56–80 MHz using a retarding field energy analyzer. With increasing pressure and frequency, the magnitude of the direct current (DC) self-bias, mean ion energy, and energy splitting decreased, while the ion flux increased. In addition, particular attention was given to the DC grounding effect by introducing quarter-wavelength shorted stubs as notch filters (NFs). In this preliminary RF circuit design, one or both mirrors could be RF-powered, with the remaining surfaces acting as grounded electrodes. Based on the selected parameters, M1 cleaning experiments with DC grounding or self-bias were conducted, followed by elemental composition and reflectivity analysis via x-ray photoelectron spectroscopy and spectrophotometry. The complete removal of 20 nm alumina on M1 was achieved at 13.56 MHz for both configurations, and substantial heating of RF components and the chamber was observed at all frequencies. Moreover, compared with the self-bias case, structural material could be deposited on both mirrors after cleaning with NF, owing to enhanced wall sputtering and weaker mirror cleaning. The feasibility of powering both mirrors simultaneously with self-bias was also demonstrated. Finally, significant power reflection from the load was confirmed using an Octiv voltage–current probe, highlighting the need for improved power transfer in the CPTS mirror cleaning system.
- 30 September 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (12) , 126031
Open AccessMirror cleaning of the ITER Core Plasma Thomson Scattering system using 13.56–80 MHz discharges
The first mirror unit (FMU) is a critical front-end component of the collection optics in the ITER Core Plasma Thomson Scattering (CPTS) diagnostic, responsible for monitoring electron density and temperature. Large-sized metallic first (M1) and second (M2) mirrors are integrated into the CPTS FMU to collect and reflect optical signals from the fusion plasma to downstream optics. Due to its proximity to the plasma, M1 requires periodic in-situ cleaning to prevent severe optical degradation caused primarily by deposition. A simplified full-scale 1:1 mock-up of the FMU was manufactured to experimentally assess the radio-frequency (RF) plasma parameters over a wide frequency range of 13.56–80 MHz using a retarding field energy analyzer. With increasing pressure and frequency, the magnitude of the direct current (DC) self-bias, mean ion energy, and energy splitting decreased, while the ion flux increased. In addition, particular attention was given to the DC grounding effect by introducing quarter-wavelength shorted stubs as notch filters (NFs). In this preliminary RF circuit design, one or both mirrors could be RF-powered, with the remaining surfaces acting as grounded electrodes. Based on the selected parameters, M1 cleaning experiments with DC grounding or self-bias were conducted, followed by elemental composition and reflectivity analysis via x-ray photoelectron spectroscopy and spectrophotometry. The complete removal of 20 nm alumina on M1 was achieved at 13.56 MHz for both configurations, and substantial heating of RF components and the chamber was observed at all frequencies. Moreover, compared with the self-bias case, structural material could be deposited on both mirrors after cleaning with NF, owing to enhanced wall sputtering and weaker mirror cleaning. The feasibility of powering both mirrors simultaneously with self-bias was also demonstrated. Finally, significant power reflection from the load was confirmed using an Octiv voltage–current probe, highlighting the need for improved power transfer in the CPTS mirror cleaning system.
- Open Access
- 21 January 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (2) , 026042
Influence of 3 T magnetic field on RF plasma self-bias and erosion pattern for the ITER wide angle viewing system
The ITER Wide Angle Viewing System (WAVS) relies on in-vessel metallic first mirrors (FM) to transport optical signals from the plasma to out-of-vessel diagnostics. Under the conditions of ITER, energetic plasma particles induce sputtering of plasma-facing components, and the resulting sputtered material can re-deposit on these mirrors, resulting in reflectivity degradation. In-situ plasma removal using radio-frequency (RF) capacitively coupled plasma discharges is one of the proposed methods to mitigate this issue. Experiments were conducted in a 3 T homogeneous magnetic field using a medical magnetic resonance imaging (MRI) system at the University Hospital of Basel. The WAVS First Mirror Unit consists of two mirror electrodes (M1 and M2), one or both of which can be powered with RF, while the remaining surfaces act as grounded areas. Systematic measurements of the self-bias voltage were performed for varying discharge conditions, including gas species (argon and helium), pressure (0.1–10 Pa) and mirror capacitance, as well as the angle θ between the mirror surface and magnetic field. The results revealed a strong dependence of the self-bias on the grounded-to-powered area ratio A g / A p , which is affected by the magnetic confinement. Erosion and deposition patterns were examined in cases where one or both mirrors were powered. Erosion occurred primarily where a powered mirror faces a grounded surface, whereas overlapping discharges in the dual-powered case resulted in low ion kinetic energy and preferential net deposition at the overlapping area. These observations were supported by one-dimensional simulations of plasma potential evolution under representative conditions. These results provide critical insight into RF plasma behaviour in fully magnetised, geometrically asymmetric discharges and support the development of robust in-situ cleaning strategies for ITER optical diagnostics.
- 21 January 2026
- Published by IOP Publishing in Nuclear Fusion
- Vol. 66 (2) , 026042
Open AccessInfluence of 3 T magnetic field on RF plasma self-bias and erosion pattern for the ITER wide angle viewing system
The ITER Wide Angle Viewing System (WAVS) relies on in-vessel metallic first mirrors (FM) to transport optical signals from the plasma to out-of-vessel diagnostics. Under the conditions of ITER, energetic plasma particles induce sputtering of plasma-facing components, and the resulting sputtered material can re-deposit on these mirrors, resulting in reflectivity degradation. In-situ plasma removal using radio-frequency (RF) capacitively coupled plasma discharges is one of the proposed methods to mitigate this issue. Experiments were conducted in a 3 T homogeneous magnetic field using a medical magnetic resonance imaging (MRI) system at the University Hospital of Basel. The WAVS First Mirror Unit consists of two mirror electrodes (M1 and M2), one or both of which can be powered with RF, while the remaining surfaces act as grounded areas. Systematic measurements of the self-bias voltage were performed for varying discharge conditions, including gas species (argon and helium), pressure (0.1–10 Pa) and mirror capacitance, as well as the angle θ between the mirror surface and magnetic field. The results revealed a strong dependence of the self-bias on the grounded-to-powered area ratio A g / A p , which is affected by the magnetic confinement. Erosion and deposition patterns were examined in cases where one or both mirrors were powered. Erosion occurred primarily where a powered mirror faces a grounded surface, whereas overlapping discharges in the dual-powered case resulted in low ion kinetic energy and preferential net deposition at the overlapping area. These observations were supported by one-dimensional simulations of plasma potential evolution under representative conditions. These results provide critical insight into RF plasma behaviour in fully magnetised, geometrically asymmetric discharges and support the development of robust in-situ cleaning strategies for ITER optical diagnostics.
- Open Access
- 1 September 2025
- Published by AIP Publishing in Physics of Plasmas
- Vol. 32 (9)
Measurements of RF plasma sheath thickness in magnetic field up to 500 mT using a floating spiral probe
The thickness of the radio frequency (RF) plasma sheath developing in front of a capacitively coupled electrode has been measured using a floating probe. The probe presented in this contribution is based on the floating loop probe first developed by Godyak et al. To study the sheath potential in a smaller vacuum vessel, the probe has been designed in a spiral shape to maximize its sheath capacitance while occupying a reduced volume. During the time oscillation of the sheath, the probe's position influences the time variation of the probe's floating potential, unveiling the sheath thickness. Due to the strong direct current (DC) bias developing on the electrode and the significant RF frequency compared to the plasma ion frequency, the ions responded to the time-averaged sheath electric field. The measured time-average sheath thickness was comparable to the existing DC models with and without a magnetic field for pressures ranging from 2 to 10 Pa. Within this range of pressure, the sheath thickness decreased from 13 to 5 mm, due to the density increase. In a magnetic field, the sheath potential drop decreased and the plasma density increased, leading to a reduction of the sheath size. With the spiral floating probe, no magnetic pre-sheaths were observed up to 500 mT as predicted by Ahedo criterion.
- 1 September 2025
- Published by AIP Publishing in Physics of Plasmas
- Vol. 32 (9)
Open AccessMeasurements of RF plasma sheath thickness in magnetic field up to 500 mT using a floating spiral probe
The thickness of the radio frequency (RF) plasma sheath developing in front of a capacitively coupled electrode has been measured using a floating probe. The probe presented in this contribution is based on the floating loop probe first developed by Godyak et al. To study the sheath potential in a smaller vacuum vessel, the probe has been designed in a spiral shape to maximize its sheath capacitance while occupying a reduced volume. During the time oscillation of the sheath, the probe's position influences the time variation of the probe's floating potential, unveiling the sheath thickness. Due to the strong direct current (DC) bias developing on the electrode and the significant RF frequency compared to the plasma ion frequency, the ions responded to the time-averaged sheath electric field. The measured time-average sheath thickness was comparable to the existing DC models with and without a magnetic field for pressures ranging from 2 to 10 Pa. Within this range of pressure, the sheath thickness decreased from 13 to 5 mm, due to the density increase. In a magnetic field, the sheath potential drop decreased and the plasma density increased, leading to a reduction of the sheath size. With the spiral floating probe, no magnetic pre-sheaths were observed up to 500 mT as predicted by Ahedo criterion.
- Open Access
Radio-frequency capacitively coupled plasma parameters evolution as a function of magnetic field strength
- Open Access
Radio-frequency capacitively coupled plasma parameters evolution as a function of magnetic field strength
The use of magnetic fields in low-temperature plasma physics is promising in numerous applications. The magnetic field acts on the kinetic of the plasma charged particles, drastically modifying the ion and electron trajectories in the plasma. The influence of the magnetic field strength on plasma parameters, like the plasma and the electrode potentials, was measured for different gases and pressures, evidencing a strong variation before saturating for high magnetic fields. The saturation is connected to the variation of the ions and electrons collection area. It occurred when the magnetic field influence overcame the collisional effect, i.e. when the Larmor radius of ions became smaller than the ion mean free path. The electrostatic probe's floating potential saturation was a marker of ion magnetisation. Varying the pressure enabled collision cross-section calculation for magnetised discharges, leading to values consistent with the literature. Finally, the probe developed in this contribution allows almost independent measurement of perpendicular and parallel flux.
Open AccessRadio-frequency capacitively coupled plasma parameters evolution as a function of magnetic field strength
The use of magnetic fields in low-temperature plasma physics is promising in numerous applications. The magnetic field acts on the kinetic of the plasma charged particles, drastically modifying the ion and electron trajectories in the plasma. The influence of the magnetic field strength on plasma parameters, like the plasma and the electrode potentials, was measured for different gases and pressures, evidencing a strong variation before saturating for high magnetic fields. The saturation is connected to the variation of the ions and electrons collection area. It occurred when the magnetic field influence overcame the collisional effect, i.e. when the Larmor radius of ions became smaller than the ion mean free path. The electrostatic probe's floating potential saturation was a marker of ion magnetisation. Varying the pressure enabled collision cross-section calculation for magnetised discharges, leading to values consistent with the literature. Finally, the probe developed in this contribution allows almost independent measurement of perpendicular and parallel flux.
- Open Access
- 8 October 2024
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 41
Simulated temperature of a tungsten spot facing large plasma heat loads
- 8 October 2024
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 41
Open AccessSimulated temperature of a tungsten spot facing large plasma heat loads
- Open Access
- 1 July 2024
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 33 (7) , 075019
Variations of plasma potential in RF discharges with DC-grounded electrode
The self-bias voltage V bias and the plasma potential V p are the key parameters to control plasma-wall interactions in radio-frequency (RF) asymmetric plasma discharges. Knowing these two parameters allows to monitor the ion energy distribution on the electrode surface. However, in a direct current (DC) coupled plasma, the plasma potential increased to hundreds of volts while no more V bias developed on the driven electrode. In addition, the plasma potential is strongly impacted by the electrode-wall area ratio. Several analytical or semi-analytical models exist to explain this phenomenon and to approximate the plasma potential, knowing the electrode-wall area ratio considering capacitive sheaths or a combination of resistive and capacitive sheaths. The V p and several other plasma parameters were investigated experimentally with a Langmuir probe and a Retarding field energy analyser for different electrode/wall area ratios in low-temperature RF plasma. The validity of the models was studied for an extensive range of area ratios with different pressures and RF driving amplitude. Moreover, the presence of strong stochastic heating of the plasma for area ratios below 6 was evidenced by an increased ion flux and an increased electron temperature.
- 1 July 2024
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 33 (7) , 075019
Open AccessVariations of plasma potential in RF discharges with DC-grounded electrode
The self-bias voltage V bias and the plasma potential V p are the key parameters to control plasma-wall interactions in radio-frequency (RF) asymmetric plasma discharges. Knowing these two parameters allows to monitor the ion energy distribution on the electrode surface. However, in a direct current (DC) coupled plasma, the plasma potential increased to hundreds of volts while no more V bias developed on the driven electrode. In addition, the plasma potential is strongly impacted by the electrode-wall area ratio. Several analytical or semi-analytical models exist to explain this phenomenon and to approximate the plasma potential, knowing the electrode-wall area ratio considering capacitive sheaths or a combination of resistive and capacitive sheaths. The V p and several other plasma parameters were investigated experimentally with a Langmuir probe and a Retarding field energy analyser for different electrode/wall area ratios in low-temperature RF plasma. The validity of the models was studied for an extensive range of area ratios with different pressures and RF driving amplitude. Moreover, the presence of strong stochastic heating of the plasma for area ratios below 6 was evidenced by an increased ion flux and an increased electron temperature.
- Open Access
- 1 March 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (3)
Publisher’s Note: “Laser temperature programmed desorption: A flexible technique to study ion-surface interaction” [Rev. Sci. Instrum. 95, 033004 (2024)]
This article was originally published online on 7 March 2024 with information missing from the Acknowledgments section. The following copy has been reinsta This article was originally published online on 7 March 2024 with information missing from the Acknowledgments section. The following copy has been reinsta
- 1 March 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (3)
Open AccessPublisher’s Note: “Laser temperature programmed desorption: A flexible technique to study ion-surface interaction” [Rev. Sci. Instrum. 95, 033004 (2024)]
This article was originally published online on 7 March 2024 with information missing from the Acknowledgments section. The following copy has been reinsta This article was originally published online on 7 March 2024 with information missing from the Acknowledgments section. The following copy has been reinsta