Oleksiy Petrenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Oleksiy Petrenko has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Artur Onyshchenko
National Transport University
3 shared publications - Svitlana Vikhot
Lviv Polytechnic National University
3 shared publications - Vitalii Kovalchuk
Lviv Polytechnic National University
3 shared publications - Andriy Pentsak
Lviv Polytechnic National University
2 shared publications - Ivan Kravets
Lviv Polytechnic National University
2 shared publications - Dmytro Sydorak
Lviv Polytechnic National University
1 shared publication
Latest Publications
- 28 August 2026
- Published by Springer Nature
- p. 443-451
The Depth of Impregnation of Linseed Oil with a Siccative into Wood Along and Across the Fibers
- 28 August 2026
- Published by Springer Nature
- p. 443-451
The Depth of Impregnation of Linseed Oil with a Siccative into Wood Along and Across the Fibers
- 30 October 2025
- Published by Springer Nature
- p. 237-244
Operation of Silor-Modified Wood in Acidic Environments: An Experimental Study
- 30 October 2025
- Published by Springer Nature
- p. 237-244
Operation of Silor-Modified Wood in Acidic Environments: An Experimental Study
- Open Access
- 30 June 2025
- Published by Lutsk National Technical University in Сучасні технології та методи розрахунків у будівництві
- No. 23,p. 395-402
Особливості роботи модифікованої епоксидною смолою деревини хвойних порід
У статті розглянуто удосконалення способів модифікації деревини епоксидною смолою, наведено результати проведення експериментальних досліджень модифікованих епоксидною смолою деревини сосни, модрини та ялини на стиск вздовж волокон, встановлено оцінку впливу даної полімерної композиції на міцність деревини та проаналізовано особливості характеру їх роботи. Фізико-механічні властивості необробленої деревини є мінливими і залежать від багатьох зовнішніх факторів. Для стабілізації даних показників застосовується модифікація деревини різними способами. Деревина, піддана модифікації, стає більш стійкою до агресивних чинників і міцнішою. Способи її обробки включають використання модифікаторів різного хімічного складу. Розглянуто переваги епоксидної смоли. Метою наших досліджень є удосконалення способів модифікації деревини епоксидною смолою, проведення експериментальних досліджень модифікованих епоксидною смолою деревини сосни, модрини та ялини на стиск вздовж волокон, оцінка впливу даної полімерної композиції на міцність деревини та особливості характеру їх роботи. Удосконалено способи модифікації деревини епоксидними смолами. Наведено методику експериментальних натурних випробувань досліджуваних порід деревини. Встановлено особливості та характер роботи модифікованої та немодифікованої деревини хвойних порід: сосни, модрини, ялини. Отримано нові експериментальні дані, що стосується модифікованих епоксидною смолою зразків деревини на стиск вздовж волокон щодо її міцнісних характеристик. Після проведення натурних експериментів було визначено міцність модифікованої та немодифікованої досліджуваних хвойних порід деревини. Встановлено, що міцність деревини після модифікації автоклавним способом збільшилась для призм деревини сосни в 1,29 рази, модрини – в 1,21 рази, ялини в 1,36 рази.
- 30 June 2025
- Published by Lutsk National Technical University in Сучасні технології та методи розрахунків у будівництві
- No. 23,p. 395-402
Open AccessОсобливості роботи модифікованої епоксидною смолою деревини хвойних порід
У статті розглянуто удосконалення способів модифікації деревини епоксидною смолою, наведено результати проведення експериментальних досліджень модифікованих епоксидною смолою деревини сосни, модрини та ялини на стиск вздовж волокон, встановлено оцінку впливу даної полімерної композиції на міцність деревини та проаналізовано особливості характеру їх роботи. Фізико-механічні властивості необробленої деревини є мінливими і залежать від багатьох зовнішніх факторів. Для стабілізації даних показників застосовується модифікація деревини різними способами. Деревина, піддана модифікації, стає більш стійкою до агресивних чинників і міцнішою. Способи її обробки включають використання модифікаторів різного хімічного складу. Розглянуто переваги епоксидної смоли. Метою наших досліджень є удосконалення способів модифікації деревини епоксидною смолою, проведення експериментальних досліджень модифікованих епоксидною смолою деревини сосни, модрини та ялини на стиск вздовж волокон, оцінка впливу даної полімерної композиції на міцність деревини та особливості характеру їх роботи. Удосконалено способи модифікації деревини епоксидними смолами. Наведено методику експериментальних натурних випробувань досліджуваних порід деревини. Встановлено особливості та характер роботи модифікованої та немодифікованої деревини хвойних порід: сосни, модрини, ялини. Отримано нові експериментальні дані, що стосується модифікованих епоксидною смолою зразків деревини на стиск вздовж волокон щодо її міцнісних характеристик. Після проведення натурних експериментів було визначено міцність модифікованої та немодифікованої досліджуваних хвойних порід деревини. Встановлено, що міцність деревини після модифікації автоклавним способом збільшилась для призм деревини сосни в 1,29 рази, модрини – в 1,21 рази, ялини в 1,36 рази.
- Open Access
- 31 August 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (7 (124)) , 43-53
Assessing the stresses and magnitude of plastic hinge in a tunnel conduit made of precast metal corrugated structures taking into account the soil backfill parameters
The object of research is a tunnel conduit made of star-shaped metal corrugated structures. The stresses and magnitude of the plastic hinge occurring in the metal corrugated structures of the tunnel conduit were investigated, taking into account the degree of compaction and the height of the soil backfill. It was established that when the height of the backfill above the tunnel conduit made of precast metal corrugated structures increases and the degree of compaction of the soil backfill decreases, there is an increase in the values of stresses and plastic hinge in metal structures. With the height of the backfill above the conduit equal to 2.75 m and the degree of compaction of the soil backfill RP=80 %, stresses of 235.89 MPa are reached, exceeding the permissible 235 MPa. At the same time, the value of the plastic hinge is 1.03, which exceeds the normative 1.0. It was established that at embankment heights above the tunnel conduit structures from 1.75 m to 2.0 m, the smallest difference in stresses and magnitude of the plastic hinge is observed. At RP=98 %, the stress difference is 0.66 MPa, and the value of the plastic hinge is 0.008. In the case of the height of the embankment above the conduit from 1.5 m to 1.75 m, the stress increase was 5.5 MPa, and the value of the plastic hinge – 0.031. When the embankment height increases from 2.0 m to 2.25 m, the stress difference is 7.57 MPa, and the value of the plastic hinge is 0.041. It was determined that when the height of the embankment above the conduit was increased by 1.0 m in the range from 0.75 m to 1.75 m, the stress difference at RP=98 % increased by 27.84 MPa. However, when the height was increased by 1.0 m in the range from 2.75 m to 3.75 m, the stress difference increased by 12.66 MPa. At the same time, the value of the plastic hinge at embankment heights from 0.75 m to 1.75 m increased by 0.139, and at embankment heights from 2.75 m to 3.75 m – by 0.093
- 31 August 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (7 (124)) , 43-53
Open AccessAssessing the stresses and magnitude of plastic hinge in a tunnel conduit made of precast metal corrugated structures taking into account the soil backfill parameters
The object of research is a tunnel conduit made of star-shaped metal corrugated structures. The stresses and magnitude of the plastic hinge occurring in the metal corrugated structures of the tunnel conduit were investigated, taking into account the degree of compaction and the height of the soil backfill. It was established that when the height of the backfill above the tunnel conduit made of precast metal corrugated structures increases and the degree of compaction of the soil backfill decreases, there is an increase in the values of stresses and plastic hinge in metal structures. With the height of the backfill above the conduit equal to 2.75 m and the degree of compaction of the soil backfill RP=80 %, stresses of 235.89 MPa are reached, exceeding the permissible 235 MPa. At the same time, the value of the plastic hinge is 1.03, which exceeds the normative 1.0. It was established that at embankment heights above the tunnel conduit structures from 1.75 m to 2.0 m, the smallest difference in stresses and magnitude of the plastic hinge is observed. At RP=98 %, the stress difference is 0.66 MPa, and the value of the plastic hinge is 0.008. In the case of the height of the embankment above the conduit from 1.5 m to 1.75 m, the stress increase was 5.5 MPa, and the value of the plastic hinge – 0.031. When the embankment height increases from 2.0 m to 2.25 m, the stress difference is 7.57 MPa, and the value of the plastic hinge is 0.041. It was determined that when the height of the embankment above the conduit was increased by 1.0 m in the range from 0.75 m to 1.75 m, the stress difference at RP=98 % increased by 27.84 MPa. However, when the height was increased by 1.0 m in the range from 2.75 m to 3.75 m, the stress difference increased by 12.66 MPa. At the same time, the value of the plastic hinge at embankment heights from 0.75 m to 1.75 m increased by 0.139, and at embankment heights from 2.75 m to 3.75 m – by 0.093
- Open Access
- 30 June 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7(117)) , 50-58
Determining the strained state of prefabricated metal corrugated structures of a tunnel overpass exposed to the dynamic loading from railroad rolling stock
This paper reports the analysis of prospects for the use of prefabricated metal corrugated structures in the body of the embankment of a railroad track in the form of a tunnel overpass in order to pass road vehicles and railroad rolling stock. A technique of inertial dynamic tests of the deformed state of a tunnel overpass from prefabricated metal corrugated structures during the passage of railroad rolling stock is given, by measuring accelerations at the top and on the sides of overpass structures. An algorithm is proposed for processing the acceleration signal for assessing the strained state of metal corrugated structures of a tunnel overpass under the action of dynamic load from railroad transport. Experimental dynamic measurements of accelerations arising at the top and on the sides of a tunnel overpass during the passage of passenger and freight railroad rolling stock were carried out. The maximum value of accelerations arising at the top of a tunnel overpass during the passage of a freight train was 7.99 m/s2, and when passing a passenger train – 6.21 m/s2; the maximum accelerations that occur on the sides were 2.63 m/s2 and 1.77 m/s2. It is established that the maximum deformations of metal corrugated structures of the top of a tunnel overpass, when passing freight and passenger trains are, respectively, 1.63 mm and 1.11 mm. The maximum strains of metal corrugated structures on the sides of an overpass are 1.07 mm and 0.48 mm. The value of relative deformations in the vertical and horizontal dimensions of the structures of a tunnel overpass under the action of dynamic loads from the railroad rolling stock has been found. The relative vertical strains of an overpass amounted to 0.020 %; horizontal – 0.012 %. The practical significance of this work is that with the help of the devised procedure for measuring accelerations, it is possible to assess the strained state of metal corrugated structures under the influence of dynamic loads from the railroad rolling stock Проведено аналіз перспектив застосування збірних металевих гофрованих конструкцій у тілі насипу залізничної колії у вигляді тунельного шляхопроводу з метою пропуску автомобільних транспортних засобів та рухомого складу залізниць. Наведено спосіб інерційних динамічних випробувань деформованого стану тунельного шляхопроводу із збірних металевих гофрованих конструкцій при проїзді рухомого складу залізничного транспорту, шляхом вимірювання прискорень у вершині та на бокових сторонах конструкцій шляхопроводу. Запропоновано алгоритм обробки сигналу прискорень для оцінки деформованого стану металевих гофрованих конструкцій тунельного шляхопроводу при дії динамічного навантаження від залізничного транспорту. Проведено експериментальні динамічні вимірювання прискорень, що виникають у вершині та на бокових сторонах тунельного шляхопроводу при проїзді пасажирського та вантажного рухомого складу залізничного транспорту. Максимальна величина прискорень, що виникають у вершині тунельного шляхопроводу при проїзді вантажного поїзду склала 7,99 м/с2, а при проїзді пасажирського поїзду – 6,21 м/с2, а максимальні прискорення, які виникають на бокових сторонах становили 2,63 м/с2 та 1,77 м/с2. Встановлено, що максимальні деформації металевих гофрованих конструкцій вершини тунельного шляхопроводу, при проїзді вантажного та пасажирського поїздів становлять, відповідно, 1,63 мм та 1,11 мм. Максимальні деформації металевих гофрованих конструкцій на бокових сторонах шляхопроводу становлять 1,07 мм та 0,48 мм. Отримано величину відносних деформацій вертикального та горизонтального розмірів конструкцій тунельного шляхопроводу при дії динамічних навантажень від рухомого складу залізниці. Відносні вертикальні деформації шляхопроводу склали 0,020 %, а горизонтальні – 0,012 %. Практичне значення роботи полягає у тому, що за допомогою розробленої методики вимірювання прискорень можна проводити оцінку деформованого стану металевих гофрованих конструкцій при дії динамічних навантажень від рухомого складу залізниці
- 30 June 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7(117)) , 50-58
Open AccessDetermining the strained state of prefabricated metal corrugated structures of a tunnel overpass exposed to the dynamic loading from railroad rolling stock
This paper reports the analysis of prospects for the use of prefabricated metal corrugated structures in the body of the embankment of a railroad track in the form of a tunnel overpass in order to pass road vehicles and railroad rolling stock. A technique of inertial dynamic tests of the deformed state of a tunnel overpass from prefabricated metal corrugated structures during the passage of railroad rolling stock is given, by measuring accelerations at the top and on the sides of overpass structures. An algorithm is proposed for processing the acceleration signal for assessing the strained state of metal corrugated structures of a tunnel overpass under the action of dynamic load from railroad transport. Experimental dynamic measurements of accelerations arising at the top and on the sides of a tunnel overpass during the passage of passenger and freight railroad rolling stock were carried out. The maximum value of accelerations arising at the top of a tunnel overpass during the passage of a freight train was 7.99 m/s2, and when passing a passenger train – 6.21 m/s2; the maximum accelerations that occur on the sides were 2.63 m/s2 and 1.77 m/s2. It is established that the maximum deformations of metal corrugated structures of the top of a tunnel overpass, when passing freight and passenger trains are, respectively, 1.63 mm and 1.11 mm. The maximum strains of metal corrugated structures on the sides of an overpass are 1.07 mm and 0.48 mm. The value of relative deformations in the vertical and horizontal dimensions of the structures of a tunnel overpass under the action of dynamic loads from the railroad rolling stock has been found. The relative vertical strains of an overpass amounted to 0.020 %; horizontal – 0.012 %. The practical significance of this work is that with the help of the devised procedure for measuring accelerations, it is possible to assess the strained state of metal corrugated structures under the influence of dynamic loads from the railroad rolling stock Проведено аналіз перспектив застосування збірних металевих гофрованих конструкцій у тілі насипу залізничної колії у вигляді тунельного шляхопроводу з метою пропуску автомобільних транспортних засобів та рухомого складу залізниць. Наведено спосіб інерційних динамічних випробувань деформованого стану тунельного шляхопроводу із збірних металевих гофрованих конструкцій при проїзді рухомого складу залізничного транспорту, шляхом вимірювання прискорень у вершині та на бокових сторонах конструкцій шляхопроводу. Запропоновано алгоритм обробки сигналу прискорень для оцінки деформованого стану металевих гофрованих конструкцій тунельного шляхопроводу при дії динамічного навантаження від залізничного транспорту. Проведено експериментальні динамічні вимірювання прискорень, що виникають у вершині та на бокових сторонах тунельного шляхопроводу при проїзді пасажирського та вантажного рухомого складу залізничного транспорту. Максимальна величина прискорень, що виникають у вершині тунельного шляхопроводу при проїзді вантажного поїзду склала 7,99 м/с2, а при проїзді пасажирського поїзду – 6,21 м/с2, а максимальні прискорення, які виникають на бокових сторонах становили 2,63 м/с2 та 1,77 м/с2. Встановлено, що максимальні деформації металевих гофрованих конструкцій вершини тунельного шляхопроводу, при проїзді вантажного та пасажирського поїздів становлять, відповідно, 1,63 мм та 1,11 мм. Максимальні деформації металевих гофрованих конструкцій на бокових сторонах шляхопроводу становлять 1,07 мм та 0,48 мм. Отримано величину відносних деформацій вертикального та горизонтального розмірів конструкцій тунельного шляхопроводу при дії динамічних навантажень від рухомого складу залізниці. Відносні вертикальні деформації шляхопроводу склали 0,020 %, а горизонтальні – 0,012 %. Практичне значення роботи полягає у тому, що за допомогою розробленої методики вимірювання прискорень можна проводити оцінку деформованого стану металевих гофрованих конструкцій при дії динамічних навантажень від рухомого складу залізниці
- 22 June 2021
- Published by Lviv Polytechnic National University in Theory and Building Practice
- Vol. 2021 (1) , 64-71
ANALYSIS OF CALCULATION REGULATION METHODS IN STEEL COMBINED TRUSSES
The article is devoted to the calculated regulation of the stress deformation state (SDS) of combined steel trusses, which allows to reduce the efforts in some sections of the structure by increasing the efforts in other and design evenly stressed structures as the most rational systems. It is shown that the calculated method of SDS regulation makes it possible to reduce steel consumption by up to 34%. Four methods of calculated SDS regulation are proposed. The advantages of combined structures are given: the concentration of materials and the possibility of designing them as low-element. As shown in the example, for the quantitative criterion of quality it is possible to use rationally the maximum potential energy of deformation. Dependences for calculation of the maximum potential energy of compressed stretched, and compressed-bent elements of rod-bearing steel structures are given.
- 22 June 2021
- Published by Lviv Polytechnic National University in Theory and Building Practice
- Vol. 2021 (1) , 64-71
ANALYSIS OF CALCULATION REGULATION METHODS IN STEEL COMBINED TRUSSES
The article is devoted to the calculated regulation of the stress deformation state (SDS) of combined steel trusses, which allows to reduce the efforts in some sections of the structure by increasing the efforts in other and design evenly stressed structures as the most rational systems. It is shown that the calculated method of SDS regulation makes it possible to reduce steel consumption by up to 34%. Four methods of calculated SDS regulation are proposed. The advantages of combined structures are given: the concentration of materials and the possibility of designing them as low-element. As shown in the example, for the quantitative criterion of quality it is possible to use rationally the maximum potential energy of deformation. Dependences for calculation of the maximum potential energy of compressed stretched, and compressed-bent elements of rod-bearing steel structures are given.
- Open Access
- 26 February 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (5 (109)) , 6-15
Devising a procedure for assessing the subgrade compaction degree based on the propagation rate of elastic waves
This paper reports the analysis of the methods for estimating the technical condition of the subgrade underneath a constructed railroad track or road during its operation. The study results have proven that the issue related to monitoring and controlling high-quality compaction of a heterogeneous subgrade remains relevant and requires the construction of reliable experimental methods for assessing the subgrade degree of compaction. A procedure for determining the compaction of subgrade in the laboratory has been devised, based on inertial microcomputer technologies, which makes it possible to assess the degree of compaction of subgrade soils depending on the propagation rate of an impact's elastic waves. An experimental study has been performed into the propagation rate of elastic waves across a homogeneous subgrade made of coarse-grained sand and a heterogeneous subgrade made of coarse sand with a layer of clay in the middle of the prism. The study results established that the propagation rate of an elastic wave in a heterogeneous subgrade accepts a lower value than the rate of wave propagation in a homogeneous subgrade. Through the dynamic interpretation, by using a discriminant statistical analysis, the characteristic features have been defined in the distribution of accelerations in the body of the homogeneous and heterogeneous subgrade, depending on the degree of compaction, which would make it possible to monitor the state of the subgrade during operation. As the degree of the subgrade soil compaction affects the technical condition of roads
- 26 February 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (5 (109)) , 6-15
Open AccessDevising a procedure for assessing the subgrade compaction degree based on the propagation rate of elastic waves
This paper reports the analysis of the methods for estimating the technical condition of the subgrade underneath a constructed railroad track or road during its operation. The study results have proven that the issue related to monitoring and controlling high-quality compaction of a heterogeneous subgrade remains relevant and requires the construction of reliable experimental methods for assessing the subgrade degree of compaction. A procedure for determining the compaction of subgrade in the laboratory has been devised, based on inertial microcomputer technologies, which makes it possible to assess the degree of compaction of subgrade soils depending on the propagation rate of an impact's elastic waves. An experimental study has been performed into the propagation rate of elastic waves across a homogeneous subgrade made of coarse-grained sand and a heterogeneous subgrade made of coarse sand with a layer of clay in the middle of the prism. The study results established that the propagation rate of an elastic wave in a heterogeneous subgrade accepts a lower value than the rate of wave propagation in a homogeneous subgrade. Through the dynamic interpretation, by using a discriminant statistical analysis, the characteristic features have been defined in the distribution of accelerations in the body of the homogeneous and heterogeneous subgrade, depending on the degree of compaction, which would make it possible to monitor the state of the subgrade during operation. As the degree of the subgrade soil compaction affects the technical condition of roads
- 1 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1127-1130
Eavesdropping-resilient wireless communication system based on modified OFDM/QAM air interface
Modern military communication systems are currently facing an important issue with the security. The rapid technological development provides us with the new advanced weaponry, including robots and unmanned vehicles, which rely on the communication system in background. Thus, it is important to provide the reliable and secure wireless communications channels, which are resilient to intrusions and data interceptions by enemies. In this paper, we propose a new approach for signal modulation based on the conventional orthogonal frequency division multiplexing and quadrature amplitude modulation. The novelty of this scheme is that only one signal component is physically transmitted through the channel, while other is added in the received according to the specific rules. Receiver adds the second component taking into account received signal amplitude, subcarrier index and data transmission mode. All possible combinations of these parameters are summarized in the mapping table, which is known only by transmitter and receiver. We propose multiple combinations of the proposed modulation scheme, which differs in terms of spectral efficiency, energy efficiency and security. Moreover, proposed approach provides opportunity to mix the signal within the large set of available subcarriers and create thousands possible options to confuse the eavesdropper. Simulations have been conducted to assess the performance of the proposed modulation waveforms over non-line-of-sight channels. Simulation results show that proposed quadrature amplitude modulation provides better performance in terms of bit error rate due to the absence of IQ-imbalance and phase noises in the modified waveforms.
- 1 February 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1127-1130
Eavesdropping-resilient wireless communication system based on modified OFDM/QAM air interface
Modern military communication systems are currently facing an important issue with the security. The rapid technological development provides us with the new advanced weaponry, including robots and unmanned vehicles, which rely on the communication system in background. Thus, it is important to provide the reliable and secure wireless communications channels, which are resilient to intrusions and data interceptions by enemies. In this paper, we propose a new approach for signal modulation based on the conventional orthogonal frequency division multiplexing and quadrature amplitude modulation. The novelty of this scheme is that only one signal component is physically transmitted through the channel, while other is added in the received according to the specific rules. Receiver adds the second component taking into account received signal amplitude, subcarrier index and data transmission mode. All possible combinations of these parameters are summarized in the mapping table, which is known only by transmitter and receiver. We propose multiple combinations of the proposed modulation scheme, which differs in terms of spectral efficiency, energy efficiency and security. Moreover, proposed approach provides opportunity to mix the signal within the large set of available subcarriers and create thousands possible options to confuse the eavesdropper. Simulations have been conducted to assess the performance of the proposed modulation waveforms over non-line-of-sight channels. Simulation results show that proposed quadrature amplitude modulation provides better performance in terms of bit error rate due to the absence of IQ-imbalance and phase noises in the modified waveforms.