Sadegh Ahmadi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sadegh Ahmadi has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
Mahla Gharahasanlo
Center of Excellence in Design and Optimization of Energy Systems (CEDOES), School of Mechanical Engineering, College of Engineering, University of Tehran, P.O. Box: 11155-4563, Tehran, Iran
2 shared publications- Mohammad Ali Akhavan-Behabadi
Center of Excellence in Design and Optimization of Energy Systems (CEDOES), School of Mechanical Engineering, College of Engineering, University of Tehran, P.O. Box: 11155-4563, Tehran, Iran
2 shared publications - Pedram Hanafizadeh
University of Tehran
2 shared publications Shahab Zeraati
Center of Excellence in Design and Optimization of Energy Systems (CEDOES), School of Mechanical Engineering, College of Engineering, University of Tehran, P.O. Box: 11155-4563, Tehran, Iran
2 shared publicationsShahide Sayadian
2 shared publicationsA.J. Robinson
1 shared publication
Latest Publications
- Open Access
- 21 March 2026
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 199
Numerical investigation of contact-line mobility effects on the oscillation of a viscous sessile drop
- 21 March 2026
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 199
Open AccessNumerical investigation of contact-line mobility effects on the oscillation of a viscous sessile drop
- 12 September 2024
- Published by Springer Nature in Flow, Turbulence and Combustion
- Vol. 114 (1) , 299-322
Numerical Simulation of Hydrodynamic Noises during Bubble Rising Process
- 12 September 2024
- Published by Springer Nature in Flow, Turbulence and Combustion
- Vol. 114 (1) , 299-322
Numerical Simulation of Hydrodynamic Noises during Bubble Rising Process
- 1 May 2021
- Published by Elsevier in Accident Analysis & Prevention
- Vol. 154, 106065
The effectiveness of different types of motorcycle helmets – A scoping review
- 1 May 2021
- Published by Elsevier in Accident Analysis & Prevention
- Vol. 154, 106065
The effectiveness of different types of motorcycle helmets – A scoping review
- 11 January 2020
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 143 (1) , 473-483
Performance analysis of an integrated cooling system consisted of earth-to-air heat exchanger (EAHE) and water spray channel
- 11 January 2020
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 143 (1) , 473-483
Performance analysis of an integrated cooling system consisted of earth-to-air heat exchanger (EAHE) and water spray channel
- 1 July 2017
- Published by Elsevier in Applied Thermal Engineering
- Vol. 122, 503-514
Effect of external electrode arrangements on R-134a two-phase flow regimes in the presence of AC electric fields
- 1 July 2017
- Published by Elsevier in Applied Thermal Engineering
- Vol. 122, 503-514
Effect of external electrode arrangements on R-134a two-phase flow regimes in the presence of AC electric fields
- 1 August 2016
- Published by Elsevier in Journal of Electrostatics
- Vol. 82, 63-71
Numerical investigation of EHD effects on heat transfer enhancement and flow pattern of R-134a two phase flow
- 1 August 2016
- Published by Elsevier in Journal of Electrostatics
- Vol. 82, 63-71
Numerical investigation of EHD effects on heat transfer enhancement and flow pattern of R-134a two phase flow
- 1 November 2013
- Published by SAGE Publications in Materials Science and Technology
- Vol. 29 (11) , 1297-1303
Subgrain growth in presence of nanosized dispersoids in Al–4·5Zn–1Mg alloy
In this paper, an analytical model for subgrain growth in the presence of nanosized dispersoids is presented. The growth rate of subgrains is correlated to the mobility of low angle grain boundaries (LAGBs) and the net driving force for growth. The driving force is considered as the difference between stored energy, being inversely proportional to the average subgrain size, and the Zener drag pressure. A material dependent constant necessary for the determination of the mobility of LAGBs is estimated by fitting the model predictions into the experimental results. Model predictions of the evolution of subgrain sizes with annealing time at different temperatures show that subgrain growth intensifies with increasing annealing temperature. The magnitude of the Zener drag pressure has a predefined effect on the subgrain growth rate. The model predicts that when the PZ/ γs ratio is smaller than 1 μm−1, the Zener drag pressure has an effect on subgrain size and the subgrain growth rate tends to decrease. However, when the PZ/ γs ratio is larger than 1 μm−1, there is a limit beyond which the subgrain size does not increase with increasing annealing time. The limiting subgrain size is a function of the surface boundary energy and Zener drag pressure.
- 1 November 2013
- Published by SAGE Publications in Materials Science and Technology
- Vol. 29 (11) , 1297-1303
Subgrain growth in presence of nanosized dispersoids in Al–4·5Zn–1Mg alloy
In this paper, an analytical model for subgrain growth in the presence of nanosized dispersoids is presented. The growth rate of subgrains is correlated to the mobility of low angle grain boundaries (LAGBs) and the net driving force for growth. The driving force is considered as the difference between stored energy, being inversely proportional to the average subgrain size, and the Zener drag pressure. A material dependent constant necessary for the determination of the mobility of LAGBs is estimated by fitting the model predictions into the experimental results. Model predictions of the evolution of subgrain sizes with annealing time at different temperatures show that subgrain growth intensifies with increasing annealing temperature. The magnitude of the Zener drag pressure has a predefined effect on the subgrain growth rate. The model predicts that when the PZ/ γs ratio is smaller than 1 μm−1, the Zener drag pressure has an effect on subgrain size and the subgrain growth rate tends to decrease. However, when the PZ/ γs ratio is larger than 1 μm−1, there is a limit beyond which the subgrain size does not increase with increasing annealing time. The limiting subgrain size is a function of the surface boundary energy and Zener drag pressure.