Srihanum Adnan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Srihanum Adnan has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Nik Siti Mariam Nek Mat Din
Synthesis and Products Development Unit, Advanced Oleochemical Technology Division, Malaysian Palm Oil Board, Kajang, Malaysia
2 shared publicationsYeong Shoot Kian
Synthesis and Products Development Unit, Advanced Oleochemical Technology Division, Malaysian Palm Oil Board, Kajang, Malaysia
2 shared publicationsHazimah Abu Hassan
Synthesis Product Development Unit, Advanced Oleochemical Technology Division, Malaysian Palm Oil Board, No. 6, Persiaran Institusi, Bandar Baru Bangi, 43000 Kajang, Selangor, Malaysia
1 shared publicationKosheela Devi Pp
Malaysian Palm Oil Board (MPOB)
1 shared publicationKosheela Pp Devi
Synthesis and Products Development Unit, Advanced Oleochemical Technology Division, Malaysian Palm Oil Board, Kajang, Malaysia
1 shared publicationMaznee Ti Tuan Noor
Synthesis and Products Development Unit, Advanced Oleochemical Technology Division, Malaysian Palm Oil Board, Kajang, Malaysia
1 shared publication
Latest Publications
- 13 April 2026
- Published by SAGE Publications in Journal of Cellular Plastics
Optimisation of bio-based viscoelastic polyurethane foam production using high-pressure machine technology: Impact of isocyanate indices
This study examines the impact of varying isocyanate indices on the morphology and properties of bio-based viscoelastic polyurethane (VE PU) foams produced using high-pressure processing and moulding technology. Palm-based polyol, referred to herein as Pioneer E-135, was used as a sustainable alternative to petroleum-based polyol. VE PU foams were formulated with different isocyanate indices (71%, 75%, 79% and 83%) and their physical, mechanical and morphological characteristics were evaluated. Results indicated that the VE PU foam containing 10% Pioneer-E135 polyol and an isocyanate index of 83% exhibited superior mechanical properties compared to the VE PU foam with 100% petroleum-based polyol. The incorporation of 10% Pioneer-E135 polyol significantly enhanced the mechanical properties, including surface texture, morphology and load-bearing capacity, as indicated by indentation force deflection and sag factor measurements. Higher NCO indices contributed to increased tensile strength, tear strength, and ageing resistance, but resulted in lower density and reduced elongation at break. Overall, the optimised processing parameters enabled the successful production of high-quality, bio-based VE PU foams using high-pressure machine technology.
- 13 April 2026
- Published by SAGE Publications in Journal of Cellular Plastics
Optimisation of bio-based viscoelastic polyurethane foam production using high-pressure machine technology: Impact of isocyanate indices
This study examines the impact of varying isocyanate indices on the morphology and properties of bio-based viscoelastic polyurethane (VE PU) foams produced using high-pressure processing and moulding technology. Palm-based polyol, referred to herein as Pioneer E-135, was used as a sustainable alternative to petroleum-based polyol. VE PU foams were formulated with different isocyanate indices (71%, 75%, 79% and 83%) and their physical, mechanical and morphological characteristics were evaluated. Results indicated that the VE PU foam containing 10% Pioneer-E135 polyol and an isocyanate index of 83% exhibited superior mechanical properties compared to the VE PU foam with 100% petroleum-based polyol. The incorporation of 10% Pioneer-E135 polyol significantly enhanced the mechanical properties, including surface texture, morphology and load-bearing capacity, as indicated by indentation force deflection and sag factor measurements. Higher NCO indices contributed to increased tensile strength, tear strength, and ageing resistance, but resulted in lower density and reduced elongation at break. Overall, the optimised processing parameters enabled the successful production of high-quality, bio-based VE PU foams using high-pressure machine technology.
- 4 January 2022
- Published by SAGE Publications in Journal of Cellular Plastics
- Vol. 58 (3) , 485-503
Low density rigid polyurethane foam incorporated with renewable polyol as sustainable thermal insulation material
Palm olein-based polyol (PP) was used as a partial replacement for commercial sucrose/glycerine initiated polyether polyol (GP) for the production of low density rigid polyurethane foams (RPUFs). The hydroxyl value (OHV) of the GP was 380 mg KOH/g, whereas the OHV for PP was 360 mg KOH/g. The RPUFs were prepared by replacing the GP with PP up to 50 parts per hundred parts of polyols (pph). Characterisation of the RPUFs, including density, compressive strength and strain, cell morphology and thermal conductivity ( k-value), were conducted. The dimensional stability of the foams was also evaluated. The study showed improvement in the compressive strength and strain for palm-based RPUFs with the incorporation of up to 30 pph PP as compared to GP foams. The lowest k-value (0.0232 W/m.K) of RPUF with density below 30 kg/m3 was obtained with the incorporation of 10 pph PP. This was due to the smallest and uniform pore size distribution observed using SEM images. The dimensional stability of the RPUF prepared from PP was within the acceptable range. Thus, the RPUFs made from PP are potential candidates to be used as insulation for refrigerators, freezers and piping.
- 4 January 2022
- Published by SAGE Publications in Journal of Cellular Plastics
- Vol. 58 (3) , 485-503
Low density rigid polyurethane foam incorporated with renewable polyol as sustainable thermal insulation material
Palm olein-based polyol (PP) was used as a partial replacement for commercial sucrose/glycerine initiated polyether polyol (GP) for the production of low density rigid polyurethane foams (RPUFs). The hydroxyl value (OHV) of the GP was 380 mg KOH/g, whereas the OHV for PP was 360 mg KOH/g. The RPUFs were prepared by replacing the GP with PP up to 50 parts per hundred parts of polyols (pph). Characterisation of the RPUFs, including density, compressive strength and strain, cell morphology and thermal conductivity ( k-value), were conducted. The dimensional stability of the foams was also evaluated. The study showed improvement in the compressive strength and strain for palm-based RPUFs with the incorporation of up to 30 pph PP as compared to GP foams. The lowest k-value (0.0232 W/m.K) of RPUF with density below 30 kg/m3 was obtained with the incorporation of 10 pph PP. This was due to the smallest and uniform pore size distribution observed using SEM images. The dimensional stability of the RPUF prepared from PP was within the acceptable range. Thus, the RPUFs made from PP are potential candidates to be used as insulation for refrigerators, freezers and piping.
- Open Access
- 18 February 2016
- Published by Hindawi Limited in Advances in Materials Science and Engineering
- Vol. 2016, 1-12
Development of Flexible Polyurethane Nanostructured Biocomposite Foams Derived from Palm Olein-Based Polyol
This study examined the effect of organoclay montmorillonite (OMMT) on the mechanical properties and morphology of flexible polyurethane/OMMT nanocomposite (PU/OMMT) foams prepared from petroleum- and palm olein-based polyols. Palm-based PU foams exhibited inferior mechanical strength as compared to neat petroleum PU foams. However, addition of OMMT significantly improved the foams strength of flexible polyurethane/OMMT nanocomposite foams prepared from palm olein-based polyol (PU bionanocomposite foam). The morphology analysed by scanning electron microscopy (SEM) showed that the cell size of the foam decreased with increasing OMMT content. PU bionanocomposite foam with 5 wt% of OMMT had the most improved tensile (63%) and tear (48%) strengths compared to its neat counterpart. Transmission electron microscopy (TEM) revealed the exfoliated structure of the respective foam. It was concluded that OMMT improved mechanical properties and morphology of PU foams.
- 18 February 2016
- Published by Hindawi Limited in Advances in Materials Science and Engineering
- Vol. 2016, 1-12
Open AccessDevelopment of Flexible Polyurethane Nanostructured Biocomposite Foams Derived from Palm Olein-Based Polyol
This study examined the effect of organoclay montmorillonite (OMMT) on the mechanical properties and morphology of flexible polyurethane/OMMT nanocomposite (PU/OMMT) foams prepared from petroleum- and palm olein-based polyols. Palm-based PU foams exhibited inferior mechanical strength as compared to neat petroleum PU foams. However, addition of OMMT significantly improved the foams strength of flexible polyurethane/OMMT nanocomposite foams prepared from palm olein-based polyol (PU bionanocomposite foam). The morphology analysed by scanning electron microscopy (SEM) showed that the cell size of the foam decreased with increasing OMMT content. PU bionanocomposite foam with 5 wt% of OMMT had the most improved tensile (63%) and tear (48%) strengths compared to its neat counterpart. Transmission electron microscopy (TEM) revealed the exfoliated structure of the respective foam. It was concluded that OMMT improved mechanical properties and morphology of PU foams.