Yitu Lai
Research Subjects
Yitu Lai has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- Sheng Su
Xiamen Environment Protection Vehicle Emission Control Technology Center, Xiamen, 361023, China
5 shared publications - Yachao Wang
National Laboratory of Automotive Performance & Emission Test, School of Mechanical Engineering, Beijing Institute of Technology, Beijing, 100081, China
3 shared publications - Barouch Giechaskiel
European Commission, Joint Research Centre, 21027 Ispra, Italy
2 shared publications Pan Hou
Xiamen Environment Protection Vehicle Emission Control Technology Center, Xiamen, 361023, China
2 shared publications- Pan Hou
Xiamen Environment Protection Vehicle Emission Control Technology Center, Xiamen 361023, China
2 shared publications Sheng Su
Xiamen Environment Protection Vehicle Emission Control Technology Center, Xiamen, 361023, China; National Laboratory of Automotive Performance & Emission Test, Beijing Institute of Technology, Beijing, 100081, China
2 shared publications
Latest Publications
- Open Access
- 26 February 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (5) , 2250
Impact of Continuous-Regeneration Particulate Filters on Gaseous Pollutant Emissions of Diesel Engines
With increasingly stringent international limits on diesel particulate matter emissions, Continuous-Regeneration Particulate Filters (CRPFs) have been widely applied in heavy-duty vehicle (HDV) exhaust systems. However, their impacts on the complete gaseous pollutant profile remain insufficiently characterized. This study investigated the effects of three CRPF configurations on gaseous emissions from a China III diesel engine under the World Harmonized Transient Cycle (WHTC). Regulated pollutants (CO, total hydrocarbons (THC), NOx, and CO2) and unregulated pollutants (benzene series compounds and aldehydes) were measured before and after CRPF installation. The results demonstrated that CRPFs achieved high reduction efficiencies for CO (98.5–99.9%) and THC (77.4–99.9%) through catalytic oxidation, while showing negligible effects on NOx (0.2–3.0% reduction) and slight increases in CO2 (0.07–0.55%). For unregulated pollutants, aldehydes were effectively reduced (formaldehyde: 84.1–100.0%; acetaldehyde: 47.4–100.0%), whereas benzene series compounds exhibited variable responses, with some species showing increased emissions. These findings reveal complex pollutant transformation mechanisms within CRPF systems and provide references for optimizing aftertreatment configurations to meet China VI and subsequent emission standards, thereby contributing to the mitigation of air pollution, the protection of public health, and the promotion of sustainable societal development.
- 26 February 2026
- Published by MDPI AG in Sustainability
- Vol. 18 (5) , 2250
Open AccessImpact of Continuous-Regeneration Particulate Filters on Gaseous Pollutant Emissions of Diesel Engines
With increasingly stringent international limits on diesel particulate matter emissions, Continuous-Regeneration Particulate Filters (CRPFs) have been widely applied in heavy-duty vehicle (HDV) exhaust systems. However, their impacts on the complete gaseous pollutant profile remain insufficiently characterized. This study investigated the effects of three CRPF configurations on gaseous emissions from a China III diesel engine under the World Harmonized Transient Cycle (WHTC). Regulated pollutants (CO, total hydrocarbons (THC), NOx, and CO2) and unregulated pollutants (benzene series compounds and aldehydes) were measured before and after CRPF installation. The results demonstrated that CRPFs achieved high reduction efficiencies for CO (98.5–99.9%) and THC (77.4–99.9%) through catalytic oxidation, while showing negligible effects on NOx (0.2–3.0% reduction) and slight increases in CO2 (0.07–0.55%). For unregulated pollutants, aldehydes were effectively reduced (formaldehyde: 84.1–100.0%; acetaldehyde: 47.4–100.0%), whereas benzene series compounds exhibited variable responses, with some species showing increased emissions. These findings reveal complex pollutant transformation mechanisms within CRPF systems and provide references for optimizing aftertreatment configurations to meet China VI and subsequent emission standards, thereby contributing to the mitigation of air pollution, the protection of public health, and the promotion of sustainable societal development.
- Open Access
- 11 April 2023
- Published by MDPI AG in Atmosphere
- Vol. 14 (4) , 702
Evaluating the Measurement Uncertainty of On-Road NOx Using a Portable Emission Measurement System (PEMS) Based on Real Testing Data in China
An evaluation of the measurement uncertainty of on-road NOx emissions using portable emission measurement system (PEMS) based on real local testing data collected in China was carried out as per the type B method defined in the EN 17507 standard. The aim of this work was to quantify the “absolute” measurement uncertainty of PEMSs, which excluded “PEMS relative to laboratory constant volume sampler (CVS)” uncertainty from the calculation of on-road NOx measurement uncertainty using PEMSs. PEMS instruments from three mainstream manufacturers were employed. The zero drift of the NOx analyzers was evaluated periodically during the real driving emissions (RDE) test, and it was noticed that there was neither a linear nor step model of zero drift, with no correlation with the boundary conditions or measurement principle. Additionally, from the 256 valid RDE tests, the zero drift always ranged from 3.8 ppm to −3.8 ppm, and more than 95% of the span drifts were within a range of 1.5%. Based on the laboratory testing of ten vehicles using the worldwide harmonized light-duty vehicle test cycle (WLTC), the type B uncertainty of PEMS NOx measurements corresponding to China-6a and China-6b limits was assessed. An uncertainty of 26.5% for China-6a was found (NOx limit = 60 mg/km over the WLTC), which is very close to the 22.5% from the EU evaluation results (NOx limit = 80 mg/km over the WLTC); the uncertainty with respect to China-6b was found to be 42.8% because the type-I limit was tuned down to 35 mg/km. This result indicates that, with the ever-tightening regulatory limits of vehicle NOx emissions, big challenges will be posed in terms of the reliability of PEMS measurements, which requires PEMS manufacturers to improve the performance of the instruments and policymakers to refine the test procedures and/or result calculation method to minimize the impacts.
- 11 April 2023
- Published by MDPI AG in Atmosphere
- Vol. 14 (4) , 702
Open AccessEvaluating the Measurement Uncertainty of On-Road NOx Using a Portable Emission Measurement System (PEMS) Based on Real Testing Data in China
An evaluation of the measurement uncertainty of on-road NOx emissions using portable emission measurement system (PEMS) based on real local testing data collected in China was carried out as per the type B method defined in the EN 17507 standard. The aim of this work was to quantify the “absolute” measurement uncertainty of PEMSs, which excluded “PEMS relative to laboratory constant volume sampler (CVS)” uncertainty from the calculation of on-road NOx measurement uncertainty using PEMSs. PEMS instruments from three mainstream manufacturers were employed. The zero drift of the NOx analyzers was evaluated periodically during the real driving emissions (RDE) test, and it was noticed that there was neither a linear nor step model of zero drift, with no correlation with the boundary conditions or measurement principle. Additionally, from the 256 valid RDE tests, the zero drift always ranged from 3.8 ppm to −3.8 ppm, and more than 95% of the span drifts were within a range of 1.5%. Based on the laboratory testing of ten vehicles using the worldwide harmonized light-duty vehicle test cycle (WLTC), the type B uncertainty of PEMS NOx measurements corresponding to China-6a and China-6b limits was assessed. An uncertainty of 26.5% for China-6a was found (NOx limit = 60 mg/km over the WLTC), which is very close to the 22.5% from the EU evaluation results (NOx limit = 80 mg/km over the WLTC); the uncertainty with respect to China-6b was found to be 42.8% because the type-I limit was tuned down to 35 mg/km. This result indicates that, with the ever-tightening regulatory limits of vehicle NOx emissions, big challenges will be posed in terms of the reliability of PEMS measurements, which requires PEMS manufacturers to improve the performance of the instruments and policymakers to refine the test procedures and/or result calculation method to minimize the impacts.
- Open Access
- 30 March 2023
- Published by MDPI AG in Atmosphere
- Vol. 14 (4) , 651
Machine Learning-Aided Remote Monitoring of NOx Emissions from Heavy-Duty Diesel Vehicles Based on OBD Data Streams
Most of the current, popular approaches to monitoring real driving NOx emissions are based on direct measurement. However, due to the uncertainty of sensor-based measurements, such methods cannot always be used to accurately screen out the malfunctions of an emission control system. In this paper, a random forest (RF) model which extracts information from on-board diagnostics (OBD) data streams transmitted by a remote emission management vehicle terminal (REMVT) is proposed to provide a specific emission method for the online screening of high NOx emissions. First, two particular forms of modeling, random forest and logistic regression (LR), are laid out as representatives of nonparametric models and specified linear models. These two models were trained, validated and compared using OBD data collected from three China-VI heavy-duty diesel vehicles (HDDVs). The results show that as a data-driven, highly adaptive and robust learning method, the RF model can more accurately identify an abnormal emission state. Finally, a further validation was conducted, in which another China-VI HDDV was tested in two typical states, including a fault state and a normal state. The results indicated that the RF model could clearly distinguish the out-of-control emission condition from the normal operation state. The outcome of this research verifies the feasibility of using a machine learning model to process remote OBD data on HD vehicles and to identify high emissions in the case of an in-use fleet. On this basis, more sophisticated combined models and multi-stage models could be developed.
- 30 March 2023
- Published by MDPI AG in Atmosphere
- Vol. 14 (4) , 651
Open AccessMachine Learning-Aided Remote Monitoring of NOx Emissions from Heavy-Duty Diesel Vehicles Based on OBD Data Streams
Most of the current, popular approaches to monitoring real driving NOx emissions are based on direct measurement. However, due to the uncertainty of sensor-based measurements, such methods cannot always be used to accurately screen out the malfunctions of an emission control system. In this paper, a random forest (RF) model which extracts information from on-board diagnostics (OBD) data streams transmitted by a remote emission management vehicle terminal (REMVT) is proposed to provide a specific emission method for the online screening of high NOx emissions. First, two particular forms of modeling, random forest and logistic regression (LR), are laid out as representatives of nonparametric models and specified linear models. These two models were trained, validated and compared using OBD data collected from three China-VI heavy-duty diesel vehicles (HDDVs). The results show that as a data-driven, highly adaptive and robust learning method, the RF model can more accurately identify an abnormal emission state. Finally, a further validation was conducted, in which another China-VI HDDV was tested in two typical states, including a fault state and a normal state. The results indicated that the RF model could clearly distinguish the out-of-control emission condition from the normal operation state. The outcome of this research verifies the feasibility of using a machine learning model to process remote OBD data on HD vehicles and to identify high emissions in the case of an in-use fleet. On this basis, more sophisticated combined models and multi-stage models could be developed.
- 29 June 2022
- Published by Elsevier in Chemosphere
- Vol. 306, 135522
Particle number emissions from fully warmed gasoline vehicles at various ambient temperatures
- 29 June 2022
- Published by Elsevier in Chemosphere
- Vol. 306, 135522
Particle number emissions from fully warmed gasoline vehicles at various ambient temperatures
- Open Access
- 26 May 2022
- Published by MDPI AG in Atmosphere
- Vol. 13 (6) , 872
Reproducibility of the 10-nm Solid Particle Number Methodology for Light-Duty Vehicles Exhaust Measurements
Many countries worldwide have introduced a limit for solid particles larger than 23 nm for the type approval of vehicles before their circulation in the market. However, for some vehicles, in particular for port fuel injection engines (gasoline and gas engines) a high fraction of particles resides below 23 nm. For this reason, a methodology for counting solid particles larger than 10 nm was developed in the Particle Measurement Programme (PMP) group of the United Nations Economic Commission for Europe (UNECE). There are no studies assessing the reproducibility of the new methodology across different laboratories. In this study we compared the reproducibility of the new 10 nm methodology to the current 23 nm methodology. A light-duty gasoline direct injection vehicle and two reference solid particle number measurement systems were circulated in seven European and two Asian laboratories which were also measuring with their own systems fulfilling the current 23 nm methodology. The hot and cold start emission of the vehicle covered a range of 1 to 15 × 1012 #/km with the ratio of sub-23 nm particles to the >23 nm emissions being 10–50%. In most cases the differences between the three measurement systems were ±10%. In general, the reproducibility of the new methodology was at the same levels (around 14%) as with the current methodology (on average 17%).
- 26 May 2022
- Published by MDPI AG in Atmosphere
- Vol. 13 (6) , 872
Open AccessReproducibility of the 10-nm Solid Particle Number Methodology for Light-Duty Vehicles Exhaust Measurements
Many countries worldwide have introduced a limit for solid particles larger than 23 nm for the type approval of vehicles before their circulation in the market. However, for some vehicles, in particular for port fuel injection engines (gasoline and gas engines) a high fraction of particles resides below 23 nm. For this reason, a methodology for counting solid particles larger than 10 nm was developed in the Particle Measurement Programme (PMP) group of the United Nations Economic Commission for Europe (UNECE). There are no studies assessing the reproducibility of the new methodology across different laboratories. In this study we compared the reproducibility of the new 10 nm methodology to the current 23 nm methodology. A light-duty gasoline direct injection vehicle and two reference solid particle number measurement systems were circulated in seven European and two Asian laboratories which were also measuring with their own systems fulfilling the current 23 nm methodology. The hot and cold start emission of the vehicle covered a range of 1 to 15 × 1012 #/km with the ratio of sub-23 nm particles to the >23 nm emissions being 10–50%. In most cases the differences between the three measurement systems were ±10%. In general, the reproducibility of the new methodology was at the same levels (around 14%) as with the current methodology (on average 17%).
- 1 December 2021
- Published by Elsevier in Environmental Pollution
- Vol. 290, 117984
Primary organic gas emissions from gasoline vehicles in China: Factors, composition and trends
- 1 December 2021
- Published by Elsevier in Environmental Pollution
- Vol. 290, 117984
Primary organic gas emissions from gasoline vehicles in China: Factors, composition and trends
- Open Access
- 1 August 2021
- Published by Elsevier in Journal of Aerosol Science
- Vol. 156
Particulate emissions of heavy duty diesel engines measured from the tailpipe and the dilution tunnel
- 1 August 2021
- Published by Elsevier in Journal of Aerosol Science
- Vol. 156
Open AccessParticulate emissions of heavy duty diesel engines measured from the tailpipe and the dilution tunnel