Hanwei Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hanwei Wang has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Kai Luo
School of Marine Science and Technology, Northwestern Polytechnical University, Xi’an 710072, Shaanxi, China
4 shared publicationsKan Qin
School of Marine Science and Technology, Northwestern Polytechnical University, Xi’an 710072, Shaanxi, China
4 shared publications- Kai Luo
Northwestern Polytechnical University School of Marine Science and Technology Xi’an, Shaanxi 710072 , China
2 shared publications - Kan Qin
School of Marine Science and Technology, Northwestern Polytechnical University, Xi’an 710072, China
2 shared publications Aihong Zou
1 shared publicationChuang Huang
1 shared publication
Latest Publications
- 4 October 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (11) , 1-79
Fluid–Thermal–Structural Analysis of Partial Admission Axial Impulse Turbines With Liquid Jet Impingement Cooling
Increasing turbine inlet temperature is beneficial to enhance turbine performance. However, this also results in stringent cooling requirements. Unlike turbines in air cycle machines, the partial admission axial impulse turbines for underwater vehicles can utilize the abundant seawater as the cooling medium. In addition, the short blades cannot accommodate the complex cooling channels used in aero-engines, and the alternative way is jet impingement liquid cooling. This paper proposes a fluid–thermal–structural coupling method to investigate the performance of partial admission axial impulse turbines with water-cooling on the rotating wheel front surface. The volume of fluid multiphase model is employed to study the transient gas–liquid interaction, while the Lee model is chosen to model the heat and mass transfer during phase change. Also, a two-way weakly coupling method among fluid, thermal, and structure is utilized to account for fluid–structure interaction. The results show that the temperature distribution at the turbine wheel drops significantly with the jet impingement liquid cooling. The turbine efficiency is also reduced by 3.38% due to the mixing of cooling medium and gas. From stress analysis, the use of water-cooling can minimize turbine damage and ensure stable turbine operation. This study provides insight into the cooling method for partial admission axial impulse turbines for the underwater vehicle.
- 4 October 2023
- Published by Wiley in Journal of Turbomachinery
- Vol. 145 (11) , 1-79
Fluid–Thermal–Structural Analysis of Partial Admission Axial Impulse Turbines With Liquid Jet Impingement Cooling
Increasing turbine inlet temperature is beneficial to enhance turbine performance. However, this also results in stringent cooling requirements. Unlike turbines in air cycle machines, the partial admission axial impulse turbines for underwater vehicles can utilize the abundant seawater as the cooling medium. In addition, the short blades cannot accommodate the complex cooling channels used in aero-engines, and the alternative way is jet impingement liquid cooling. This paper proposes a fluid–thermal–structural coupling method to investigate the performance of partial admission axial impulse turbines with water-cooling on the rotating wheel front surface. The volume of fluid multiphase model is employed to study the transient gas–liquid interaction, while the Lee model is chosen to model the heat and mass transfer during phase change. Also, a two-way weakly coupling method among fluid, thermal, and structure is utilized to account for fluid–structure interaction. The results show that the temperature distribution at the turbine wheel drops significantly with the jet impingement liquid cooling. The turbine efficiency is also reduced by 3.38% due to the mixing of cooling medium and gas. From stress analysis, the use of water-cooling can minimize turbine damage and ensure stable turbine operation. This study provides insight into the cooling method for partial admission axial impulse turbines for the underwater vehicle.
- Open Access
A Comparison of Partial Admission Axial and Radial Inflow Turbines for Underwater Vehicles
The metal fueled steam Rankine cycle has been successfully applied to Unmanned Underwater Vehicles. However, the suitable turbine configuration is yet to be determined for this particular application. In this paper, the mean-line design approach based on the existing empirical correlations is first described. The corresponding partial admission axial and radial inflow turbines are then preliminarily designed. To assess the performance of designed turbines, the three-dimensional Computational Fluid Dynamics (CFD) simulations and steady-state structural analysis are performed. The results show that axial turbines are more compact than radial inflow turbines at the same output power. In addition, since radial inflow turbines can reduce the exit energy loss, this benefit substantially offsets the increment of the rotor losses created by the low speed ratios and supersonic rotor inlet velocity. On the contrary, due to the large volume of dead gas and strong transient effects caused by the high rotor blade length of radial inflow turbines, the overall performance between axial and radial inflow turbines is comparable (within 4%). However, the strength of radial inflow turbines is slightly superior because of lower blade inlet height and outlet hub radius. This paper confirms that the axial turbine is the optimal configuration for underwater vehicles in terms of size, aerodynamics and structural performance.
Open AccessA Comparison of Partial Admission Axial and Radial Inflow Turbines for Underwater Vehicles
The metal fueled steam Rankine cycle has been successfully applied to Unmanned Underwater Vehicles. However, the suitable turbine configuration is yet to be determined for this particular application. In this paper, the mean-line design approach based on the existing empirical correlations is first described. The corresponding partial admission axial and radial inflow turbines are then preliminarily designed. To assess the performance of designed turbines, the three-dimensional Computational Fluid Dynamics (CFD) simulations and steady-state structural analysis are performed. The results show that axial turbines are more compact than radial inflow turbines at the same output power. In addition, since radial inflow turbines can reduce the exit energy loss, this benefit substantially offsets the increment of the rotor losses created by the low speed ratios and supersonic rotor inlet velocity. On the contrary, due to the large volume of dead gas and strong transient effects caused by the high rotor blade length of radial inflow turbines, the overall performance between axial and radial inflow turbines is comparable (within 4%). However, the strength of radial inflow turbines is slightly superior because of lower blade inlet height and outlet hub radius. This paper confirms that the axial turbine is the optimal configuration for underwater vehicles in terms of size, aerodynamics and structural performance.
- 1 November 2020
- Published by Elsevier in Energy Conversion and Management
- Vol. 223
Thermodynamic and experimental investigation of a metal fuelled steam Rankine cycle for Unmanned Underwater Vehicles
- 1 November 2020
- Published by Elsevier in Energy Conversion and Management
- Vol. 223
Thermodynamic and experimental investigation of a metal fuelled steam Rankine cycle for Unmanned Underwater Vehicles