Pavel Straka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Pavel Straka has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Olga Bičáková
Institute of Rock Structure and Mechanics, v.v.i., Czech Academy of Sciences, V Holešovičkách 94/41, 18209 Prague, Czech Republic
9 shared publications - Jaroslav Cihlář
Institute of Rock Structure and Mechanics, v.v.i., Czech Academy of Sciences, V Holešovičkách 94/41, 18209 Prague, Czech Republic
5 shared publications - Erik Meers
RE-SOURCE LAB, Laboratory for BioResource Recovery, Department of Green Chemistry and Technology, Faculty of Bioscience Engineering, Ghent University, Coupure Links 653, 9000 Ghent, Belgium
1 shared publication Ivana Sýkorová
Institute of Rock Structure and Mechanics, v.v.i, The Czech Academy of Sciences
1 shared publication- Jaroslav Cihlar
Institute of Rock Structure and Mechanics of the Czech Academy of Sciences
1 shared publication - Jaroslav Moško
Department of Power Engineering, Faculty of Environmental Technology, University of Chemistry and Technology, Prague, Technická 5, 166 28 Prague, Czech Republic
1 shared publication
Latest Publications
- Open Access
- 20 July 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (14) , 7241
Processing of Lignocellulosic Waste Biomass via Fine Cr2O3-Catalyzed Pyrolysis in a Sealed Pressure Reactor
The aim of the work is to present a technologically feasible method for processing waste biomass into synthesis gas for further use, namely for the synthesis of bio-methanol, which is considered an important renewable fuel. Walnut shells were tested as lignocellulosic waste. Samples with an operating particle size (0.5–3 mm) were pyrolyzed under well-defined conditions in a sealed pressure reactor, using chromium (III) oxide particles and fine particles as a catalyst. The effect of particle size on the yield and composition of resulting synthesis gas and biochar was tested. It was found that slow, catalyzed pressure pyrolysis at a final temperature of 400 °C provides synthesis gas with a H2/CO ratio of up to 0.9 or up to 1.8 and biochar (35–39 wt.%) useful as biofuel. These products were analyzed and their use described. The residual product was greywater (25–35 wt.%). Overall, under energy-saving conditions (slow pyrolysis, final temperature of 400 °C), pressure and catalyzed pyrolysis of biomass provide usable products and acceptable residuum.
- 20 July 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (14) , 7241
Open AccessProcessing of Lignocellulosic Waste Biomass via Fine Cr2O3-Catalyzed Pyrolysis in a Sealed Pressure Reactor
The aim of the work is to present a technologically feasible method for processing waste biomass into synthesis gas for further use, namely for the synthesis of bio-methanol, which is considered an important renewable fuel. Walnut shells were tested as lignocellulosic waste. Samples with an operating particle size (0.5–3 mm) were pyrolyzed under well-defined conditions in a sealed pressure reactor, using chromium (III) oxide particles and fine particles as a catalyst. The effect of particle size on the yield and composition of resulting synthesis gas and biochar was tested. It was found that slow, catalyzed pressure pyrolysis at a final temperature of 400 °C provides synthesis gas with a H2/CO ratio of up to 0.9 or up to 1.8 and biochar (35–39 wt.%) useful as biofuel. These products were analyzed and their use described. The residual product was greywater (25–35 wt.%). Overall, under energy-saving conditions (slow pyrolysis, final temperature of 400 °C), pressure and catalyzed pyrolysis of biomass provide usable products and acceptable residuum.
- 31 March 2026
- Published by University of Chemistry and Technology - Faculty of Environmental Technology in Paliva
Ru/Al2O3 catalyst-assisted processing of waste silane-grafted cross-linked polyethylene
Waste crosslinked polyethylene (XLPE) can be a source of valuable hydrocarbons for further use. XLPE is widely used material which – unlike polyethylene – is very stable both chemically and mechanically. There-fore, its waste is difficult to process. A very promising way is slow pyrolysis catalyzed by ruthenium (Ru/Al2O3) which allows the conversion of waste into hydrocarbons via degradation of rigid chemical structure of cross-linked material. High hydrocarbon yields (91–92 wt.%) were achieved by slow pyrolysis without or with cata-lyst, but significant changes in the composition of resulting gas and oil were found with the Ru/Al₂O₃ catalyst. To reveal the possibilities of using this catalyst for processing of XLPE at a relatively lower final temperature (max. 480 °C, mostly 450–470 °C), an effect of the catalyst on degradation of XLPE structure and related rheological properties of XLPE melt was investigated. It was found that the activation energy of degradation decreases significantly in the presence of the catalyst and the degradation is greatly facilitated by Ru/Al2O3 at the defect sites of the XLPE structure (the tertiary carbons). By the catalyst, the torque for XLPE melt and the its shear viscosity are significantly reduced already at 250 °C. Thus, Ru/Al2O3 catalyst, even in very small amounts (1 wt.% Ru), significantly promotes the degradation of XLPE structure and reduces the solid pyrolysis residue. This finding greatly facilitates the processing of waste XLPE. The catalytic mechanism of action of Ru is outlined and the equations for the XLPE cleavage are given. The main product of processing, pyrolysis oil, can be used as a clean heating fuel, or oil for further use, or a source of solvents, liquid and solid hydrocarbons, especially paraffin.
- 31 March 2026
- Published by University of Chemistry and Technology - Faculty of Environmental Technology in Paliva
Ru/Al2O3 catalyst-assisted processing of waste silane-grafted cross-linked polyethylene
Waste crosslinked polyethylene (XLPE) can be a source of valuable hydrocarbons for further use. XLPE is widely used material which – unlike polyethylene – is very stable both chemically and mechanically. There-fore, its waste is difficult to process. A very promising way is slow pyrolysis catalyzed by ruthenium (Ru/Al2O3) which allows the conversion of waste into hydrocarbons via degradation of rigid chemical structure of cross-linked material. High hydrocarbon yields (91–92 wt.%) were achieved by slow pyrolysis without or with cata-lyst, but significant changes in the composition of resulting gas and oil were found with the Ru/Al₂O₃ catalyst. To reveal the possibilities of using this catalyst for processing of XLPE at a relatively lower final temperature (max. 480 °C, mostly 450–470 °C), an effect of the catalyst on degradation of XLPE structure and related rheological properties of XLPE melt was investigated. It was found that the activation energy of degradation decreases significantly in the presence of the catalyst and the degradation is greatly facilitated by Ru/Al2O3 at the defect sites of the XLPE structure (the tertiary carbons). By the catalyst, the torque for XLPE melt and the its shear viscosity are significantly reduced already at 250 °C. Thus, Ru/Al2O3 catalyst, even in very small amounts (1 wt.% Ru), significantly promotes the degradation of XLPE structure and reduces the solid pyrolysis residue. This finding greatly facilitates the processing of waste XLPE. The catalytic mechanism of action of Ru is outlined and the equations for the XLPE cleavage are given. The main product of processing, pyrolysis oil, can be used as a clean heating fuel, or oil for further use, or a source of solvents, liquid and solid hydrocarbons, especially paraffin.
- Open Access
- 16 February 2026
- Published by Elsevier in Next Materials
- Vol. 11
Activation entropy of degradation of cross-linked polymer in catalyzed and uncatalyzed slow pyrolysis
- 16 February 2026
- Published by Elsevier in Next Materials
- Vol. 11
Open AccessActivation entropy of degradation of cross-linked polymer in catalyzed and uncatalyzed slow pyrolysis
- Open Access
- 29 December 2025
- Published by MDPI AG in Sustainability
- Vol. 18 (1) , 339
Fe2O3 Catalyst-Assisted Pyrolysis of Waste Cross-Linked Polyethylene on a Large Scale: Recycling of Difficult-to-Process Material
Cross-linked polyethylene (PEX) is very stable, both chemically and mechanically. This makes its waste difficult to process. A very promising approach is slow pyrolysis catalyzed by hematite (α-Fe2O3). Such pyrolysis was carried out on a large scale (feedstock of 38 kg, catalyst amount of 2 wt.%, heating rate of 4 K min−1, end temperature of 435 °C, delay at the end temperature several hours) and provided an oil containing both liquid (up to C17) and solid hydrocarbons (>C17). Thus, the oil obtained can be a source of valuable chemicals, solvents, and paraffin, and/or used as a clean liquid fuel and/or as a source of lubricants. Pyrolysis of PEX also yielded energy gas (12 wt.%) and solid carbonaceous residue (15 wt.%) for further use. The process mass balance and parameters (temperature, heating rate, dwell time, catalyst amount), composition, and chemical (elemental analysis, XRF, GC-MS, GC, distillation curve) and physical (viscosity, density, higher and lower heating value) properties of the oil, gas, and solid carbonaceous residue obtained are presented and discussed. The main product of the proposed technology is oil with a yield of almost 73 wt.%. The by-products are energy gas (12 wt.%) and solid carbonaceous residue (15 wt.%). The results obtained showed that the proposed technology successfully recycles difficult-to-process PEX with a process efficiency of 70%.
- 29 December 2025
- Published by MDPI AG in Sustainability
- Vol. 18 (1) , 339
Open AccessFe2O3 Catalyst-Assisted Pyrolysis of Waste Cross-Linked Polyethylene on a Large Scale: Recycling of Difficult-to-Process Material
Cross-linked polyethylene (PEX) is very stable, both chemically and mechanically. This makes its waste difficult to process. A very promising approach is slow pyrolysis catalyzed by hematite (α-Fe2O3). Such pyrolysis was carried out on a large scale (feedstock of 38 kg, catalyst amount of 2 wt.%, heating rate of 4 K min−1, end temperature of 435 °C, delay at the end temperature several hours) and provided an oil containing both liquid (up to C17) and solid hydrocarbons (>C17). Thus, the oil obtained can be a source of valuable chemicals, solvents, and paraffin, and/or used as a clean liquid fuel and/or as a source of lubricants. Pyrolysis of PEX also yielded energy gas (12 wt.%) and solid carbonaceous residue (15 wt.%) for further use. The process mass balance and parameters (temperature, heating rate, dwell time, catalyst amount), composition, and chemical (elemental analysis, XRF, GC-MS, GC, distillation curve) and physical (viscosity, density, higher and lower heating value) properties of the oil, gas, and solid carbonaceous residue obtained are presented and discussed. The main product of the proposed technology is oil with a yield of almost 73 wt.%. The by-products are energy gas (12 wt.%) and solid carbonaceous residue (15 wt.%). The results obtained showed that the proposed technology successfully recycles difficult-to-process PEX with a process efficiency of 70%.
- Open Access
Production of Syngas and Hydrogen-Rich Gas from Lignocellulosic Biomass via Ru/Al2O3 Catalyst-Assisted Slow Pyrolysis
The aim of this work is to present a technologically feasible method for processing biomass into synthesis gas or hydrogen-rich gas. Three types of biomass with different lignin contents were pyrolyzed in a pyrolysis unit under well-defined conditions (ambient pressure, heating rate of 10 K min−1, end temperature of 500 °C, operating particle size, variable catalyst mass) in the presence of a ruthenium catalyst (Ru/Al2O3, powder), and the effect of catalyst amount on the yield and gas composition was observed. Feedstock mass was always 50 g, and catalyst mass was 2.5, 5, and 10 g (mixing ratios 0.05, 0.1, and 0.2, resp.). During pyrolysis, the raw gas and vapors was passed through the catalyst bed and converted to the resulting gas and bio-oil. The gas obtained was cleaned by sequestration with CO2 using commercial active carbon to obtain syngas with different H2/CO ratios or hydrogen-rich gas. It was found that, depending on the catalyst amount, slow pyrolysis catalyzed by ruthenium yielded syngas with a H2/CO ratio of approximately 0.5–5, which is further usable. The by-products obtained (bio-oil and biochar) are also described. Bio-oils from all three biomass types contained mainly carboxylic acids (33–46 wt.%) and phenols (18–33 wt.%), hydroquinone (up to 5 wt.%), and a high amount of stearate (up to 26 wt.%). All of these compounds have high utility value. The resulting biochar can probably be applied, after activation using CO2, as a sorbent. In conclusion, under energy-efficient conditions (end temperature max. 500 °C), Ru/Al2O3-catalyzed pyrolysis of biomass provides syngas or hydrogen-rich gas and usable by-products. It should be emphasized that the maximum theoretical H2 production from biomass is 60–70 g H2/kg biomass. This limit value could negatively affect the technological development of the process.
Open AccessProduction of Syngas and Hydrogen-Rich Gas from Lignocellulosic Biomass via Ru/Al2O3 Catalyst-Assisted Slow Pyrolysis
The aim of this work is to present a technologically feasible method for processing biomass into synthesis gas or hydrogen-rich gas. Three types of biomass with different lignin contents were pyrolyzed in a pyrolysis unit under well-defined conditions (ambient pressure, heating rate of 10 K min−1, end temperature of 500 °C, operating particle size, variable catalyst mass) in the presence of a ruthenium catalyst (Ru/Al2O3, powder), and the effect of catalyst amount on the yield and gas composition was observed. Feedstock mass was always 50 g, and catalyst mass was 2.5, 5, and 10 g (mixing ratios 0.05, 0.1, and 0.2, resp.). During pyrolysis, the raw gas and vapors was passed through the catalyst bed and converted to the resulting gas and bio-oil. The gas obtained was cleaned by sequestration with CO2 using commercial active carbon to obtain syngas with different H2/CO ratios or hydrogen-rich gas. It was found that, depending on the catalyst amount, slow pyrolysis catalyzed by ruthenium yielded syngas with a H2/CO ratio of approximately 0.5–5, which is further usable. The by-products obtained (bio-oil and biochar) are also described. Bio-oils from all three biomass types contained mainly carboxylic acids (33–46 wt.%) and phenols (18–33 wt.%), hydroquinone (up to 5 wt.%), and a high amount of stearate (up to 26 wt.%). All of these compounds have high utility value. The resulting biochar can probably be applied, after activation using CO2, as a sorbent. In conclusion, under energy-efficient conditions (end temperature max. 500 °C), Ru/Al2O3-catalyzed pyrolysis of biomass provides syngas or hydrogen-rich gas and usable by-products. It should be emphasized that the maximum theoretical H2 production from biomass is 60–70 g H2/kg biomass. This limit value could negatively affect the technological development of the process.
- Open Access
Enhanced Recoverability and Recycling of Resistant Waste Crosslinked Polyethylene via FeTiO3 Catalyst-Assisted Slow Pyrolysis
Crosslinked polyethylene (XLPE) is a widely used material which—unlike polyethylene—is very stable both chemically and mechanically. Therefore, waste from this material is difficult to process. A very promising way is slow pyrolysis catalyzed by FeTiO3 (ilmenite), which allows the conversion of this waste into hydrocarbons via degradation of the rigid chemical structure of crosslinked material. High liquid hydrocarbon yields were achieved by slow pyrolysis both without and with a catalyst at a final temperature of 470 °C (65 and 75–76 wt.%, respectively), but with the catalyst significantly changing the composition of the resulting hydrocarbons. To reveal the possibilities of using the FeTiO3 catalyst for processing waste XLPE, the effect of this catalyst on the degradation of the XLPE structure was investigated. The degradation is probably greatly facilitated by the action of the FeTiO3 catalyst at the defect sites of the XLPE structure, i.e., at the tertiary carbons in the main chain where branching into cross-links occurs. In this way, the FeTiO3 catalyst, even in very small amounts (1%), significantly promotes the degradation of the XLPE structure. This leads to the formation of liquid hydrocarbons, up to 92 wt.% of the products obtained. The novelty of this work lies in a technologically feasible method for processing resistant crosslinked waste material using an inexpensive catalyst; the proposed method provides hydrocarbons with high utility value. On the whole, slow pyrolysis of XLPE waste catalyzed by FeTiO3 at a final temperature of 470 °C and carried out under well-defined conditions appears to be a promising method for converting this waste into valuable hydrocarbons and energy gas.
Open AccessEnhanced Recoverability and Recycling of Resistant Waste Crosslinked Polyethylene via FeTiO3 Catalyst-Assisted Slow Pyrolysis
Crosslinked polyethylene (XLPE) is a widely used material which—unlike polyethylene—is very stable both chemically and mechanically. Therefore, waste from this material is difficult to process. A very promising way is slow pyrolysis catalyzed by FeTiO3 (ilmenite), which allows the conversion of this waste into hydrocarbons via degradation of the rigid chemical structure of crosslinked material. High liquid hydrocarbon yields were achieved by slow pyrolysis both without and with a catalyst at a final temperature of 470 °C (65 and 75–76 wt.%, respectively), but with the catalyst significantly changing the composition of the resulting hydrocarbons. To reveal the possibilities of using the FeTiO3 catalyst for processing waste XLPE, the effect of this catalyst on the degradation of the XLPE structure was investigated. The degradation is probably greatly facilitated by the action of the FeTiO3 catalyst at the defect sites of the XLPE structure, i.e., at the tertiary carbons in the main chain where branching into cross-links occurs. In this way, the FeTiO3 catalyst, even in very small amounts (1%), significantly promotes the degradation of the XLPE structure. This leads to the formation of liquid hydrocarbons, up to 92 wt.% of the products obtained. The novelty of this work lies in a technologically feasible method for processing resistant crosslinked waste material using an inexpensive catalyst; the proposed method provides hydrocarbons with high utility value. On the whole, slow pyrolysis of XLPE waste catalyzed by FeTiO3 at a final temperature of 470 °C and carried out under well-defined conditions appears to be a promising method for converting this waste into valuable hydrocarbons and energy gas.
- Open Access
Conversion of Biomass to Energy-Rich Gas by Catalyzed Pyrolysis in a Sealed Pressure Reactor
The purpose of this work is to present a technologically feasible method for processing different types of biomass into energy-rich gas with a methane content higher than 60 vol.% or a hydrogen content higher than 65 vol.%. Selected biomass samples with different compositions were tested. Samples with an operational particle size were pyrolyzed under well-defined conditions in a sealed pressure reactor, and the influence of process parameters on the gas yield and composition was evaluated. Different metal catalysts were used. It was found that, depending on the catalyst used, slow catalyzed pressure pyrolysis at a final temperature of 400 °C yields a methane-rich gas with up to 70 vol.% CH4 or a hydrogen-rich gas with up to 75 vol.% H2. In addition, by-products (oil and biochar) were analyzed and their uses described. In conclusion, under energy-saving conditions, pressure-catalyzed pyrolysis of biomass provides energy-rich gas and other usable products.
Open AccessConversion of Biomass to Energy-Rich Gas by Catalyzed Pyrolysis in a Sealed Pressure Reactor
The purpose of this work is to present a technologically feasible method for processing different types of biomass into energy-rich gas with a methane content higher than 60 vol.% or a hydrogen content higher than 65 vol.%. Selected biomass samples with different compositions were tested. Samples with an operational particle size were pyrolyzed under well-defined conditions in a sealed pressure reactor, and the influence of process parameters on the gas yield and composition was evaluated. Different metal catalysts were used. It was found that, depending on the catalyst used, slow catalyzed pressure pyrolysis at a final temperature of 400 °C yields a methane-rich gas with up to 70 vol.% CH4 or a hydrogen-rich gas with up to 75 vol.% H2. In addition, by-products (oil and biochar) were analyzed and their uses described. In conclusion, under energy-saving conditions, pressure-catalyzed pyrolysis of biomass provides energy-rich gas and other usable products.
- Open Access
- 31 March 2023
- Published by University of Chemistry and Technology - Faculty of Environmental Technology in Paliva
- p. 19-23
Low-temperature treatment of waste crosslinked polyethylene with ruthenium catalyst
- 31 March 2023
- Published by University of Chemistry and Technology - Faculty of Environmental Technology in Paliva
- p. 19-23
Open AccessLow-temperature treatment of waste crosslinked polyethylene with ruthenium catalyst
- Open Access
A Comparison of the Efficiency of Catalysts Based on Ni, Ni-Co and Ni-Mo in Pressure Pyrolysis of Biomass Leading to Hythane
A thermal conversion of biomass to hythane using catalysts was studied. Low-temperature pyrolysis of two different types of biomass was performed in a pressure sealed reactor, and the resulting gas with high contents of CO2 and CO was methanized in a hydrogen atmosphere at a pressure of 30 bar. As catalysts, Ni/Al2O3, NiCo/Al2O3 and NiMo/Al2O3 were used and their catalytic activity was evaluated. The NiCo/Al2O3 catalyst showed the highest catalytic activity, Ni/Al2O3 had a lower but comparable one, and NiMo/Al2O3 showed the lowest activity. The resulting hythane contained 70 vol.% CH4 and 10 vol.% H2 (with NiCo/Al2O3 catalyst, HHV 29.20 MJ/m3, LHV 26.32 MJ/m3), or 57 vol.% CH4 and 23 vol% H2 (with Ni/Al2O3, HHV 25.92 MJ/m3, LHV 23.21 MJ/m3) or 47 vol.% CH4 and 27 vol.% H2 (with NiMo/Al2O3, HHV 23.23 MJ/m3, LHV 20.76 MJ/m3). It has been found that secondary reactions of volatile biomass products are of great importance for successful pressure pyrolysis.
Open AccessA Comparison of the Efficiency of Catalysts Based on Ni, Ni-Co and Ni-Mo in Pressure Pyrolysis of Biomass Leading to Hythane
A thermal conversion of biomass to hythane using catalysts was studied. Low-temperature pyrolysis of two different types of biomass was performed in a pressure sealed reactor, and the resulting gas with high contents of CO2 and CO was methanized in a hydrogen atmosphere at a pressure of 30 bar. As catalysts, Ni/Al2O3, NiCo/Al2O3 and NiMo/Al2O3 were used and their catalytic activity was evaluated. The NiCo/Al2O3 catalyst showed the highest catalytic activity, Ni/Al2O3 had a lower but comparable one, and NiMo/Al2O3 showed the lowest activity. The resulting hythane contained 70 vol.% CH4 and 10 vol.% H2 (with NiCo/Al2O3 catalyst, HHV 29.20 MJ/m3, LHV 26.32 MJ/m3), or 57 vol.% CH4 and 23 vol% H2 (with Ni/Al2O3, HHV 25.92 MJ/m3, LHV 23.21 MJ/m3) or 47 vol.% CH4 and 27 vol.% H2 (with NiMo/Al2O3, HHV 23.23 MJ/m3, LHV 20.76 MJ/m3). It has been found that secondary reactions of volatile biomass products are of great importance for successful pressure pyrolysis.