Yali Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yali Wang has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Chengjiu Zhu
Guangdong University of Technology
1 shared publication- Chengyun Wang
College of Mechanical and Electrical Engineering, Central South University, Changsha, Hunan 410083, China
1 shared publication - Ge Wang
Faculty of Mechanical and Electrical Engineering, Guangdong Polytechnic of Industry and Commerce, Guangzhou, China
1 shared publication Haidong Yang
1 shared publication- Haidong Yang
School of Economics and Management, Fuzhou University, Fuzhou, China
1 shared publication Jihua Zhu
Sunwoda Electronics Co., Ltd., Shenzhen 518107, China
1 shared publication
Latest Publications
- Open Access
- 8 May 2026
- Published by Association for Computing Machinery (ACM)
- p. 189-194
Meta-Mapping Based Automatic Process Definition for Flexible Service Orchestration in Customized Manufacturing
Traditional workflow systems suffer from low flexibility and manual process modeling in highly customized manufacturing, which cannot adapt to dynamic product demands and distributed manufacturing resources. To solve this problem, this paper proposes a meta-mapping based automatic process definition method, which upgrades the two-dimensional process information model to a three-dimensional business workflow model. The method maps the phase dimension to sequential flows and the granularity dimension to parallel nodes, realizing automatic generation of workflow definitions. Meanwhile, formal verification including reachability, safety and liveness is designed to ensure process validity. Experimental results show that the proposed method reduces the process modeling time by 27.45% for complex customized products, and significantly improves the flexibility of service orchestration.
- 8 May 2026
- Published by Association for Computing Machinery (ACM)
- p. 189-194
Open AccessMeta-Mapping Based Automatic Process Definition for Flexible Service Orchestration in Customized Manufacturing
Traditional workflow systems suffer from low flexibility and manual process modeling in highly customized manufacturing, which cannot adapt to dynamic product demands and distributed manufacturing resources. To solve this problem, this paper proposes a meta-mapping based automatic process definition method, which upgrades the two-dimensional process information model to a three-dimensional business workflow model. The method maps the phase dimension to sequential flows and the granularity dimension to parallel nodes, realizing automatic generation of workflow definitions. Meanwhile, formal verification including reachability, safety and liveness is designed to ensure process validity. Experimental results show that the proposed method reduces the process modeling time by 27.45% for complex customized products, and significantly improves the flexibility of service orchestration.
- Open Access
- 21 February 2025
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 20 (2) , e0315972
Thermodynamics, economy and environment analyses and optimization of series, parallel, dual-loop Kalina cycles for double-source heat recovery in cement industry
This research aims to investigate the heat recovery of both suspension preheater flue gas and clinker cooler hot air in cement industry. Three thermodynamic cycles including series Kalina Cycle (S-KC)、parallel Kalina Cycle (P-KC) and dual-loop Kalina Cycle (DL-KC) are introduced for converting dual-source heat resources into power to enhance the system efficiency for cement production process. Firstly, the multi-layer comprehensive evaluation models are established for the three thermodynamic cycles. Then, the parametric studies are implemented to estimate the influences of six key parameters on the system’s thermodynamic-economic-environmental performances. Meanwhile, optimization investigations consisting of thermodynamic optimal design (TOD), thermodynamic and economic optimal design (TEOD), and thermodynamic, economic and environmental optimal design (TEEOD) are considered, and the performances of systems and components are compared under three optimal design scenarios. The results prove that, for S-KC, P-KC and DL-KC, the higher net power output (Wnet) can be gained with decreasing condenser outlet temperature and regenerator temperature difference, and increasing evaporator temperature difference and superheat degree, the lower electricity production cost (EPC) can be acquired with decreasing condenser outlet temperature, evaporator temperature difference and regenerator temperature difference, while the less environment impact load (EIL) can be attained with decreasing condenser outlet temperature, regenerator temperature difference and basic ammonia concentration, and increasing superheat degree. In addition, under TOD, TEOD and TEEOD scenarios, DL-KC is the best selection from the thermodynamic, economic and environmental perspectives, with the corresponding Wnet of 7166 kW, 6904 kW and 6838 kW, the EPC of 0.00476 $/kWh, 0.00369 $/kWh and 0.00362$/kWh, the EIL of 0.0597 mPEChina,90/kWh, 0.0599 mPEChina,90/kW and 0.0593 mPEChina,90/kW. It also identifies that the evaporator unit is the key component contributing to exergy destruction and investment cost for three systems, while the pump has the maximum influence on environmental performance.
- 21 February 2025
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 20 (2) , e0315972
Open AccessThermodynamics, economy and environment analyses and optimization of series, parallel, dual-loop Kalina cycles for double-source heat recovery in cement industry
This research aims to investigate the heat recovery of both suspension preheater flue gas and clinker cooler hot air in cement industry. Three thermodynamic cycles including series Kalina Cycle (S-KC)、parallel Kalina Cycle (P-KC) and dual-loop Kalina Cycle (DL-KC) are introduced for converting dual-source heat resources into power to enhance the system efficiency for cement production process. Firstly, the multi-layer comprehensive evaluation models are established for the three thermodynamic cycles. Then, the parametric studies are implemented to estimate the influences of six key parameters on the system’s thermodynamic-economic-environmental performances. Meanwhile, optimization investigations consisting of thermodynamic optimal design (TOD), thermodynamic and economic optimal design (TEOD), and thermodynamic, economic and environmental optimal design (TEEOD) are considered, and the performances of systems and components are compared under three optimal design scenarios. The results prove that, for S-KC, P-KC and DL-KC, the higher net power output (Wnet) can be gained with decreasing condenser outlet temperature and regenerator temperature difference, and increasing evaporator temperature difference and superheat degree, the lower electricity production cost (EPC) can be acquired with decreasing condenser outlet temperature, evaporator temperature difference and regenerator temperature difference, while the less environment impact load (EIL) can be attained with decreasing condenser outlet temperature, regenerator temperature difference and basic ammonia concentration, and increasing superheat degree. In addition, under TOD, TEOD and TEEOD scenarios, DL-KC is the best selection from the thermodynamic, economic and environmental perspectives, with the corresponding Wnet of 7166 kW, 6904 kW and 6838 kW, the EPC of 0.00476 $/kWh, 0.00369 $/kWh and 0.00362$/kWh, the EIL of 0.0597 mPEChina,90/kWh, 0.0599 mPEChina,90/kW and 0.0593 mPEChina,90/kW. It also identifies that the evaporator unit is the key component contributing to exergy destruction and investment cost for three systems, while the pump has the maximum influence on environmental performance.
- 15 February 2022
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (2)
Multi-objective optimization and off-design performance based on thermodynamic -economic-environmental analysis of organic Rankine & Kalina cycles for roller kiln waste heat recovery
Heat recovery from roller kiln’s flue gas and cooling gas is interest topic to make ceramic tile production cleaner and more sustainable. Comparatively, the parallel double-evaporator regenerative organic Rankine cycle (PD-RORC) & Kalina cycle (PD-KC34 (Kalina cycle 34)) provide a good solution for a roller kiln’s low-temperature double heat sources utilization. In this research, the off-design performance of the multiobjective optimized PD-RORC & PD-KC34 based on thermodynamic-economic-environmental model is investigated to provide dependable assessment for the roller kiln’s waste heat recovery. Firstly, the multiobjective optimization of PD-RORC & PD-KC34 is carried out considering thermodynamic, economic and environmental factors, and TOPSIS method is used to select the optimal Pareto solution. Then, the influences of the roller kiln’s operating conditions and heat sink on the off-design performances of PD-RORC & PD-KC34 are further explored. The results show that, under the optimal condition, PD-RORC has superior exergy efficiency ( ) and environmental performance with of 49.76% and environment impact load ( ) of 0.096 mPEChina,90/kWh while PD-KC34 has better net power output ( ) and economic behavior with of 250.72 kW and electricity production cost ( ) of 0.090 $/kWh. In addition, excess air coefficient has the greatest impact on , , and for PD-RORC and PD-KC34. On the whole, PD-KC34 has higher sensitivity on and while PD-RORC shows greater sensitivity on and .- 15 February 2022
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (2)
Multi-objective optimization and off-design performance based on thermodynamic -economic-environmental analysis of organic Rankine & Kalina cycles for roller kiln waste heat recovery
Heat recovery from roller kiln’s flue gas and cooling gas is interest topic to make ceramic tile production cleaner and more sustainable. Comparatively, the parallel double-evaporator regenerative organic Rankine cycle (PD-RORC) & Kalina cycle (PD-KC34 (Kalina cycle 34)) provide a good solution for a roller kiln’s low-temperature double heat sources utilization. In this research, the off-design performance of the multiobjective optimized PD-RORC & PD-KC34 based on thermodynamic-economic-environmental model is investigated to provide dependable assessment for the roller kiln’s waste heat recovery. Firstly, the multiobjective optimization of PD-RORC & PD-KC34 is carried out considering thermodynamic, economic and environmental factors, and TOPSIS method is used to select the optimal Pareto solution. Then, the influences of the roller kiln’s operating conditions and heat sink on the off-design performances of PD-RORC & PD-KC34 are further explored. The results show that, under the optimal condition, PD-RORC has superior exergy efficiency ( ) and environmental performance with of 49.76% and environment impact load ( ) of 0.096 mPEChina,90/kWh while PD-KC34 has better net power output ( ) and economic behavior with of 250.72 kW and electricity production cost ( ) of 0.090 $/kWh. In addition, excess air coefficient has the greatest impact on , , and for PD-RORC and PD-KC34. On the whole, PD-KC34 has higher sensitivity on and while PD-RORC shows greater sensitivity on and .- 1 August 2021
- Published by Elsevier in Chinese Journal of Chemical Engineering
- Vol. 36, 181-189
Directional assist (0 1 0) plane growth in LiMnPO4 prepared by solvothermal method with polyols to enhance electrochemical performance
- 1 August 2021
- Published by Elsevier in Chinese Journal of Chemical Engineering
- Vol. 36, 181-189
Directional assist (0 1 0) plane growth in LiMnPO4 prepared by solvothermal method with polyols to enhance electrochemical performance