Jung-Woo Cho
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jung-Woo Cho has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
Chang-Heon Song
Advanced Mechatronics R&D Group, Korea Institute of Industrial Technology, Gyeongsan-si, Republic of Korea
5 shared publicationsMin-Gi Cho
Daegyeong Regional Division, Korea Institute of Industrial Technology, Daegu, South Korea
4 shared publications- Changheon Song
Advanced Mobility & Robot System Group, Korea Institute of Industrial Technology, Daegu 42994, Republic of Korea
3 shared publications - Daeji Kim
Advanced Mobility & Robot System Group, Korea Institute of Industrial Technology, Daegu 42994, Republic of Korea
3 shared publications Jin-Young Park
Daegyeong Regional Division, Korea Institute of Industrial Technology, Daegu, South Korea
3 shared publicationsJoo-Young Oh
Advanced Mechatronics R&D Group, Korea Institute of Industrial Technology, Gyeongsan-si, Republic of Korea
3 shared publications
Latest Publications
- Open Access
Physics Informed Structural Load Aware Work Path Planning for a Tilt-Rotator Excavator Using Multibody Dynamics and Dueling Deep Q-Learning: A Numerical Case Study
A tilt-rotator increases the reachable workspace of a hydraulic excavator, but its configuration also changes structural load paths. This study developed a structural-load-aware work-path planner for a 14-ton excavator using nominal analytical soil loads and an experimentally correlated multibody dynamics model. A full-factorial combination of five tilt angles, five rotation angles, and nine excavation positions yielded 225 candidate motions. The 147 retained motions had predicted peak stresses of 98.5–149.0 MPa. These stresses informed action features and reward penalties in an action-conditioned dueling deep Q-network. Excavated cells became non-traversable holes; the planner incorporated in-place turning and conditional posture-repeat constraints. In the 9 × 9 obstacle environment, the stress-informed agent’s selected route required 44 actions and 452 s of simulated time, compared with 47 actions and 458 s for its stress-uninformed counterpart; cumulative peak-stress indices were 3158.0 and 3361.8 MPa, respectively. In the 5 × 5 environment, its route required one additional action and had a 4.2% higher index. A 21 × 28 site-derived numerical environment was completed in 453 actions, including 280 excavations. The method supports comparative structural-load assessment for construction-machinery safety and future integration with machine-stability criteria. These single-seed comparisons neither establish statistical superiority nor validate machine stability.
Open AccessPhysics Informed Structural Load Aware Work Path Planning for a Tilt-Rotator Excavator Using Multibody Dynamics and Dueling Deep Q-Learning: A Numerical Case Study
A tilt-rotator increases the reachable workspace of a hydraulic excavator, but its configuration also changes structural load paths. This study developed a structural-load-aware work-path planner for a 14-ton excavator using nominal analytical soil loads and an experimentally correlated multibody dynamics model. A full-factorial combination of five tilt angles, five rotation angles, and nine excavation positions yielded 225 candidate motions. The 147 retained motions had predicted peak stresses of 98.5–149.0 MPa. These stresses informed action features and reward penalties in an action-conditioned dueling deep Q-network. Excavated cells became non-traversable holes; the planner incorporated in-place turning and conditional posture-repeat constraints. In the 9 × 9 obstacle environment, the stress-informed agent’s selected route required 44 actions and 452 s of simulated time, compared with 47 actions and 458 s for its stress-uninformed counterpart; cumulative peak-stress indices were 3158.0 and 3361.8 MPa, respectively. In the 5 × 5 environment, its route required one additional action and had a 4.2% higher index. A 21 × 28 site-derived numerical environment was completed in 453 actions, including 280 excavations. The method supports comparative structural-load assessment for construction-machinery safety and future integration with machine-stability criteria. These single-seed comparisons neither establish statistical superiority nor validate machine stability.
- Open Access
- 5 October 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (19) , 10990
Estimation of Impact Loads Transmitted to Vibro-Ripper Housing Using Transfer Path Analysis
This study aimed to estimate impact loads delivered to vibro-ripper housing through link modules, together with loads transmitted in various directions. Housing vibration resulting from impact loads generated during the operating condition and frequency response functions were assessed by vibration and modal experiments, respectively. Vibration data and transfer functions were applied in a transfer path analysis (TPA) model to analyze the quantified impact loads transmitted through the key components of the vibro-ripper to its housing. Impact loads derived by TPA for different housing parts were compared with those in the tooth derived from load-cell measurements, validating the TPA method. As a result of the verification, the impact load calculated by the TPA method was 193.7 kN, whereas that from the striking force measured by the load cell was 220 kN, a difference of 12.3%. The results of this study may be important input values for numerical analysis in equipment design and can be used as key data for structural safety evaluation and optimization. In summary, this paper introduces the vibration-based TPA method and considers its applicability to construction machinery exposed to impact vibration and loads.
- 5 October 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (19) , 10990
Open AccessEstimation of Impact Loads Transmitted to Vibro-Ripper Housing Using Transfer Path Analysis
This study aimed to estimate impact loads delivered to vibro-ripper housing through link modules, together with loads transmitted in various directions. Housing vibration resulting from impact loads generated during the operating condition and frequency response functions were assessed by vibration and modal experiments, respectively. Vibration data and transfer functions were applied in a transfer path analysis (TPA) model to analyze the quantified impact loads transmitted through the key components of the vibro-ripper to its housing. Impact loads derived by TPA for different housing parts were compared with those in the tooth derived from load-cell measurements, validating the TPA method. As a result of the verification, the impact load calculated by the TPA method was 193.7 kN, whereas that from the striking force measured by the load cell was 220 kN, a difference of 12.3%. The results of this study may be important input values for numerical analysis in equipment design and can be used as key data for structural safety evaluation and optimization. In summary, this paper introduces the vibration-based TPA method and considers its applicability to construction machinery exposed to impact vibration and loads.
- 19 September 2022
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 23 (10) , 1227
Correction: Durability Testing and Simulation Analysis of the Tension Spring Assembly of a 20-ton Excavator
- 19 September 2022
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 23 (10) , 1227
Correction: Durability Testing and Simulation Analysis of the Tension Spring Assembly of a 20-ton Excavator
- 26 July 2022
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 23 (8) , 869-879
Durability Testing and Simulation Analysis of the Tension Spring Assembly of a 20-ton Excavator
- 26 July 2022
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 23 (8) , 869-879
Durability Testing and Simulation Analysis of the Tension Spring Assembly of a 20-ton Excavator
- 21 May 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (7) , 1249-1270
Design of Pin-on-Disk Type Abrasion Testing Machine for Durability Assessment of Rock Cutting Tools
- 21 May 2021
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 22 (7) , 1249-1270
Design of Pin-on-Disk Type Abrasion Testing Machine for Durability Assessment of Rock Cutting Tools
- 1 December 2016
- Published by Taylor & Francis in Geosystem Engineering
- Vol. 20 (5) , 237-250
Computational fluid dynamics simulations to optimize the filling of an underground mine cavity with fly ash
Subsidence caused by the underground spaces of abandoned mines is a potential danger to life and property. This study focuses on optimizing the filling of these cavities at a site in Korea to prevent subsidence and to reuse abandoned mine. Fly ash produced from thermoelectric power plants might be profitably used to fill the abandoned workings. Computational fluid dynamics (CFD) is used here to simulate fly ash injection into mine cavities by a volume-of-fluid method. The numerical experiments are run after the establishment of three input parameters, which are used to optimize two output parameters. This series of CFD simulations investigates the effects of filling with respect to the operation factors of the filling method. The filling operation is then optimized with regard to efficiency and equipment cost. A low injection point with drilling connection of vertical shafts gives the most efficient filling of underground mine cavities.
- 1 December 2016
- Published by Taylor & Francis in Geosystem Engineering
- Vol. 20 (5) , 237-250
Computational fluid dynamics simulations to optimize the filling of an underground mine cavity with fly ash
Subsidence caused by the underground spaces of abandoned mines is a potential danger to life and property. This study focuses on optimizing the filling of these cavities at a site in Korea to prevent subsidence and to reuse abandoned mine. Fly ash produced from thermoelectric power plants might be profitably used to fill the abandoned workings. Computational fluid dynamics (CFD) is used here to simulate fly ash injection into mine cavities by a volume-of-fluid method. The numerical experiments are run after the establishment of three input parameters, which are used to optimize two output parameters. This series of CFD simulations investigates the effects of filling with respect to the operation factors of the filling method. The filling operation is then optimized with regard to efficiency and equipment cost. A low injection point with drilling connection of vertical shafts gives the most efficient filling of underground mine cavities.
- 8 September 2015
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 49 (4) , 1517-1532
Performance Assessment of Hard Rock TBM and Rock Boreability Using Punch Penetration Test
- 8 September 2015
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 49 (4) , 1517-1532
Performance Assessment of Hard Rock TBM and Rock Boreability Using Punch Penetration Test
- 24 June 2015
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 16 (7) , 1533-1542
Design study of a rock particle flushing device for a rock reaming machine by CFD simulation
- 24 June 2015
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 16 (7) , 1533-1542
Design study of a rock particle flushing device for a rock reaming machine by CFD simulation
- 24 June 2015
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 16 (7) , 1405-1414
Development of lab-scale rock drill apparatus for testing performance of a drill bit
- 24 June 2015
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 16 (7) , 1405-1414
Development of lab-scale rock drill apparatus for testing performance of a drill bit