INIgor' V. Nedoseko

Igor' V. Nedoseko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Igor' V. Nedoseko has a total of 83 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Performance of Concrete with Mechanochemically Activated Rice Husk Ash-Based Organomineral Modifiers

    by Akbota Arystanbek, Saken Uderbayev, Igor Nedoseko, Aizhan Baikunirova, Akmaral Zhapakhova, Nargul Saktaganova, Kanat Alenov

    This study evaluates a wet-activated multicomponent organomineral modifier for sustainable concrete. The modifier was produced by co-grinding Portland cement and rice husk ash (RHA) in the presence of Sika® ViscoCrete®-20HE and was subsequently combined with polypropylene fibers. Three modified mixtures were tested after 28 days of curing and compared with a control concrete. The modified concretes achieved compressive strengths of 42.2–45.0 MPa, compared with 36.8 MPa for the control. Among the tested formulations, Mix 2, containing 6 wt.% RHA, 4 wt.% polypropylene fibers, and 1.3 wt.% superplasticizer, showed the most favorable overall performance. Its compressive and flexural strengths reached 45.0 and 5.8 MPa, corresponding to observed differences of 22.3% and 26.1%, respectively, relative to the control formulation. Because the complete mixture compositions and w/c ratios differed, these comparisons do not isolate the contribution of any individual constituent. Fracture toughness increased from 1.15 to 2.16 MPa·m1/2, water absorption decreased from 6.8% to 5.1%, and freeze–thaw resistance increased from 138 to 242 cycles. Qualitative SEM and XRD observations showed morphological and phase-related differences between selected control and modified specimens; however, these observations did not establish the causes of the measured performance differences. In addition, because no compositionally identical non-activated RHA reference or direct reactivity test was included, the independent effect of wet activation on RHA reactivity could not be established. The investigated integrated modifier therefore shows potential for improving concrete performance while enabling the beneficial use of RHA.

  • Open Access

    Прогнозирование свойств грунтовых композитов на основе портландцемента

    by Дмитрий Михайлович Рябых, Игорь Вадимович Недосеко, Сергей Васильевич Клюев, Надежда Анатольевна Слободчикова

    При оценке качественных характеристик дорожно-строительных материалов широко используются различные модели и методы прогнозирования их свойств. В прогнозировании свойств материалов важную роль играют эмпирические зависимости различных качественных характеристик. В работе поставлена цель – выявить эмпирические зависимости морозостойкости от прочности, плотности и водостойкости модифицированных грунтовых композитов на основе портландцемента. По результатам выполненных исследований выявлены эмпирические зависимости прочности на сжатие после 25 циклов замораживания-оттаивания от прочности на сжатие и плотности и прочности на сжатие после 25 циклов замораживания-оттаивания от водостойкости в проектном возрасте и плотности. Построены уравнения регрессии и установлено, что прогнозирование работы модифицированных грунтовых композитов на основе портландцемента в различных сооружениях при воздействии замерзания и оттаивания должно осуществляться в первую очередь с учётом значений плотности и прочности на сжатие. Various models and methods for predicting their properties are widely used in assessing the qualitative characteristics of road construction materials. Empirical dependences of various qualitative characteristics play an important role in predicting the properties of materials. The aim of the work is to identify empirical dependences of frost resistance on the strength, density and water resistance of modified soil composites based on portland cement. Based on the results of the performed studies, empirical dependences of compressive strength after 25 freeze-thaw cycles on compressive strength and density and compressive strength after 25 freeze-thaw cycles on water resistance at the design age and density were revealed. Regression equations are constructed and it is established that forecasting the operation of modified soil composites based on Portland cement in various structures under the influence of freezing and thawing should be carried out primarily taking into account the values of density and compressive strength.

  • Dry Mixtures Strength and Elastic-Deformative Characteristics Determination for Construction 3D Gypsum and Cement Printing

    by D. A. Sinitsin, R. Kh. Mukhametrakhimov, A. A. Khafizov, G. Yu. Shagigalin, D. V. Kuznetsov, I. V. Nedoseko, Мухаметрахимов Р. Х.

    A new technique for dry mixtures strength and elastic-deformative characteristics determination for construction 3D gypsum, cement and mixed printing is described. It is shown that the standard testing methods of concretes and mortars used in construction practice for fine-grained concretes and mortars are inapplicable: firstly, due to the scale factor, and secondly, due to the significant voidness of the printed samples, which also varies widely. The developed technique is based on the method for determining the grouting mixtures characteristics on small cross-section samples. A new formwork mold consisting of several cylindrical links (in metal or polymer), allowing the samples molding and subsequent exposure directly during 3D printing, has been developed and tested in pilot industrial conditions. The samples made according to the proposed method were tested on a universal testing machine and their results made it possible to determine with sufficient reliability the dry mixes basic strength and elastic-deformative characteristics for construction 3D printing, such as compressive strength, prism strength, elasticity modulus, transverse deformation coefficient and to construct a full-scale stress–relative deformation curve.

  • Extra Light Foam Gypsum as a Promising Material for Frame Buildings Thermal Insulation

    by V. I. Magilat, O. A. Korol, R. I. Shigapov, R. S. Kildibaev, B. G. Bulatov, I. V. Nedoseko

    An overview and brief analysis of cellular concrete usage in modern construction is presented. It is noted that piece-by-piece wall products based on autoclaved aerated concrete, despite their cheapness and adaptability, do not cover the need for insulation of low-rise buildings, primarily in light steel and wooden frames. It is shown that cement-based non-autoclaved aerated concrete in most cases cannot be recommended for mass use due to its high shrinkage and the presence of plenty shrink cracks. The strength and thermal characteristics of extra light foam concrete, as well as its' sorptive water absorption at different relative humidity of ambient air are determined. The effectiveness of extra light gypsum foam usage in modern structural systems of low-rise buildings based on lightweight steel and wooden frames is substantiated.

  • Influence of carbon black additives and finely ground waste from stone wool production on characteristics of cement systems

    by S.V. Klyuev, N.A. Ayubov, E.V. Fomina, M.S. Ageeva, A.V. Klyuev, I.V. Nedoseko

    The object of research is cement composites with additives of carbon black and finely ground waste stone wool production. The work aims to design a mix of a cement composite with the additives of carbon black and finely ground waste from stone wool production, which achieves the best strength characteristics. The results show that carbon black is represented on average by particles of 155 microns with inclusions of large agglomerates up to 1-2 mm in size, consisting of almost homogeneous nanoparticles 10-20 nm in size. Carbon black is distinguished by high hydrophobic properties with a true powder density of 900 kg/m3 and a bulk density of 300 kg/m3. The chemical composition of black carbon is 70-80% carbon and 10-15% oxygen, and it also contains impurity compounds of zinc, iron, sulfur, silicon, and other elements. Carbon additives acquire hydrophilic properties in the presence of a plasticizer, and the degree of their influence on hydration becomes less pronounced. The contraction of the binder during the first three hours of hardening is reduced when carbon black is introduced into the cement system in an amount of 8%. A composition with the best strength characteristics was obtained: the content of finely ground waste from stone wool production is 6% by weight of the binder; carbon black content is 4-5%; W/C = 0.2. However, there is difficulty in mixing the mixture at such a low W/C. With a water-cement ratio of 0.3, this problem is solved, and the strength characteristics remain quite high.


  • Strengthening of monolithic concrete slabs against pushing

    by A.I. Bedov, A.I. Gabitov, G.N. Pervushin, L.F. Kazanskaya, I.V. Nedoseko

    Significant stress concentrations occur at the interface of floor slabs and columns in widely used monolithic reinforced concrete beamless frames. Therefore, the strength of the floor slabs must be checked for pushing under the loads from columns, bearing walls or stiffening diaphragms. The analysis of engineering solution of beamless monolithic reinforced concrete slabs of the administration nine-storey building with frame-walled load-bearing system is made. The strength thereof for pushing is found to be not provided under the given loads in a number of cases, due to this, experimental studies of strengthening the near-column areas of floor slabs have been carried out. When restoring the structures that suffered defects and damages in the course of their operation, composite materials having high tensile strength, low weight, constructibility and resistance to aggressive influence are widely used. The presented method for strengthening the near-column areas of floor slabs for ensuring their pushing strength with the use of chemical anchors has been developed, and a comparative analysis of the calculation results of the near-column areas of floor slabs with the adopted strengthening method with the results of experimental studies of slab fragments has been carried out. The operating conditions of the near-column areas of the floor slab have been simulated under the test method, and the results of the experimental samples testing are presented. All samples were found to have been destroyed by pushing through, with the destruction being of a plastic nature. The results of assessing the application of transverse reinforcement to the load-carrying capacity of the slab on pushing-through are presented. The results of experimental studies on assessing the pushing strength of extreme parts of monolithic floor slabs with columns reinforced with transverse glued-in reinforcement have shown good efficiency.

  • The effect of the temperature difference in the thickness of three-layer reinforced concrete enclosing structures in the operational stage on their stress-strain state

    by O.A. Korol, D.A. Sinitsin, I.V. Nedoseko, A.N. Pudovkin

    In three-layer reinforced concrete structures, the inner and outer layers of concrete of different physical and mechanical characteristics have different coefficients of thermal conductivity and linear temperature deformation. During the operation of buildings and structures, due to the temperature difference in the thickness of the structure along the contact planes of the layers, shear stresses may occur, which leads to bending of the structure, an increase in its deflections and a decrease in crack resistance. In this regard, when designing and calculating such structures, it is necessary to take into account the operational stresses and deflections caused by the temperature difference in the thickness of the enclosing structure. Taking into account the fact that the cross-section of three-layer enclosing structures with a monolithic connection of layers includes various types of concrete and reinforcement, differing in the values of the initial modulus of elasticity, to solve the problem, the cross-section of the enclosing structure is reduced to a homogeneous one corresponding to the largest initial modulus of elasticity of the concrete of the outer layers. Studies have been carried out to identify the effect of the thickness of the enclosing structure on the change in deflection, depending on the temperature difference, and its share in the total deflection of the structure. Despite the fact that the calculation results revealed a slight increase in the total deflection, taking into account the proportion of deflection that depends on the temperature difference, the study allows us to increase the accuracy of the calculation. The tendency to reduce the material consumption of structures and, consequently, a decrease in the thickness of the structure can lead to an increase in the proportion of deflection, depending on the temperature difference, which must be taken into account when choosing design solutions.


  • Investigation of structure and properties of expanded clay waste with the purpose of their use in the construction industry

    by D.A. Sinitsin, A.A. Yudin, A.A. Parfenova, A.F. Zanina, I.V. Nedoseko

    This paper describes the structure and properties of large-tonnage expanded clay gravel waste, which is generated as dust from the cyclone, or clay dust (when drying granules), and expanded clay dust from filters (when leaving the kiln, from the cooler and screen). The mineralogical and phase composition of expanded clay dust and its hydraulic activity were determined. Clay dust from cyclones corresponds to the specific surface of 2500 cm2/g, and expanded clay dust from filters - 6800 cm2/g, which allows us to recommend it for use as a fine mineral additive to cement mortars and concretes. Due to the fact that the bulk density of clay dust is about 1000 kg/m3, and expanded clay dust - 6300 kg/m3, it allows to recommend it in the form of facilitating raw material additives in the production of wall and partition products. The results of X-ray phase analysis of clay dust from cyclones showed the presence of significant residues of unburnt clay (more than 80%), and the analysis of expanded clay dust from filters showed the presence of solid high-temperature phases consisting of: Quartz (SiO2) – 50.28%, Albite C-1 (NaAlSi3O8) – 14.82%, Microcline maximum (KAlSi3O8) – 15.73%, Lime (CaO) – 2.77%, Calcite (CaCO3) – 5.11%, Alunogen (Al2(SO4)2(H2O)22) – 11.29%. Hydraulic activity of clay and expanded clay dust according to the methods of GOST R 56593 and GOST 30744 showed that it is extremely low, especially for clay dust (0.3 MPa). On the contrary, the characteristics of samples of clay-alkali compositions showed sufficient strength (for clay dust up to 6.8 MPa, and expanded clay dust up to 3.6 MPa), which allows them to be recommended as a component of slag-alkali binder for cement-soil bases of highways.


  • Dry mixes on gypsum and mixed bases in the construction of low-rise residential buildings using 3D printing technology

    by D.V. Kuznetsov, S.V. Klyuev, A.N. Ryazanov, D.A. Sinitsin, A.N. Pudovkin, E.V. Kobeleva, I.V. Nedoseko

    3D-printed building construction technology is developing in most countries, such as France, China, Russia and others, and the dry mixes and equipment used are being improved. The development of 3D-printing construction technology is dictated by its many advantages: architectural diversity, speed and automation of the technological process of construction of buildings and structures with a noticeable reduction in the cost of production. However, there are a number of problems of this technology that are waiting for optimal solutions. The paper proposes solutions to two such problems: firstly, the choice of mixture with gypsum and gypsum-cement binders, ensuring the continuity of the 3D printing process of the building and allowing the construction of buildings up to three floors with sufficient safety margin, high seismic stability, as well as with good heat and noise insulation; secondly, the design of buildings with a rational structural and technological solution of the roof and floor, allowing the interface of these structures with load-bearing printed walls. Different compositions of dry mixes were tested in a series of field tests of large-sized wall blocks made with the use of a construction 3D-printer and filled with especially light porous expanded claydite, expanded clay concrete or heat-insulating foam gypsum with subsequent testing on press equipment of increased load-carrying capacity (with determination of bearing capacity and deformability of the large-sized block). When designing low-rise buildings, erected by additive technology, as an optimal design of floors, it is proposed to use frame-monolithic beam structures made of metal thin-walled steel galvanized profiles, filled with foam gypsum mix, providing heat and noise insulation and covered with a thin layer of high-strength self-leveling gypsum mix, providing the necessary structural strength of the floor and, accordingly, the minimum load on the foundation.