Mohamed Ibrahim Hassan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohamed Ibrahim Hassan has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ali Emadi
Department of Electrical and Computer Engineering and McMaster Automotive Resource Centre (MARC), McMaster University, Hamilton, ON L8S 4L8, Canada
4 shared publications - Niloufar Keshmiri
McMaster Automotive Resource Centre (MARC), McMaster University, Hamilton, ON, Canada
3 shared publications - Mehdi Narimani
Department of Electrical and Computer Engineering, McMaster University, Hamilton, Canada
2 shared publications - Alan Dorneles Callegaro
McMaster Automotive Resource Centre, McMaster University, Hamilton, ON, Canada
1 shared publication Mario F. Cruz
Aerospace group Fluid and Electrical Distribution Division Eaton Corporation, Torrance, CA, USA
1 shared publication- Omar Zayed
High Power Electronics Laboratory (HiPEL), McMaster University, Hamilton, ON, Canada
1 shared publication
Latest Publications
- Open Access
- 24 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (4) , 9144-9162
A 15-kW Wide-Input Reconfigurable Three-Level DAB Converter for On-Board Charging of 1.25-kV Electric Vehicle Powertrains
The demand to reduce charging times and run-time losses in electric vehicles has created a push to increase battery pack’s voltage level. 800 V class vehicles in production are approaching the 1 kV voltage limit of the Combined Charging System (CCS) connector. New fast charging standards such as ChaoJi (CHAdeMO 3.0) and Megawatt Charging System (MCS) have voltages defined up to 1.5 kV and 1.25 kV, respectively. The SAE J3068 standard, focused on 3-Φ AC charging, recommends compatibility from 208/120Y to 600/347Y, resulting in a wide voltage variation of the power factor correction (PFC) stage’s DC link. This paper proposes a reconfiguration method of a neutral-point clamped (NPC) converter in a three-level dual active bridge (DAB) converter to accommodate the wide voltage swing. The reconfigurable three-level DAB converter (R3L-DAB) topology is introduced, and its modes of operation are presented. The steady-state analysis and its soft-switching criterion are discussed. A power loss model and design methodology are established to choose the switching frequency ( fsw ), turns ratio ( n ), and leakage inductance ( Lk ). Finally, the experimental results of a 15 kW R3L-DAB converter, with a power density of 3.25 kW/L and peak efficiency of 97.32% are presented.
- 24 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (4) , 9144-9162
Open AccessA 15-kW Wide-Input Reconfigurable Three-Level DAB Converter for On-Board Charging of 1.25-kV Electric Vehicle Powertrains
The demand to reduce charging times and run-time losses in electric vehicles has created a push to increase battery pack’s voltage level. 800 V class vehicles in production are approaching the 1 kV voltage limit of the Combined Charging System (CCS) connector. New fast charging standards such as ChaoJi (CHAdeMO 3.0) and Megawatt Charging System (MCS) have voltages defined up to 1.5 kV and 1.25 kV, respectively. The SAE J3068 standard, focused on 3-Φ AC charging, recommends compatibility from 208/120Y to 600/347Y, resulting in a wide voltage variation of the power factor correction (PFC) stage’s DC link. This paper proposes a reconfiguration method of a neutral-point clamped (NPC) converter in a three-level dual active bridge (DAB) converter to accommodate the wide voltage swing. The reconfigurable three-level DAB converter (R3L-DAB) topology is introduced, and its modes of operation are presented. The steady-state analysis and its soft-switching criterion are discussed. A power loss model and design methodology are established to choose the switching frequency ( fsw ), turns ratio ( n ), and leakage inductance ( Lk ). Finally, the experimental results of a 15 kW R3L-DAB converter, with a power density of 3.25 kW/L and peak efficiency of 97.32% are presented.
- Open Access
- 13 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 4, 330-342
Multi-Source Dual Active Bridge DC/DC Converter for More Electric Aircraft
The topology proposed in this paper aims for a multiple sources/loads integration to improve the power density of the electrical power distribution system (EPDS) of the more-electric aircraft (MEA) architecture. The different operating modes of the proposed topology add flexibility to the system enabling power flow between different sources, while controlling the power supplied to the low voltage (LV) network on the aircraft. Better system utilization is achieved as compared to conventional solutions. The system stability is improved considering that the multi-source DAB (MSDAB) topology can be configured to stabilize the high-voltage DC (HVDC) bus in case of voltage sag. A battery charging configuration utilizing the magnetizing inductance of the transformer is proposed and discussed as one of the operating modes of the converter. The power flow to the low-voltage bus network is controlled by phase shifting the gating signals between the two bridges. A design process using genetic algorithm (GA) optimization is introduced to optimally select the converter parameters to minimize the transformer RMS current. Simulation and experiments of the control schemes were performed to validate optimal operation of the proposed converter.
- 13 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 4, 330-342
Open AccessMulti-Source Dual Active Bridge DC/DC Converter for More Electric Aircraft
The topology proposed in this paper aims for a multiple sources/loads integration to improve the power density of the electrical power distribution system (EPDS) of the more-electric aircraft (MEA) architecture. The different operating modes of the proposed topology add flexibility to the system enabling power flow between different sources, while controlling the power supplied to the low voltage (LV) network on the aircraft. Better system utilization is achieved as compared to conventional solutions. The system stability is improved considering that the multi-source DAB (MSDAB) topology can be configured to stabilize the high-voltage DC (HVDC) bus in case of voltage sag. A battery charging configuration utilizing the magnetizing inductance of the transformer is proposed and discussed as one of the operating modes of the converter. The power flow to the low-voltage bus network is controlled by phase shifting the gating signals between the two bridges. A design process using genetic algorithm (GA) optimization is introduced to optimally select the converter parameters to minimize the transformer RMS current. Simulation and experiments of the control schemes were performed to validate optimal operation of the proposed converter.
- Open Access
- 2 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 2, 568-583
Design Optimization Methodology for Planar Transformers for More Electric Aircraft
Isolated DC-DC converters are considered the building blocks of modern aircraft electrical power networks. The high-frequency transformer utilized in such converters is the major contributor to the size and weight besides the thermal management system. In this paper, an optimization design methodology aims to minimize the transformer core size and improve the converter performance through optimized winding configurations. The transformer core selection is based on optimizing the maximum flux density while considering different magnetic materials and number of cores in parallel. The transformer core is selected for an interleaved winding configuration and to keep the windings current density below a certain limit. The trade-offs between the converter efficiency and core weight in selecting an optimum switching frequency are presented. Multi-layer minimum gradient (MLMG) winding configurations are proposed to eliminate the high-frequency oscillations (HFO) caused by the transformer parasitics. The proposed configurations resulted in a reduction of the intra-winding capacitance by 15 times with 20 $\%$ improvement in the transformer volume as compared to a similar conventional double-layers spiral configurations. Numerical simulations are performed in ANSYS Maxwell to validate the proposed design and the developed analytical models. The effect of the different configurations on the converter performance is verified in the PLECS simulation environment. PLECS simulation results are validated experimentally for the conventional and proposed configurations highlighting the improvements on the performance of the converter.
- 2 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 2, 568-583
Open AccessDesign Optimization Methodology for Planar Transformers for More Electric Aircraft
Isolated DC-DC converters are considered the building blocks of modern aircraft electrical power networks. The high-frequency transformer utilized in such converters is the major contributor to the size and weight besides the thermal management system. In this paper, an optimization design methodology aims to minimize the transformer core size and improve the converter performance through optimized winding configurations. The transformer core selection is based on optimizing the maximum flux density while considering different magnetic materials and number of cores in parallel. The transformer core is selected for an interleaved winding configuration and to keep the windings current density below a certain limit. The trade-offs between the converter efficiency and core weight in selecting an optimum switching frequency are presented. Multi-layer minimum gradient (MLMG) winding configurations are proposed to eliminate the high-frequency oscillations (HFO) caused by the transformer parasitics. The proposed configurations resulted in a reduction of the intra-winding capacitance by 15 times with 20 $\%$ improvement in the transformer volume as compared to a similar conventional double-layers spiral configurations. Numerical simulations are performed in ANSYS Maxwell to validate the proposed design and the developed analytical models. The effect of the different configurations on the converter performance is verified in the PLECS simulation environment. PLECS simulation results are validated experimentally for the conventional and proposed configurations highlighting the improvements on the performance of the converter.
- Open Access
- 9 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 2, 184-198
Comparison of Isolated Bidirectional DC/DC Converters Using WBG Devices for More Electric Aircraft
With the aim towards lighter and more efficient electrical systems in future aircraft, design of DC/DC converters with high efficiency, power density and improved thermal management becomes necessary. This paper investigates the detailed design of isolated bidirectional DC/DC converters for more electric aircraft (MEA). Use of wide bandgap (WBG) devices to enhance system efficiency is considered. A transformer optimization technique based on switching frequency for different converter topologies is investigated. The control strategy of the discussed configurations are verified in the PLECS simulation environment. Dual active bridge (DAB), input-series output-parallel (ISOP), neutral point clamped (NPC) and active neutral point clamped (ANPC) converters are considered to exploit benefits offered by WBG devices for MEA. A comparison is performed in terms of efficiency, thermal management, power density and electromagnetic interference (EMI). The results indicate that the ANPC converter is better for efficiency, thermal management and power density. The DAB converter showed similar results to the ISOP with the DAB yielding higher efficiency. The NPC and ANPC configurations resulted in the best EMI performance. The NPC converter proved to be the least effective solution with regard to efficiency, thermal management and power density.
- 9 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Industrial Electronics Society
- Vol. 2, 184-198
Open AccessComparison of Isolated Bidirectional DC/DC Converters Using WBG Devices for More Electric Aircraft
With the aim towards lighter and more efficient electrical systems in future aircraft, design of DC/DC converters with high efficiency, power density and improved thermal management becomes necessary. This paper investigates the detailed design of isolated bidirectional DC/DC converters for more electric aircraft (MEA). Use of wide bandgap (WBG) devices to enhance system efficiency is considered. A transformer optimization technique based on switching frequency for different converter topologies is investigated. The control strategy of the discussed configurations are verified in the PLECS simulation environment. Dual active bridge (DAB), input-series output-parallel (ISOP), neutral point clamped (NPC) and active neutral point clamped (ANPC) converters are considered to exploit benefits offered by WBG devices for MEA. A comparison is performed in terms of efficiency, thermal management, power density and electromagnetic interference (EMI). The results indicate that the ANPC converter is better for efficiency, thermal management and power density. The DAB converter showed similar results to the ISOP with the DAB yielding higher efficiency. The NPC and ANPC configurations resulted in the best EMI performance. The NPC converter proved to be the least effective solution with regard to efficiency, thermal management and power density.