Oleksandr Saichuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Oleksandr Saichuk has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Ivan Rybalko
Державний біотехнологічний університет
4 shared publications Andrii Zakharov
State Biotechnological University
3 shared publications- Olena Borovyk
Poltava State Agrarian University
3 shared publications - Андрій Вадимович Захаров
Державний біотехнологічний університет
3 shared publications - Nadiia Kolpachenko
Kharkiv Petro Vasylenko National Technical University of Agriculture
2 shared publications - Olekcii Potoskaev2 shared publications
Latest Publications
- Open Access
- 26 December 2025
- Published by Ukrainian State University of Railway Transport in Collection of scientific works of the Ukrainian State University of Railway Transport
- No. 214,p. 24-30
TECHNOLOGICAL ASPECTS OF REPAIRING WORN HOLES IN HOUSING PARTS OF AGRICULTURAL MACHINES USING NANOCOMPOSITE MATERIALS
Agricultural machinery components are frequently exposed to intensive cyclic loads, abrasive wear, and aggressive environmental factors, which cause accelerated deterioration of housing parts, particularly bearing and shaft seats. Traditional repair methods such as welding, surfacing, or installing bushings rely on high-temperature processes that often lead to structural deformation, residual stresses, or cracking of cast iron elements, and additionally require expensive equipment and significant labor costs. In contrast, the application of polymer nanocomposite materials provides a technological simple and energy-efficient alternative for the restoration of worn holes without thermal influence. Polymer matrices based on epoxy and polyurethane resins, modified with varies nanofillers such as graphene, carbon nanotubes, and nano-aluminum oxide, demonstrate improved mechanical properties, enhanced adhesion to metal nano-aluminum oxide, demonstrate improved mechanical properties, enhanced adhesion to metal surfaces, increased wear resistance, and high chemical stability during operation. The present study summarizes experiments investigations on the deformation-strength properties of selected nanocomposite, evaluates their tribological behavior under conditions typical for agricultural machinery operation, and proposes a practical restoration technology for worn housing holes. The methodology includes surface preparation, controlled application of the nanomodified polymer composition, and curing under optimized conditions. Comparative analysis with conventional repair approaches shows that the use of nanocomposites increases adhesion strength by up to 25 %, reduces the friction coefficient by 15-20 %, improver wear resistance by 28- 32 %, and decreases overall repair costs by 20-25 %. The developed technology is cost-effective, reliable, and suitable for implementation in repair workshops without the need for specialized hightemperature processing equipment, which confirms its practical relevance for extending the service life of agricultural machinery components.
- 26 December 2025
- Published by Ukrainian State University of Railway Transport in Collection of scientific works of the Ukrainian State University of Railway Transport
- No. 214,p. 24-30
Open AccessTECHNOLOGICAL ASPECTS OF REPAIRING WORN HOLES IN HOUSING PARTS OF AGRICULTURAL MACHINES USING NANOCOMPOSITE MATERIALS
Agricultural machinery components are frequently exposed to intensive cyclic loads, abrasive wear, and aggressive environmental factors, which cause accelerated deterioration of housing parts, particularly bearing and shaft seats. Traditional repair methods such as welding, surfacing, or installing bushings rely on high-temperature processes that often lead to structural deformation, residual stresses, or cracking of cast iron elements, and additionally require expensive equipment and significant labor costs. In contrast, the application of polymer nanocomposite materials provides a technological simple and energy-efficient alternative for the restoration of worn holes without thermal influence. Polymer matrices based on epoxy and polyurethane resins, modified with varies nanofillers such as graphene, carbon nanotubes, and nano-aluminum oxide, demonstrate improved mechanical properties, enhanced adhesion to metal nano-aluminum oxide, demonstrate improved mechanical properties, enhanced adhesion to metal surfaces, increased wear resistance, and high chemical stability during operation. The present study summarizes experiments investigations on the deformation-strength properties of selected nanocomposite, evaluates their tribological behavior under conditions typical for agricultural machinery operation, and proposes a practical restoration technology for worn housing holes. The methodology includes surface preparation, controlled application of the nanomodified polymer composition, and curing under optimized conditions. Comparative analysis with conventional repair approaches shows that the use of nanocomposites increases adhesion strength by up to 25 %, reduces the friction coefficient by 15-20 %, improver wear resistance by 28- 32 %, and decreases overall repair costs by 20-25 %. The developed technology is cost-effective, reliable, and suitable for implementation in repair workshops without the need for specialized hightemperature processing equipment, which confirms its practical relevance for extending the service life of agricultural machinery components.
- Open Access
- 30 October 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 5 (1(85)) , 30-35
Formation and properties of NbC-reinforced layers obtained by electroslag surfacing in a small-diameter current-fed crystallizer
The object of research is the process of forming NbC-reinforced composite layers by electroslag surfacing (ESS) in a small-diameter current-fed crystallizer (CFC). The problem being solved is the stable introduction of finely dispersed NbC into a small-diameter slag bath without dissolution and agglomeration, achieving uniform reinforcement, low porosity and high wear resistance. The research is aimed at experimentally determining the microstructure, phase composition, hardness, porosity, and abrasive wear resistance of layers formed under controlled ESS conditions using powder wire containing 35 wt.% NbC, and justifying the technological feasibility of the process in small-diameter CFC. The process was implemented in two-section CFC Ø 65–85 mm under the following conditions: I = 1.1 kA; U = 22 V; feed rate Vsupply = 2.0 m · min⁻¹; melting duration 45 s; Tbath = 1600–1700°C. Morphology and chemical homogeneity were determined by optical microscopy and SEM-EDS; phase composition – by X-ray diffraction; hardness – by Vickers HV10; abrasive wear resistance – according to ASTM G99. Layers of 2.0 ± 0.2 mm without macro-cracks and slag inclusions were obtained, with a uniform distribution of NbC (≈ 2–5 μm) throughout the thickness. The average hardness is 1020 ± 30 HV10 (≈ ×3 compared to steel 20), the linear wear rate is reduced by 3.4 times, porosity is ≤ 0.8 vol.% while maintaining high adhesive strength. It has been confirmed that the controlled feeding of non-current-carrying powder wire into the most heated zone of the bath ensures reproducible transfer of the refractory phase and prevents its dissolution and coarsening. The agreed microstructural features correlate with an increase in hardness and a decrease in wear, confirming the cause-and-effect relationship “structure → properties”. The proposed technology can be implemented on existing ESS installations without re-equipment and is recommended for the restoration of parts operating under conditions of abrasive wear, with the potential for scaling up by regulating modes and controlling slag composition.
- 30 October 2025
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 5 (1(85)) , 30-35
Open AccessFormation and properties of NbC-reinforced layers obtained by electroslag surfacing in a small-diameter current-fed crystallizer
The object of research is the process of forming NbC-reinforced composite layers by electroslag surfacing (ESS) in a small-diameter current-fed crystallizer (CFC). The problem being solved is the stable introduction of finely dispersed NbC into a small-diameter slag bath without dissolution and agglomeration, achieving uniform reinforcement, low porosity and high wear resistance. The research is aimed at experimentally determining the microstructure, phase composition, hardness, porosity, and abrasive wear resistance of layers formed under controlled ESS conditions using powder wire containing 35 wt.% NbC, and justifying the technological feasibility of the process in small-diameter CFC. The process was implemented in two-section CFC Ø 65–85 mm under the following conditions: I = 1.1 kA; U = 22 V; feed rate Vsupply = 2.0 m · min⁻¹; melting duration 45 s; Tbath = 1600–1700°C. Morphology and chemical homogeneity were determined by optical microscopy and SEM-EDS; phase composition – by X-ray diffraction; hardness – by Vickers HV10; abrasive wear resistance – according to ASTM G99. Layers of 2.0 ± 0.2 mm without macro-cracks and slag inclusions were obtained, with a uniform distribution of NbC (≈ 2–5 μm) throughout the thickness. The average hardness is 1020 ± 30 HV10 (≈ ×3 compared to steel 20), the linear wear rate is reduced by 3.4 times, porosity is ≤ 0.8 vol.% while maintaining high adhesive strength. It has been confirmed that the controlled feeding of non-current-carrying powder wire into the most heated zone of the bath ensures reproducible transfer of the refractory phase and prevents its dissolution and coarsening. The agreed microstructural features correlate with an increase in hardness and a decrease in wear, confirming the cause-and-effect relationship “structure → properties”. The proposed technology can be implemented on existing ESS installations without re-equipment and is recommended for the restoration of parts operating under conditions of abrasive wear, with the potential for scaling up by regulating modes and controlling slag composition.
- Open Access
- 31 December 2024
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 6 (1(80)) , 25-35
Development and improvement of roll casting technologies for universal beam mills
The object of this research is the casting technology of double-layer rolls for universal beam mills (UBM). They are critically important components of the metallurgical industry, ensuring the production of beams, profiles, and other structural elements, widely used in construction, mechanical engineering, transport, energy, and other industries. Developing innovative approaches to manufacturing rolls is strategically important for strengthening Ukraine's production potential. Since one of the most problematic areas is the dependence on imported rolls, which leads to significant economic losses, logistical risks and restrictions on the country's technological independence. Existing domestic technologies do not always lead to achieving the necessary operational characteristics, such as wear and heat resistance, and durability, complicating the competitiveness of products on the international market. The work proposes an innovative technology for manufacturing two-layer rolls, using stationary casting molds, a bainite-martensitic outer layer structure, and optimization of temperature conditions. This provides high hardness, heat resistance, and wear resistance of the outer layer. The inner layer, made of high-plasticity materials, compensates for residual stresses and improves structural stability. The use of alloying elements (nickel, molybdenum, copper) in combination with mathematical modelling of temperature fields made it possible to reduce the number of structural defects, such as porosity and delamination while ensuring uniform connection of the layers. This is because the proposed technology combines modern approaches to alloying, heat treatment optimization, and high-tech modelling of temperature conditions during casting. A notable characteristic is the optimization of materials to withstand elevated mechanical and thermal stresses, complemented by an advanced casting mold design that enhances interlayer adhesion and minimizes the likelihood of defects. This facilitates the reliable performance of rolls under challenging operational conditions, characterized by elevated mechanical and thermal stresses. Compared with similar known solutions, the proposed technology increases the service life of rolls by 20–25 %, reduces repair and maintenance costs by 15–20 %, and increases the efficiency of production processes by reducing the frequency of equipment shutdowns.
- 31 December 2024
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 6 (1(80)) , 25-35
Open AccessDevelopment and improvement of roll casting technologies for universal beam mills
The object of this research is the casting technology of double-layer rolls for universal beam mills (UBM). They are critically important components of the metallurgical industry, ensuring the production of beams, profiles, and other structural elements, widely used in construction, mechanical engineering, transport, energy, and other industries. Developing innovative approaches to manufacturing rolls is strategically important for strengthening Ukraine's production potential. Since one of the most problematic areas is the dependence on imported rolls, which leads to significant economic losses, logistical risks and restrictions on the country's technological independence. Existing domestic technologies do not always lead to achieving the necessary operational characteristics, such as wear and heat resistance, and durability, complicating the competitiveness of products on the international market. The work proposes an innovative technology for manufacturing two-layer rolls, using stationary casting molds, a bainite-martensitic outer layer structure, and optimization of temperature conditions. This provides high hardness, heat resistance, and wear resistance of the outer layer. The inner layer, made of high-plasticity materials, compensates for residual stresses and improves structural stability. The use of alloying elements (nickel, molybdenum, copper) in combination with mathematical modelling of temperature fields made it possible to reduce the number of structural defects, such as porosity and delamination while ensuring uniform connection of the layers. This is because the proposed technology combines modern approaches to alloying, heat treatment optimization, and high-tech modelling of temperature conditions during casting. A notable characteristic is the optimization of materials to withstand elevated mechanical and thermal stresses, complemented by an advanced casting mold design that enhances interlayer adhesion and minimizes the likelihood of defects. This facilitates the reliable performance of rolls under challenging operational conditions, characterized by elevated mechanical and thermal stresses. Compared with similar known solutions, the proposed technology increases the service life of rolls by 20–25 %, reduces repair and maintenance costs by 15–20 %, and increases the efficiency of production processes by reducing the frequency of equipment shutdowns.
- 1 January 2024
- Published by Publishing House Helvetica (Publications) in Transactions of Kremenchuk Mykhailo Ostrohradskyi National University
- Vol. 144 (1) , 190-195
FEATURES OF THE USE OF POLYMER COMPOSITE MATERIALS IN THE RESTORATION OF BEARING SEATS OF HOUSING PARTS
- 1 January 2024
- Published by Publishing House Helvetica (Publications) in Transactions of Kremenchuk Mykhailo Ostrohradskyi National University
- Vol. 144 (1) , 190-195
FEATURES OF THE USE OF POLYMER COMPOSITE MATERIALS IN THE RESTORATION OF BEARING SEATS OF HOUSING PARTS
- Open Access
- 1 February 2023
- Published by International Science Group in International Science Journal of Engineering & Agriculture
- Vol. 2 (1) , 1-9
Процес електрошлакового наплавлення з використанням електродних порошкових дротів
У даній роботі розглянуто технологію та техніку електрошлакової наплавки, а також приклади промислового застосування електрошлакової наплавки. Цей процес заснований на виділенні тепла електричного розряду у ванні розплавленого флюсу. Електрошлакова наплавка використовується для виготовлення біметалічних деталей, а також для отримання зносостійких покриттів. У процесі наплавлення електричний струм проходить через розплавлений зварювальний флюс, у результаті виділяється тепло, необхідне розплавлення кромок деталей і електрода. Електрод подається у ванну, що складається з рідкого флюсу, обмежену поверхнею, що розплавляється, і спеціальним формуючим пристроєм. Формуючим пристроєм можуть служити графітові, мідні або сталеві накладки. Флюси, що застосовуються, повинні мати певну в'язкість і електропровідність. При використанні флюсів з малою окислювальною здатністю мають місце незначні втрати легуючих елементів наплавлення. Електродами для наплавлення можуть бути зварювальні дроти, стрічки або стрижні великого перерізу. Температура внаслідок низької електро- та теплопровідності досягає більше 2000°С. Швидкість плавлення електрода дуже велика, коефіцієнт плавлення досягає 30 г/А ч., втрати на розбризкування практично відсутні.Кращі умови для наплавлення основного металу та отримання глибокої шлакової ванни створюються при вертикальному положенні шва, тому електрошлакове наплавлення найчастіше застосовують у поєднанні з примусовим формуванням зварювального шва. Наплавлення починають і закінчують з фіксацією деталі на спеціальних технологічних планках, які потім видаляють з деталі. На початку, поки процес ще не встановився, наплавлений шар може бути недостатньої якості, ця частина шва і залишається на початковій планці, в кінці шва планки застосовуються для виведення усадкової раковини.
- 1 February 2023
- Published by International Science Group in International Science Journal of Engineering & Agriculture
- Vol. 2 (1) , 1-9
Open AccessПроцес електрошлакового наплавлення з використанням електродних порошкових дротів
У даній роботі розглянуто технологію та техніку електрошлакової наплавки, а також приклади промислового застосування електрошлакової наплавки. Цей процес заснований на виділенні тепла електричного розряду у ванні розплавленого флюсу. Електрошлакова наплавка використовується для виготовлення біметалічних деталей, а також для отримання зносостійких покриттів. У процесі наплавлення електричний струм проходить через розплавлений зварювальний флюс, у результаті виділяється тепло, необхідне розплавлення кромок деталей і електрода. Електрод подається у ванну, що складається з рідкого флюсу, обмежену поверхнею, що розплавляється, і спеціальним формуючим пристроєм. Формуючим пристроєм можуть служити графітові, мідні або сталеві накладки. Флюси, що застосовуються, повинні мати певну в'язкість і електропровідність. При використанні флюсів з малою окислювальною здатністю мають місце незначні втрати легуючих елементів наплавлення. Електродами для наплавлення можуть бути зварювальні дроти, стрічки або стрижні великого перерізу. Температура внаслідок низької електро- та теплопровідності досягає більше 2000°С. Швидкість плавлення електрода дуже велика, коефіцієнт плавлення досягає 30 г/А ч., втрати на розбризкування практично відсутні.Кращі умови для наплавлення основного металу та отримання глибокої шлакової ванни створюються при вертикальному положенні шва, тому електрошлакове наплавлення найчастіше застосовують у поєднанні з примусовим формуванням зварювального шва. Наплавлення починають і закінчують з фіксацією деталі на спеціальних технологічних планках, які потім видаляють з деталі. На початку, поки процес ще не встановився, наплавлений шар може бути недостатньої якості, ця частина шва і залишається на початковій планці, в кінці шва планки застосовуються для виведення усадкової раковини.
- Open Access
- 10 December 2022
- Published by Publishing House Helvetica (Publications) in Bulletin of Sumy National Agrarian University. The series: Mechanization and Automation of Production Processes
- No. 2(48),p. 61-65
ЕЛЕКТРОШЛАКОВА НАПЛАВКА ПОВЕРХОНЬ ВИРОБІВ КОМПОЗИЦІЙНИМ ЗНОСОСТІЙКИМ СПЛАВОМ
Розроблено спосіб отримання зносостійких композиційних покриттів електрошлаковим наплавленням з використанням струмопідвідного кристалізатора і порошкових дротів, що містять тугоплавкі частинки дібориду титану TiB2. Вивчено термічні умови формування тонкого шару зносостійкого наплавленого металу та виявлено кінетику переходу в нього тугоплавких мікрочастинок із наповнювача порошкового дроту. Ванна рідкого шлаку, маючи меншу, ніж у розплавленого металу, густину, постійно перебуває над поверхнею металевого розплаву, захищаючи його від впливу повітря. Краплі присадного металу, проходячи через шлак, піддаються металургійній обробці і очищаються від шкідливих домішок. Напрямок конвекції шлаку залежить від діаметра електрода: при наплавленні тонким електродом переважає вимушена електромагнітна конвекція, шлак опускається біля електрода і піднімається по краях шлакової ванни, при використанні товстого електрода переважає вільна теплова конвекція, шлак опускається по краях шлакової ванни і піднімається поблизу електрода. Електроди можуть бути нерухомими, і їх розплавлення буде здійснюватись внаслідок постійного підняття шлакової і металевої ванн. Якщо ж електроди рухомі, то їх по мірі розплавлення безперервно подають у шлакову ванну. Можлива комбінація цих методів. Способи ЕШН можна класифікувати за різними ознаками, з яких технологічні є основними. У процесі ЕШН розрізняють два способи формування наплавленого металу. Один з них передбачає вільне формування розплаву зварювальної ванни на плоскій горизонтальній поверхні, а другий полягає у використанні спеціальних формувальних пристроїв – кристалізаторів, виготовлених переважно з міді. У них розплавлений метал кристалізується в замкнутій порожнині. Для запобігання перегріванню кристалізатори охолоджують проточною водою, а їх поверхні, що контактують з розплавами шлаку і металу, покривають графітом та іншими матеріалами, оберігаючи їх від електрохімічної ерозії. При ЕШН композитних покриттів в шлакову ванну сиплять зверху гранульований твердий сплав, температура плавлення якого вища за температуру плавлення металу-зв'язки, необхідність застосування якого обумовлена неприпустимістю вторинного розплавлення деяких твердих сплавів, через що наплавлення монопокрить з таких матеріалів неможлива. Твердість і зносостійкість забезпечується частинками твердого сплаву, а метал-зв'язка утримує їх на поверхні деталі.
- 10 December 2022
- Published by Publishing House Helvetica (Publications) in Bulletin of Sumy National Agrarian University. The series: Mechanization and Automation of Production Processes
- No. 2(48),p. 61-65
Open AccessЕЛЕКТРОШЛАКОВА НАПЛАВКА ПОВЕРХОНЬ ВИРОБІВ КОМПОЗИЦІЙНИМ ЗНОСОСТІЙКИМ СПЛАВОМ
Розроблено спосіб отримання зносостійких композиційних покриттів електрошлаковим наплавленням з використанням струмопідвідного кристалізатора і порошкових дротів, що містять тугоплавкі частинки дібориду титану TiB2. Вивчено термічні умови формування тонкого шару зносостійкого наплавленого металу та виявлено кінетику переходу в нього тугоплавких мікрочастинок із наповнювача порошкового дроту. Ванна рідкого шлаку, маючи меншу, ніж у розплавленого металу, густину, постійно перебуває над поверхнею металевого розплаву, захищаючи його від впливу повітря. Краплі присадного металу, проходячи через шлак, піддаються металургійній обробці і очищаються від шкідливих домішок. Напрямок конвекції шлаку залежить від діаметра електрода: при наплавленні тонким електродом переважає вимушена електромагнітна конвекція, шлак опускається біля електрода і піднімається по краях шлакової ванни, при використанні товстого електрода переважає вільна теплова конвекція, шлак опускається по краях шлакової ванни і піднімається поблизу електрода. Електроди можуть бути нерухомими, і їх розплавлення буде здійснюватись внаслідок постійного підняття шлакової і металевої ванн. Якщо ж електроди рухомі, то їх по мірі розплавлення безперервно подають у шлакову ванну. Можлива комбінація цих методів. Способи ЕШН можна класифікувати за різними ознаками, з яких технологічні є основними. У процесі ЕШН розрізняють два способи формування наплавленого металу. Один з них передбачає вільне формування розплаву зварювальної ванни на плоскій горизонтальній поверхні, а другий полягає у використанні спеціальних формувальних пристроїв – кристалізаторів, виготовлених переважно з міді. У них розплавлений метал кристалізується в замкнутій порожнині. Для запобігання перегріванню кристалізатори охолоджують проточною водою, а їх поверхні, що контактують з розплавами шлаку і металу, покривають графітом та іншими матеріалами, оберігаючи їх від електрохімічної ерозії. При ЕШН композитних покриттів в шлакову ванну сиплять зверху гранульований твердий сплав, температура плавлення якого вища за температуру плавлення металу-зв'язки, необхідність застосування якого обумовлена неприпустимістю вторинного розплавлення деяких твердих сплавів, через що наплавлення монопокрить з таких матеріалів неможлива. Твердість і зносостійкість забезпечується частинками твердого сплаву, а метал-зв'язка утримує їх на поверхні деталі.
- Open Access
- 1 December 2022
- Published by International Science Group in International Science Journal of Engineering & Agriculture
- Vol. 1 (5) , 70-76
Фізико-хімічні властивості флюсів та їхні технологічні параметри
Experimental and literary data on the properties and functions of fluxes and slags used for conducting stable remelting processes in various electroslag technologies are summarized. A formula for calculating the heat released during electroslag remelting (ESP) is proposed. The density and melting points of various fluxes were studied. The problem of obtaining high-quality metal with specified physical and mechanical properties and service characteristics is one of the main tasks in modern world metallurgical production, on which progress in many branches of industry directly depends. There are a number of technological processes for obtaining high-quality metal - vacuum-induction remelting, vacuum-arc remelting, electron-beam remelting, which have their own advantages and disadvantages and certain technical limitations. They do not solve the problem in general. The consumption of fluxes (slags) based on CaF2, Al2O3, MgO, CaO, MnO, SiO, NaF, etc. in metallurgical production is growing rapidly. This is due to the creation and introduction into production of new methods of smelting high-quality steels and alloys, which have special requirements for the physical and chemical properties of metallurgical fluxes. There are several general functions that slag performs in electroslag processes. This is primarily an energy-converting function. Slag is a section of an electrical circuit with high resistance, where electrical energy is converted into thermal energy. In addition, it performs a heat transfer function, which depends on the energy efficiency of the process. This efficiency is higher, the more fully and intensively the slag transfers the heat of the metal. Slag is an integral component of every process (EМS) of electroslag technologies, surfacing, casting, etc. The efficiency and productivity of processes depends on its properties, which are determined mainly by the chemical composition of the flux components used.
- 1 December 2022
- Published by International Science Group in International Science Journal of Engineering & Agriculture
- Vol. 1 (5) , 70-76
Open AccessФізико-хімічні властивості флюсів та їхні технологічні параметри
Experimental and literary data on the properties and functions of fluxes and slags used for conducting stable remelting processes in various electroslag technologies are summarized. A formula for calculating the heat released during electroslag remelting (ESP) is proposed. The density and melting points of various fluxes were studied. The problem of obtaining high-quality metal with specified physical and mechanical properties and service characteristics is one of the main tasks in modern world metallurgical production, on which progress in many branches of industry directly depends. There are a number of technological processes for obtaining high-quality metal - vacuum-induction remelting, vacuum-arc remelting, electron-beam remelting, which have their own advantages and disadvantages and certain technical limitations. They do not solve the problem in general. The consumption of fluxes (slags) based on CaF2, Al2O3, MgO, CaO, MnO, SiO, NaF, etc. in metallurgical production is growing rapidly. This is due to the creation and introduction into production of new methods of smelting high-quality steels and alloys, which have special requirements for the physical and chemical properties of metallurgical fluxes. There are several general functions that slag performs in electroslag processes. This is primarily an energy-converting function. Slag is a section of an electrical circuit with high resistance, where electrical energy is converted into thermal energy. In addition, it performs a heat transfer function, which depends on the energy efficiency of the process. This efficiency is higher, the more fully and intensively the slag transfers the heat of the metal. Slag is an integral component of every process (EМS) of electroslag technologies, surfacing, casting, etc. The efficiency and productivity of processes depends on its properties, which are determined mainly by the chemical composition of the flux components used.
- 31 December 2021
- Published by Poltava State Agrarian Academy in Вісник Полтавської державної аграрної академії
- No. 4,p. 259-267
ДОСЛІДЖЕННЯ ПРОЦЕСУ ПОДРІБНЮВАННЯ СТЕБЛОВОЇ МАСИ
У статті обґрунтовано та розкрито вирішення проблеми збереження гостроти ріжучих крайок ножів під час подрібнювання стеблової маси зернових культур. З’ясовано, що з урахуванням отриманого в роботі співвідношення, можна провести чисельні розрахунки впливу товщини шару стиснення на товщину ріжучої крайки ножа, якщо задати певну величину h і відомі властивості матеріалу, який ріжуть (τ, σ). Отримано вираз, що дозволяє проаналізувати залежність гостроти леза, з урахуванням конструктивних особливостей реальних ножів (радіуса заокруглення). Дані розрахунки залежать, як від висоти шару стиснення (при h=const), так і від висоти вихідного шару (при ), або від обох параметрів висоти шару при відомій залежності між ними. В дослідженні з’ясовано що, формула виведена В. П. Горячкіним, з міркувань мінімальних витрат енергії на різання, хоча й не враховує геометрію ріжучої крайки, все-таки дозволяє визначити оптимальний кут заточення ножа, якщо задати його товщину й ширину ріжучої крайки. Запропоновано графіки для розрахунків оптимальної товщини ріжучої крайки за умови n-кратного стиснення шару в момент розрізання. Отримані залежності для розрахунку впливу товщини подрібнюваної стеблової маси на товщину ріжучої крайки ножа, а також обґрунтований кут заточування ножа, який забезпечує мінімальне зусилля різання. Пропоновані розрахунки та рекомендації з обраної тематики дослідження доцільно застосовувати при використанні існуючих конструкцій та проектуванні нових елементів зернозбиральних комбайнів для подрібнення стеблової маси зернових культур. Результати проведеного дослідження доцільно впроваджувати в навчальний процес при підготовці здобувачів вищої освіти спеціальностей 208 Агроінженерія та 133 Галузеве машинобудування.
- 31 December 2021
- Published by Poltava State Agrarian Academy in Вісник Полтавської державної аграрної академії
- No. 4,p. 259-267
ДОСЛІДЖЕННЯ ПРОЦЕСУ ПОДРІБНЮВАННЯ СТЕБЛОВОЇ МАСИ
У статті обґрунтовано та розкрито вирішення проблеми збереження гостроти ріжучих крайок ножів під час подрібнювання стеблової маси зернових культур. З’ясовано, що з урахуванням отриманого в роботі співвідношення, можна провести чисельні розрахунки впливу товщини шару стиснення на товщину ріжучої крайки ножа, якщо задати певну величину h і відомі властивості матеріалу, який ріжуть (τ, σ). Отримано вираз, що дозволяє проаналізувати залежність гостроти леза, з урахуванням конструктивних особливостей реальних ножів (радіуса заокруглення). Дані розрахунки залежать, як від висоти шару стиснення (при h=const), так і від висоти вихідного шару (при ), або від обох параметрів висоти шару при відомій залежності між ними. В дослідженні з’ясовано що, формула виведена В. П. Горячкіним, з міркувань мінімальних витрат енергії на різання, хоча й не враховує геометрію ріжучої крайки, все-таки дозволяє визначити оптимальний кут заточення ножа, якщо задати його товщину й ширину ріжучої крайки. Запропоновано графіки для розрахунків оптимальної товщини ріжучої крайки за умови n-кратного стиснення шару в момент розрізання. Отримані залежності для розрахунку впливу товщини подрібнюваної стеблової маси на товщину ріжучої крайки ножа, а також обґрунтований кут заточування ножа, який забезпечує мінімальне зусилля різання. Пропоновані розрахунки та рекомендації з обраної тематики дослідження доцільно застосовувати при використанні існуючих конструкцій та проектуванні нових елементів зернозбиральних комбайнів для подрібнення стеблової маси зернових культур. Результати проведеного дослідження доцільно впроваджувати в навчальний процес при підготовці здобувачів вищої освіти спеціальностей 208 Агроінженерія та 133 Галузеве машинобудування.
- 13 March 2021
- Published by Springer Nature
- p. 617-628
Determining the Stresses in Beams Due to Short-Term Effect on Their Supports
- 13 March 2021
- Published by Springer Nature
- p. 617-628
Determining the Stresses in Beams Due to Short-Term Effect on Their Supports