D. S. Gromyka
D. S. Gromyka has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Dmitriy O. Nagornov
St. Petersburg Mining University, 2, 21-line VO, St. Petersburg, 199106, Russia
2 shared publications - Eldar Abdollovich Kremcheyev
St. Petersburg Mining University, 2, 21-line VO, St. Petersburg, 199106, Russia
2 shared publications A. I. Shikhov
1 shared publicationA. M. Shmakov
1 shared publicationA. S. Umansky
1 shared publicationD. R. Shakirzyanova
1 shared publication
Latest Publications
- 1 January 2026
- Published by International Digital Organization for Scientific Information (IDOSI) in International Journal of Engineering
- Vol. 39 (10) , 2500-2508
Improving the Accuracy of Hardness Measurement using UCI Transducers for Inspecting the Heat-Affected Zone of Welded Joints in Steel Pipelines
- 1 January 2026
- Published by International Digital Organization for Scientific Information (IDOSI) in International Journal of Engineering
- Vol. 39 (10) , 2500-2508
Improving the Accuracy of Hardness Measurement using UCI Transducers for Inspecting the Heat-Affected Zone of Welded Joints in Steel Pipelines
- Open Access
- 1 January 2026
- Published by International Digital Organization for Scientific Information (IDOSI) in International Journal of Engineering
- Vol. 39 (1) , 104-111
Possibility Evaluation of Monitoring Areas of Local Plastic Deformation During Fatigue Wear of Metal Structures Using the Dynamic Instrumented Indentation Method
Due to cyclic loading of mining machines, such as excavators, stress accumulates in the metal structures of the excavator's operating equipment, such as bucket, arm, and boom. Maximum stress areas occur in similar regions of the operating equipment in different excavators. Critical accumulation of damage can lead to the formation of fatigue cracks, significantly increasing the risk of accidents. For in-time prevention of accidents, constant monitoring of the operating equipment's condition is necessary, which can be achieved by controlling the mechanical properties of local plastic deformation areas using the dynamic Instrumented indentation method directly at the machine's operating site. This study analyzed changes in the mechanical properties of steel samples at different degrees of deformation using the dynamic Instrumented indentation method, as well as other methods for monitoring physical and mechanical properties to compare measurement results. The results showed that as the sample deforms, hardness increases and the elastic modulus decreases, which can be accurately assessed by dynamic Instrumented indentation method, which confirms the possibility of monitoring the degree of fatigue wear in metal structures using portable devices implementing this method.
- 1 January 2026
- Published by International Digital Organization for Scientific Information (IDOSI) in International Journal of Engineering
- Vol. 39 (1) , 104-111
Open AccessPossibility Evaluation of Monitoring Areas of Local Plastic Deformation During Fatigue Wear of Metal Structures Using the Dynamic Instrumented Indentation Method
Due to cyclic loading of mining machines, such as excavators, stress accumulates in the metal structures of the excavator's operating equipment, such as bucket, arm, and boom. Maximum stress areas occur in similar regions of the operating equipment in different excavators. Critical accumulation of damage can lead to the formation of fatigue cracks, significantly increasing the risk of accidents. For in-time prevention of accidents, constant monitoring of the operating equipment's condition is necessary, which can be achieved by controlling the mechanical properties of local plastic deformation areas using the dynamic Instrumented indentation method directly at the machine's operating site. This study analyzed changes in the mechanical properties of steel samples at different degrees of deformation using the dynamic Instrumented indentation method, as well as other methods for monitoring physical and mechanical properties to compare measurement results. The results showed that as the sample deforms, hardness increases and the elastic modulus decreases, which can be accurately assessed by dynamic Instrumented indentation method, which confirms the possibility of monitoring the degree of fatigue wear in metal structures using portable devices implementing this method.
- 1 January 2021
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 2
Estimation methods of wear mechanisms in cutting heads of mining machines: Review
Добыча полезных ископаемых повсеместно сопряжена с использованием разнообразных горных машин для выемки, погрузки и транспортирования породы. При длительном использовании техники увеличивается износ основных узлов и исполнительных органов машины. Данная проблема особенно актуальна для выемочно-погрузочных машин, используемых на работах по добыче полезных ископаемых и рекультивации, где наблюдается повышенная интенсивность изнашивания. Вопросы развития процессов изнашивания и оценки остаточного ресурса исполнительных органов выемочно-погрузочных машин хорошо изучен в мировой практике, однако по причине разнообразия климатических, геологических и горнотехнических условий, комплекс которых уникален для каждого месторождения полезных ископаемых, существуют сложности в создании единой модели развития данного процесса. В особенности малоизучен вопрос оценки остаточного ресурса при активном изнашивании в экстремальных условиях высоких температур, а также резком перепаде температуры рабочих органов. Данные условия характерны для угольных и торфяных месторождений, на которых характерно возникновение и развитие процессов эндогенного горения добываемого сырья. В данном обзорном исследовании рассмотрены методы оценки различных механизмов изнашивания и влияние температуры на интенсивность этого процесса, а также возможность определения остаточного ресурса исполнительных органов выемочно-погрузочных машин, работающих в условиях высокотемпературного горного...
- 1 January 2021
- Published by LLC Gornaya Kniga in Mining informational and analytical bulletin
- No. 2
Estimation methods of wear mechanisms in cutting heads of mining machines: Review
Добыча полезных ископаемых повсеместно сопряжена с использованием разнообразных горных машин для выемки, погрузки и транспортирования породы. При длительном использовании техники увеличивается износ основных узлов и исполнительных органов машины. Данная проблема особенно актуальна для выемочно-погрузочных машин, используемых на работах по добыче полезных ископаемых и рекультивации, где наблюдается повышенная интенсивность изнашивания. Вопросы развития процессов изнашивания и оценки остаточного ресурса исполнительных органов выемочно-погрузочных машин хорошо изучен в мировой практике, однако по причине разнообразия климатических, геологических и горнотехнических условий, комплекс которых уникален для каждого месторождения полезных ископаемых, существуют сложности в создании единой модели развития данного процесса. В особенности малоизучен вопрос оценки остаточного ресурса при активном изнашивании в экстремальных условиях высоких температур, а также резком перепаде температуры рабочих органов. Данные условия характерны для угольных и торфяных месторождений, на которых характерно возникновение и развитие процессов эндогенного горения добываемого сырья. В данном обзорном исследовании рассмотрены методы оценки различных механизмов изнашивания и влияние температуры на интенсивность этого процесса, а также возможность определения остаточного ресурса исполнительных органов выемочно-погрузочных машин, работающих в условиях высокотемпературного горного...
- Open Access
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1384 (1) , 012016
Review of applicability of using indicator gas coefficients for determining the temperature of the place of spontaneous combustion of coal
Spontaneous combustion of coal beds is considered to be one of the most hazardous effects of coal mining. The most dangerous factor of this process is its abruptness due to several types of coal possible emergence of reaction at low-temperature conditions and subtle reaction behavior at initial stage of the process, which may turn into environmental disaster. Therefore, on many mines and strip mines, in terms of occupation health and safety program and fire- preventing measures realization, fire monitoring system are introduced, as well as spontaneous combustion source monitoring system to apply fire-preventing measures. The most effective type of monitoring systems is gas monitoring, at which cause in many countries, including Russia, spontaneous combustion source indication methods based on fire gases concentration measurement are developed. Those methods are based on sharp increase of some specific gases, such as carbon monoxide and methane, at some point of spontaneous combustion source temperature, which differs depending on coal type and coal deposit. However, the application of those methods does not always allow the advance detection of coal spontaneous combustion areas, due to its low accuracy and dependence of fire-indication gases from external exposure. For that reason, many authors are advising ratios of fire gases or indicator gases ratios as a means of higher-precise spontaneous combustion sources indication method. In this paper, the analysis of those ratios applicability is conducted as well as existing underground fires indication methods.
- 1 November 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1384 (1) , 012016
Open AccessReview of applicability of using indicator gas coefficients for determining the temperature of the place of spontaneous combustion of coal
Spontaneous combustion of coal beds is considered to be one of the most hazardous effects of coal mining. The most dangerous factor of this process is its abruptness due to several types of coal possible emergence of reaction at low-temperature conditions and subtle reaction behavior at initial stage of the process, which may turn into environmental disaster. Therefore, on many mines and strip mines, in terms of occupation health and safety program and fire- preventing measures realization, fire monitoring system are introduced, as well as spontaneous combustion source monitoring system to apply fire-preventing measures. The most effective type of monitoring systems is gas monitoring, at which cause in many countries, including Russia, spontaneous combustion source indication methods based on fire gases concentration measurement are developed. Those methods are based on sharp increase of some specific gases, such as carbon monoxide and methane, at some point of spontaneous combustion source temperature, which differs depending on coal type and coal deposit. However, the application of those methods does not always allow the advance detection of coal spontaneous combustion areas, due to its low accuracy and dependence of fire-indication gases from external exposure. For that reason, many authors are advising ratios of fire gases or indicator gases ratios as a means of higher-precise spontaneous combustion sources indication method. In this paper, the analysis of those ratios applicability is conducted as well as existing underground fires indication methods.
- Open Access
- 10 December 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1118 (1) , 012021
Techniques to determine spontaneous ignition of brown coal
Open-pit mining of mineral deposits is characterised by a significant level of adverse effects on the atmospheric air due to both natural and technogenic phenomena. When assessing the environmental impact, some authors often do not take into account the phenomenon of endogenous spontaneous coal combustion, which can lead to the release of various toxic substances into the atmosphere. In cases of an imperfect control system, and untimely adoption of fire prevention measures, spontaneous combustion can cause catastrophic consequences. This issue is particularly acute in decommissioned facilities, where uncontrolled temperature growth occurs in a fire seat, the area of which increases daily in the absence of monitoring of combustion in strata and dumps. Such circumstances are observed at the Korkino Coal Mine, where seats of endogenous brown coal combustion have been observed for over 25 years. Since the mine is decommissioned, its reclamation is necessary with the development of complex works on the isolation of endogenous burning seats. Carrying out these works at the modern level requires the creation of a mathematical model of the process, providing a comprehensive study of the main parameters of spontaneous combustion, and also estimates of release intensity of the main fire gases at different temperatures. This paper presents the results of an analysis of the experience of conducting experimental studies of the processes of spontaneous combustion of brown coal, which served as the basis for building an experimental facility for studying the processes of spontaneous combustion and endogenous combustion of brown coals of the Korkino Coal Mine.
- 10 December 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1118 (1) , 012021
Open AccessTechniques to determine spontaneous ignition of brown coal
Open-pit mining of mineral deposits is characterised by a significant level of adverse effects on the atmospheric air due to both natural and technogenic phenomena. When assessing the environmental impact, some authors often do not take into account the phenomenon of endogenous spontaneous coal combustion, which can lead to the release of various toxic substances into the atmosphere. In cases of an imperfect control system, and untimely adoption of fire prevention measures, spontaneous combustion can cause catastrophic consequences. This issue is particularly acute in decommissioned facilities, where uncontrolled temperature growth occurs in a fire seat, the area of which increases daily in the absence of monitoring of combustion in strata and dumps. Such circumstances are observed at the Korkino Coal Mine, where seats of endogenous brown coal combustion have been observed for over 25 years. Since the mine is decommissioned, its reclamation is necessary with the development of complex works on the isolation of endogenous burning seats. Carrying out these works at the modern level requires the creation of a mathematical model of the process, providing a comprehensive study of the main parameters of spontaneous combustion, and also estimates of release intensity of the main fire gases at different temperatures. This paper presents the results of an analysis of the experience of conducting experimental studies of the processes of spontaneous combustion of brown coal, which served as the basis for building an experimental facility for studying the processes of spontaneous combustion and endogenous combustion of brown coals of the Korkino Coal Mine.