Adriana Enache

Ice accretion poses substantial safety hazards for the manned and unmanned aviation industries. Its study is essential for icing events risk assessment and for the development of efficient ice protection systems. The existing ice accretion measurement techniques—casting, molding, and laser-scanning—are time-consuming, sometimes cumbersome to use, and highly expensive, while hand tracing is inexpensive, but has lower accuracy and time-consuming post-processing. This work presents two low-cost, fast, and easy-to-use measurement techniques for 2D ice accretion profiles. Both employ algorithms of automatic ice shape detection, one based on unmediated image-processing, another based on the processing of manual ice tracings. The techniques are applied to ice accretion experiments conducted in an icing wind tunnel at low Reynolds numbers, and their results are validated against ice thickness caliper measurements. A comparison of the results shows that both techniques accurately measure the leading-edge ice thickness and the 2D shape of the ice accretion profiles. One technique is faster, with higher measurement accuracy, but produces interrupted-line 2D ice profiles and requires good lighting conditions, while the other generates continuous-line 2D profiles and has no application restriction, but it is slower, with lower accuracy. A discussion is conducted, aiming to help one determine the best applications for each ice accretion measurement technique presented.

The increased use of electrothermal ice protection systems (ETIPSs) in various industries (manned and unmanned aviation, energy production) requires improvements to de-icing efficiency, ice shedding predictability, and energy consumption. To achieve these, a coupled numerical and experimental investigation of ETIPS’s ice removal (ice shedding) mechanism is presented in this paper. Idealized ETIPS de-icing experiments performed in the icing wind tunnel of the von Karman Institute show several ice shedding mechanisms. A one-dimensional phase change solver developed for ice melting simulations highlights the water layer thickness influence over the ice shedding process. Coupled numerical–experimental results are employed to develop an idealized ice shedding model. The model is validated in realistic de-icing experiments in a second experimental campaign in the icing wind tunnel of the LeClerc Icing Research Laboratory.

Atmospheric in-flight icing on unmanned aerial vehicles (UAVs) is a significant hazard. UAVs that are not equipped with ice protection systems are usually limited to operations within visual line of sight or to weather conditions without icing risk. As many military and commercial UAV missions require flights beyond visual line of sight and into adverse weather conditions, energy-efficient ice protection systems are required. In this experimental study, two electro-thermal ice protection systems for fixed-wing UAVs were tested. One system was operated in anti-icing and de-icing mode, and the other system was designed as a parting strip de-icing system. Experiments were conducted in an icing wind tunnel facility for varying icing conditions at low Reynolds numbers. A parametric study over the ice shedding time was used to identify the most energy-efficient operation mode. The results showed that longer intercycle durations led to higher efficiencies and that de-icing with a parting strip was superior compared to anti-icing and de-icing without a parting strip. These findings are relevant for the development of energy-efficient systems in the future.

Although ice shedding generates safety hazards in multiple industries, the phenomenon remains the main de-icing mechanism employed by the popular electro-thermal ice protection systems (ETIPS). To improve the technique’s ice removal capability and minimize its energy consumption, an experimental and numerical investigation of ice shedding produced by ETIPS in de-icing configuration is presented in this paper. An experimental campaign conducted in the von Karman Institute’s (VKI) icing wind tunnel (IWT) shows several ice detachment mechanisms. A one-dimensional phase change solver is developed and used to conduct complementary ice melting simulations. Coupled numerical and experimental results are used to determine the most important ice shedding parameters. Particularly, an ice shedding threshold value of the melted layer thickness produced at the heated surface-ice interface is observed.

This paper presents an experimental, a numerical and a theoretical analysis of the performances of a fluidic vectoring device for controlling the direction of a turbulent, bi-dimensional and low Mach number (incompressible) jet flow. The investigated design is the co-flow secondary injection with Coanda surface, which allows for vectoring angles up to 25° with no need of moving mechanical parts. A simple empirical model of the vectoring process is presented and validated via experimental and numerical data. The experiments consist of flow visualization and image processing for the automatic detection of the jet centerline; the numerical simulations are carried out solving the Unsteady Reynolds Average Navier- Stokes (URANS) closed with the k - ω SST turbulence model, using the PisoFoam solver from OpenFOAM. The experimental validation on three different geometrical configurations has shown that the model is capable of providing a fast and reliable evaluation of the device performance as a function of the operating conditions.

This paper presents an experimental characterization of the jet wiping process, used in continuous coating applications to control the thickness of a liquid coat using an impinging gas jet. Time Resolved Particle Image Velocimetry (TR-PIV) is used to characterize the impinging gas flow, while an automatic interface detection algorithm is developed to track the liquid interface at the impact. The study of the flow interaction is combined with time resolved 3D thickness measurements of the liquid film remaining after the wiping, via Time Resolved Light Absorption (TR-LAbs). The simultaneous frequency analysis of liquid and gas flows allows to correlate their respective instability, provide an experimental data set for the validation of numerical studies and allows for formulating a working hypothesis on the origin of the coat non-uniformity encountered in many jet wiping processes.