Séverine Rossomme
Séverine Rossomme has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Hugo Palmans
National Physical Laboratory
2 shared publications - Ana Lourenço
Medical Radiation Science Group, National Physical Laboratory, Teddington TW11 0LW
1 shared publication - Antoine Delor
Institut Roi Albert II, Cliniques universitaires Saint-Luc, Radiation Oncology department, Brussels
1 shared publication Cécile Goffaux
Bâtiment EOLE
1 shared publication- Damiano Del Sarto
Azienda Ospedaliero Universitaria Pisa AOUP
1 shared publication - Fabio Di Martino
Health Physics Division, University Hospital of Pisa, Pisa, Italy
1 shared publication
Latest Publications
- Open Access
- 15 April 2025
- Published by IOP Publishing in Physics in Medicine & Biology
- Vol. 70 (8) , 085012
Impact of manufacturing tolerances on Monte Carlo calculated k Q , Q 0 factors for plane-parallel ionisation chambers in proton beams
Objective. In the recent update of the TRS-398 Code of Practice (CoP), Monte Carlo results were incorporated into the derivation of recommended beam quality correction factors for ionisation chambers (IC) in proton beams. While the underlying Monte Carlo simulations implement detailed models only based on the nominal geometries from manufacturer blueprints, this paper considers the potential geometric deviations in plane-parallel IC arising from manufacturing tolerances that can reach 10%. Approach. A representative model of a plane-parallel IC has been designed using the Monte Carlo code GATE/Geant4, from which beam quality correction factors have been derived. Subsequently, the results of a reference geometry are compared to those of perturbed geometries, in which the parameters are modified according to the tolerances specified in a standard. Main results. The comparison between the reference and perturbed geometries reveals no significant differences, as they show an agreement within one standard deviation for all the cases studied, with relative deviations not exceeding 0.5%. From these results, we estimate the maximum added uncertainty from manufacturing tolerances on Monte Carlo calculated kQ factors to be about 0.7%. Significance. Overall, the current use of nominal dimensions of plane-parallel IC from manufacturer’s blueprints remains consistent for beam quality correction factor calculations via Monte Carlo simulations, which therefore support the latest results recommended by the TRS-398 CoP.
- 15 April 2025
- Published by IOP Publishing in Physics in Medicine & Biology
- Vol. 70 (8) , 085012
Open AccessImpact of manufacturing tolerances on Monte Carlo calculated k Q , Q 0 factors for plane-parallel ionisation chambers in proton beams
Objective. In the recent update of the TRS-398 Code of Practice (CoP), Monte Carlo results were incorporated into the derivation of recommended beam quality correction factors for ionisation chambers (IC) in proton beams. While the underlying Monte Carlo simulations implement detailed models only based on the nominal geometries from manufacturer blueprints, this paper considers the potential geometric deviations in plane-parallel IC arising from manufacturing tolerances that can reach 10%. Approach. A representative model of a plane-parallel IC has been designed using the Monte Carlo code GATE/Geant4, from which beam quality correction factors have been derived. Subsequently, the results of a reference geometry are compared to those of perturbed geometries, in which the parameters are modified according to the tolerances specified in a standard. Main results. The comparison between the reference and perturbed geometries reveals no significant differences, as they show an agreement within one standard deviation for all the cases studied, with relative deviations not exceeding 0.5%. From these results, we estimate the maximum added uncertainty from manufacturing tolerances on Monte Carlo calculated kQ factors to be about 0.7%. Significance. Overall, the current use of nominal dimensions of plane-parallel IC from manufacturer’s blueprints remains consistent for beam quality correction factor calculations via Monte Carlo simulations, which therefore support the latest results recommended by the TRS-398 CoP.
- 8 November 2023
- Published by Elsevier in Physica Medica
- Vol. 115, 102959
CHARACTERISATION OF SATURATION AND POLARISATION OF DIFFERENT IONISATION CHAMBERS WORKING IN FLASH REGIMEN
- 8 November 2023
- Published by Elsevier in Physica Medica
- Vol. 115, 102959
CHARACTERISATION OF SATURATION AND POLARISATION OF DIFFERENT IONISATION CHAMBERS WORKING IN FLASH REGIMEN
- 1 May 2021
- Published by Elsevier in Zeitschrift für Medizinische Physik
- Vol. 31 (2) , 192-202
Correction of the measured current of a small-gap plane-parallel ionization chamber in proton beams in the presence of charge multiplication
- 1 May 2021
- Published by Elsevier in Zeitschrift für Medizinische Physik
- Vol. 31 (2) , 192-202
Correction of the measured current of a small-gap plane-parallel ionization chamber in proton beams in the presence of charge multiplication
- 25 June 2008
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 20 (3-4) , 293-297
Multi-scale Numerical Modeling of Radial Heat Transfer in Grooved Heat Pipe Evaporators
- 25 June 2008
- Published by Springer Nature in Microgravity Science and Technology
- Vol. 20 (3-4) , 293-297
Multi-scale Numerical Modeling of Radial Heat Transfer in Grooved Heat Pipe Evaporators