Huanhuan Shi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Huanhuan Shi has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Hailong Wang
School of Materials Science and Engineering Zhengzhou University Zhengzhou China
3 shared publications Beibei Wang
Henan Agr Univ, Coll Resources & Environm, Zhengzhou 450002, Peoples R China
2 shared publications- Hongyou Wan
School of Ecology and Environment, Zhengzhou University, Zhengzhou 450001, China
2 shared publications Kehao Zhang
Zhengzhou Univ, Sch Mat Sci & Engn, Zhengzhou 450001, Peoples R China
2 shared publications- Kehao Zhang
School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001, China
2 shared publications Shixiang Gao
Nanjing Univ, Sch Environm, State Key Lab Pollut Control & Resource Reuse, Nanjing 210093, Peoples R China
2 shared publications
Latest Publications
- Open Access
Fate of Per- and Polyfluoroalkyl Substances (PFASs) in Conventional Wastewater Treatment Processes and Strategic Placement of Electrooxidation Units for Enhanced Removal
Per- and polyfluoroalkyl substances pose a high risk to human health globally, and the continuous discharge of PFAS-containing industrial wastewater would worsen the situation. This study examined the effectiveness of conventional wastewater treatment technologies in PFAS removal. The results indicate that primary and secondary sedimentation tanks can remove 8.46–22.65% of long-chain PFCAs (>6 carbons), while PFAA concentration appeared to increase during the anaerobic–oxic process due to biotransformation of PFAA precursors and desorption from activated sludge, ranging from 25.33% for PFBA to 207.31% for PFHxA. Electrooxidation showed effectiveness in PFAS removal in wastewater. Positioning the electrooxidation module between the primary sedimentation tank and the anaerobic–oxic process achieved the lowest energy consumption (63.10 kWh∙m−3) for lowering the perfluorooctanoic acid concentration to meet the standards for drinking water quality in China. The results of this study provide a basis for designing and optimizing PFAS-laden industrial wastewater treatment systems.
Open AccessFate of Per- and Polyfluoroalkyl Substances (PFASs) in Conventional Wastewater Treatment Processes and Strategic Placement of Electrooxidation Units for Enhanced Removal
Per- and polyfluoroalkyl substances pose a high risk to human health globally, and the continuous discharge of PFAS-containing industrial wastewater would worsen the situation. This study examined the effectiveness of conventional wastewater treatment technologies in PFAS removal. The results indicate that primary and secondary sedimentation tanks can remove 8.46–22.65% of long-chain PFCAs (>6 carbons), while PFAA concentration appeared to increase during the anaerobic–oxic process due to biotransformation of PFAA precursors and desorption from activated sludge, ranging from 25.33% for PFBA to 207.31% for PFHxA. Electrooxidation showed effectiveness in PFAS removal in wastewater. Positioning the electrooxidation module between the primary sedimentation tank and the anaerobic–oxic process achieved the lowest energy consumption (63.10 kWh∙m−3) for lowering the perfluorooctanoic acid concentration to meet the standards for drinking water quality in China. The results of this study provide a basis for designing and optimizing PFAS-laden industrial wastewater treatment systems.
- 10 November 2023
- Published by Elsevier in Environmental Research
- Vol. 241, 117612
Electrooxidation of chlorophene and dichlorophen by reactive electrochemical membrane: Key determining factors of removal efficiency
- 10 November 2023
- Published by Elsevier in Environmental Research
- Vol. 241, 117612
Electrooxidation of chlorophene and dichlorophen by reactive electrochemical membrane: Key determining factors of removal efficiency
- Open Access
Construction of Z-Scheme TiO2/Au/BDD Electrodes for an Enhanced Electrocatalytic Performance
TiO2/Au/BDD composites with a Z-scheme structure was prepared by orderly depositing gold (Au) and titanium dioxide (TiO2) on the surface of a boron-doped diamond (BDD) film using sputtering and electrophoretic deposition methods. It was found that the introduction of Au between TiO2 and the BDD, not only could reduce their contact resistance, to increase the carrier transport efficiency, but also could improve the surface Hall mobility of the BDD electrode. Meanwhile, the designed Z-scheme structure provided a fast channel for the electrons and holes combination, to promote the effective separation of the electrons and holes produced in TiO2 and the BDD under photoirradiation. The electrochemical characterization elucidated that these modifications of the structure obviously enhanced the electrocatalytic performance of the electrode, which was further verified by the simulated wastewater degradation experiments with reactive brilliant red X-3B. In addition, it was also found that the photoirradiation effectively enhanced the pollution degradation efficiency of the modified electrode, especially for the TiO2/Au/BDD-30 electrode.
Open AccessConstruction of Z-Scheme TiO2/Au/BDD Electrodes for an Enhanced Electrocatalytic Performance
TiO2/Au/BDD composites with a Z-scheme structure was prepared by orderly depositing gold (Au) and titanium dioxide (TiO2) on the surface of a boron-doped diamond (BDD) film using sputtering and electrophoretic deposition methods. It was found that the introduction of Au between TiO2 and the BDD, not only could reduce their contact resistance, to increase the carrier transport efficiency, but also could improve the surface Hall mobility of the BDD electrode. Meanwhile, the designed Z-scheme structure provided a fast channel for the electrons and holes combination, to promote the effective separation of the electrons and holes produced in TiO2 and the BDD under photoirradiation. The electrochemical characterization elucidated that these modifications of the structure obviously enhanced the electrocatalytic performance of the electrode, which was further verified by the simulated wastewater degradation experiments with reactive brilliant red X-3B. In addition, it was also found that the photoirradiation effectively enhanced the pollution degradation efficiency of the modified electrode, especially for the TiO2/Au/BDD-30 electrode.
- Open Access
- 25 October 2022
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 19 (21) , 13840
A Case Study of Swine Wastewater Treatment via Electrochemical Oxidation by Ti4O7 Anode
With the rapid development of breeding industry, the efficient treatment of dramatically increasing swine wastewater is gradually becoming urgent. In particular, the development of application technologies suitable for the relatively small piggeries is critical due to the time cost and space requirements of conventional biological methods. In this study, Electrochemical oxidation (EO) was selected to systematically explore the treatment performance of three different swine wastewaters by Ti4O7 anode. It was observed that the colors changed from dark brown to light yellow after 60 min treatment at 50 mA/cm2, and the removal rates of turbidity and suspended solids ranged from 89.36% to 93.65% and 81.31% to 92.55%, respectively. The chemical oxygen demand (COD), ammonia nitrogen (NH3-N) and total phosphorus (TP) of all the three swine wastewaters were simultaneously removed to a very low concentration in 120 min, especially for sample III, 61 ± 9 mg/L of COD, 6.6 ± 0.4 mg/L of NH3-N and 5.7 ± 1.1 mg/L of TP, which met the Discharge Standard of Pollutants for Livestock and Poultry Breeding (GB 18596-2001). Moreover, 70.93%–85.37% mineralization rates were also achieved in 120 min, confirming that EO treatment by Ti4O7 could efficiently remove the organic matters in wastewater. Excitation–emission matrix (EEM) and UV-vis spectrum characterization results further proved that aromatic compounds and macromolecules in wastewater were rapidly removed, which played important roles in the mineralization processes. The findings here provided an efficient and environment-friendly technology for swine wastewater treatment.
- 25 October 2022
- Published by MDPI AG in International Journal of Environmental Research and Public Health
- Vol. 19 (21) , 13840
Open AccessA Case Study of Swine Wastewater Treatment via Electrochemical Oxidation by Ti4O7 Anode
With the rapid development of breeding industry, the efficient treatment of dramatically increasing swine wastewater is gradually becoming urgent. In particular, the development of application technologies suitable for the relatively small piggeries is critical due to the time cost and space requirements of conventional biological methods. In this study, Electrochemical oxidation (EO) was selected to systematically explore the treatment performance of three different swine wastewaters by Ti4O7 anode. It was observed that the colors changed from dark brown to light yellow after 60 min treatment at 50 mA/cm2, and the removal rates of turbidity and suspended solids ranged from 89.36% to 93.65% and 81.31% to 92.55%, respectively. The chemical oxygen demand (COD), ammonia nitrogen (NH3-N) and total phosphorus (TP) of all the three swine wastewaters were simultaneously removed to a very low concentration in 120 min, especially for sample III, 61 ± 9 mg/L of COD, 6.6 ± 0.4 mg/L of NH3-N and 5.7 ± 1.1 mg/L of TP, which met the Discharge Standard of Pollutants for Livestock and Poultry Breeding (GB 18596-2001). Moreover, 70.93%–85.37% mineralization rates were also achieved in 120 min, confirming that EO treatment by Ti4O7 could efficiently remove the organic matters in wastewater. Excitation–emission matrix (EEM) and UV-vis spectrum characterization results further proved that aromatic compounds and macromolecules in wastewater were rapidly removed, which played important roles in the mineralization processes. The findings here provided an efficient and environment-friendly technology for swine wastewater treatment.
- Open Access
Green Synthesis of A Novel MXene–CS Composite Applied in Treatment of Cr(VI) Contaminated Aqueous Solution
The considerable amount of Cr(VI) pollutants in the aqueous environment is a significant environmental concern that cannot be ignored. A series of novel Mxene–CS inorganic–organic composite nanomaterials synthesized by using the solution reaction method was applied to treat the Cr(VI) contaminated water. The Mxene–CS composites were characterized through SEM (scanning electron microscope), XRD (X–ray diffraction), XPS (X–ray photoelectron spectroscopy), and FTIR (Fourier transform infrared). The XRD patterns (observed at 2θ of 18.1°, 35.8°, 41.5°, and 60.1°) and the FT–IR spectra (-NH2 group for 1635 and 1517 cm−1, and -OH group for 3482 cm−1) illustrated that CS was successfully loaded on the Mxene. The effects of solution pH, the dosage of Mxene–CS, and duration time on the adsorption of Cr(VI) by synthesized Mxene–CS were investigated. The removal efficiency of Cr(VI) was increased from 12.9% to 40.5% with Mxene–CS dosage ranging from 0.02 to 0.12 g/L. The adsorption process could be well fitted by the pseudo–second–order kinetics model, indicating chemisorption occurred. The Langmuir isotherm model could be better to describe the process with a maximum adsorption capacity of 43.1 mg/g. The prepared novel Mxene–CS composite was considered as an alternative for adsorption of heavy metals from wastewater.
Open AccessGreen Synthesis of A Novel MXene–CS Composite Applied in Treatment of Cr(VI) Contaminated Aqueous Solution
The considerable amount of Cr(VI) pollutants in the aqueous environment is a significant environmental concern that cannot be ignored. A series of novel Mxene–CS inorganic–organic composite nanomaterials synthesized by using the solution reaction method was applied to treat the Cr(VI) contaminated water. The Mxene–CS composites were characterized through SEM (scanning electron microscope), XRD (X–ray diffraction), XPS (X–ray photoelectron spectroscopy), and FTIR (Fourier transform infrared). The XRD patterns (observed at 2θ of 18.1°, 35.8°, 41.5°, and 60.1°) and the FT–IR spectra (-NH2 group for 1635 and 1517 cm−1, and -OH group for 3482 cm−1) illustrated that CS was successfully loaded on the Mxene. The effects of solution pH, the dosage of Mxene–CS, and duration time on the adsorption of Cr(VI) by synthesized Mxene–CS were investigated. The removal efficiency of Cr(VI) was increased from 12.9% to 40.5% with Mxene–CS dosage ranging from 0.02 to 0.12 g/L. The adsorption process could be well fitted by the pseudo–second–order kinetics model, indicating chemisorption occurred. The Langmuir isotherm model could be better to describe the process with a maximum adsorption capacity of 43.1 mg/g. The prepared novel Mxene–CS composite was considered as an alternative for adsorption of heavy metals from wastewater.