Liqing Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Liqing Xu has a total of 434 co-authors. Here are the top co-authors by number of shared publications:
Liqun Hu
Chinese Acad Sci, Inst Plasma Phys, Hefei Inst Phys Sci, Hefei 230031, Peoples R China
23 shared publicationsYanmin Duan
Chinese Academy of Sciences Hefei Institutes of Physical Science Institute of Plasma Physics
13 shared publicationsShiyao Lin
Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031, China, Hefei, 230031
12 shared publications- Bin Zhang
Institute of Plasma Physics, Hefei Institutes of Physical Science, Chinese Academy of Sciences, Hefei 230031, People’s Republic of China
11 shared publications Kaiyun Chen
Chinese Academy of Sciences Institute of Plasma Physics
11 shared publications- Hai-Qing Liu
Institute of Plasma Physics, Hefei Institutes of Physical Science, Chinese Academy of Sciences 1 , Hefei 230031
10 shared publications
Latest Publications
- Open Access
- 10 November 2026
- Published by IOP Publishing in Nuclear Fusion
Damping and accumulation characteristics of flow driven by fishbone instability
The persistence of fishbone-driven flows across successive bursts is critical to their potential role in regulating turbulence and improving core confinement, yet the damping characteristics of such flows have not been experimentally characterized. Here we report the first direct measurement of the damping rate of fishbone-driven flows using Doppler reflectometry on the EAST tokamak. The experimentally obtained damping rate exceeds prior theoretical predictions, and this discrepancy can be reconciled by incorporating the effective charge number $Z_{\text{eff}}$ into the accalculation of the damping rate. Furthermore, we observe that flow accumulation occurs when the time interval between successive fishbone bursts is sufficiently short, and we estimate the critical inter-burst interval threshold for accumulation to be approximately 1 ms under the present discharge conditions. These results establish an essential experimental foundation for understanding the temporal persistence of fishbone-driven flows and their implications for transport barrier dynamics.- 10 November 2026
- Published by IOP Publishing in Nuclear Fusion
Open AccessDamping and accumulation characteristics of flow driven by fishbone instability
The persistence of fishbone-driven flows across successive bursts is critical to their potential role in regulating turbulence and improving core confinement, yet the damping characteristics of such flows have not been experimentally characterized. Here we report the first direct measurement of the damping rate of fishbone-driven flows using Doppler reflectometry on the EAST tokamak. The experimentally obtained damping rate exceeds prior theoretical predictions, and this discrepancy can be reconciled by incorporating the effective charge number $Z_{\text{eff}}$ into the accalculation of the damping rate. Furthermore, we observe that flow accumulation occurs when the time interval between successive fishbone bursts is sufficiently short, and we estimate the critical inter-burst interval threshold for accumulation to be approximately 1 ms under the present discharge conditions. These results establish an essential experimental foundation for understanding the temporal persistence of fishbone-driven flows and their implications for transport barrier dynamics. - 21 October 2026
- Published by IOP Publishing in Plasma Science and Technology
Application of a minimum Fisher information method with flexible boundary conditions to soft X-ray tomography on EAST
Soft X-ray (SXR) tomography is essential for resolving magnetohydrodynamic (MHD) instability structures in the EAST tokamak. Two tomographic methods have been established at EAST: the Fourier--Bessel (F--B) expansion method and the Gaussian Process (GP) method, and a deep-learning-based imaging approach has also been explored. The minimum Fisher information (MFI) method, with anisotropic regularization aligned to the magnetic flux surfaces, has been successfully applied on several tokamaks, including JET with only two viewing chords. In this work we adapt it to the three-camera SXR diagnostic at EAST, where the flux-surface grid implementation raises a boundary problem. We reformulate it as a flexible-boundary MFI method that introduces no additional free hyperparameters. Validation on synthetic phantoms with known emissivity, together with experimental results on EAST sawtooth, fishbone, and tearing modes, demonstrates that the flexible-boundary MFI achieves imaging quality comparable to the GP method while using fewer free hyperparameters than both GP and F--B, thus providing EAST with a physically reliable SXR tomographic tool and enabling multi-method cross-comparison of emissivity reconstructions.
- 21 October 2026
- Published by IOP Publishing in Plasma Science and Technology
Application of a minimum Fisher information method with flexible boundary conditions to soft X-ray tomography on EAST
Soft X-ray (SXR) tomography is essential for resolving magnetohydrodynamic (MHD) instability structures in the EAST tokamak. Two tomographic methods have been established at EAST: the Fourier--Bessel (F--B) expansion method and the Gaussian Process (GP) method, and a deep-learning-based imaging approach has also been explored. The minimum Fisher information (MFI) method, with anisotropic regularization aligned to the magnetic flux surfaces, has been successfully applied on several tokamaks, including JET with only two viewing chords. In this work we adapt it to the three-camera SXR diagnostic at EAST, where the flux-surface grid implementation raises a boundary problem. We reformulate it as a flexible-boundary MFI method that introduces no additional free hyperparameters. Validation on synthetic phantoms with known emissivity, together with experimental results on EAST sawtooth, fishbone, and tearing modes, demonstrates that the flexible-boundary MFI achieves imaging quality comparable to the GP method while using fewer free hyperparameters than both GP and F--B, thus providing EAST with a physically reliable SXR tomographic tool and enabling multi-method cross-comparison of emissivity reconstructions.
- 1 September 2026
- Published by AIP Publishing in Physics of Plasmas
- Vol. 33 (9)
Investigation of reversed shear Alfvén eigenmodes (RSAE) in relation to internal transport barrier (ITB) for high-qmin scenario on EAST
The reversed shear Alfvén eigenmode (RSAE) and the relationship with the internal transport barrier (ITB) have been investigated in the Experimental Advanced Superconducting Tokamak for the high qmin scenario. The RSAE with low toroidal mode numbers (1 ≤n< 5) is distributed within the normalized minor radius range of 0.2 ≤ρ≤ 0.4. Furthermore, two distinct RSAE branches with similar toroidal mode numbers but different radial coverage and phase profiles are observed. The excitation of RSAE leads to a redistribution of fast ions, with the density change predominantly in the central region enclosed by the minimum safety factor (qmin), as measured by the radial neutron camera. A micro-instability characterized by thermal particle transport has been detected by the POLarimeter-INTerferometer diagnostic, which is excited concurrently after the upward sweeping frequency of RSAE. The inward shift of the inner q = 2 surface is indicated by a sawteeth-like collapse event (Δr≈ 2 cm, Δr/a≈ 5%, a is the plasma minor radius), accompanied by a comparable outward shift in the R/LTi profile [R/LTi is the normalized ion temperature gradient (ITG) scale length]. These profile modifications, which subsequently suppress thermal particle transport, are correlated with a decrease in magnetic shear. The formation of Ti-ITB, characterized by R/LTi≥ 10, is observed following the RSAE instability under conditions of high neutral beam injection and ion cyclotron resonance heating power. A negative radial electric field (Er) is observed at the position of qmin≈2, and the E×B shear rate significantly increases after the formation of ITB. Furthermore, the RSAE experiences partial suppression due to the improved ITG; however, it becomes fully suppressed after ITB formation and subsequently recovers following the ITB collapse.
- 1 September 2026
- Published by AIP Publishing in Physics of Plasmas
- Vol. 33 (9)
Investigation of reversed shear Alfvén eigenmodes (RSAE) in relation to internal transport barrier (ITB) for high-qmin scenario on EAST
The reversed shear Alfvén eigenmode (RSAE) and the relationship with the internal transport barrier (ITB) have been investigated in the Experimental Advanced Superconducting Tokamak for the high qmin scenario. The RSAE with low toroidal mode numbers (1 ≤n< 5) is distributed within the normalized minor radius range of 0.2 ≤ρ≤ 0.4. Furthermore, two distinct RSAE branches with similar toroidal mode numbers but different radial coverage and phase profiles are observed. The excitation of RSAE leads to a redistribution of fast ions, with the density change predominantly in the central region enclosed by the minimum safety factor (qmin), as measured by the radial neutron camera. A micro-instability characterized by thermal particle transport has been detected by the POLarimeter-INTerferometer diagnostic, which is excited concurrently after the upward sweeping frequency of RSAE. The inward shift of the inner q = 2 surface is indicated by a sawteeth-like collapse event (Δr≈ 2 cm, Δr/a≈ 5%, a is the plasma minor radius), accompanied by a comparable outward shift in the R/LTi profile [R/LTi is the normalized ion temperature gradient (ITG) scale length]. These profile modifications, which subsequently suppress thermal particle transport, are correlated with a decrease in magnetic shear. The formation of Ti-ITB, characterized by R/LTi≥ 10, is observed following the RSAE instability under conditions of high neutral beam injection and ion cyclotron resonance heating power. A negative radial electric field (Er) is observed at the position of qmin≈2, and the E×B shear rate significantly increases after the formation of ITB. Furthermore, the RSAE experiences partial suppression due to the improved ITG; however, it becomes fully suppressed after ITB formation and subsequently recovers following the ITB collapse.
- 1 September 2026
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 68 (9) , 095022
Observation of fast ion acceleration under EGAM in EAST pure ECRH plasma with tearing mode
In magnetically confined fusion plasmas heated only by electron cyclotron resonance heating (ECRH), ion temperature typically saturates in the 1–3 keV range. The EAST tokamak, equipped with an ITER-like tungsten divertor, has operated deuterium H-mode discharges with high-power pure ECRH. In a specific discharge, a continuous ion acceleration process is observed, with ion energy ranging from an off-axis supra-thermal component above 6 keV to an isolated Gaussian peak reaching 1.8 MeV. The acceleration occurs at the location of a large 2/1 magnetic island, and an EGAM-like electrostatic mode at ∼ 23 kHz is detected by microwave diagnostics. The MeV-range cutoff energy, the mode power, and the island width exhibit pairwise strong linear correlations ( R 2 > 0.9 ), and the three are spatially coincident. Transfer entropy analysis and a 0D collisional-radiative model suggest a mechanism from island to mode to ion acceleration, excluding a purely electric-field-driven process. These observations provide experimental evidence of MeV-range ion acceleration accompanied by an EGAM-like mode in a pure ECRH plasma without auxiliary ion heating, offering a new data point for understanding ion acceleration under ECRH operation in tungsten-wall devices, particularly with degraded boron wall coating.
- 1 September 2026
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 68 (9) , 095022
Observation of fast ion acceleration under EGAM in EAST pure ECRH plasma with tearing mode
In magnetically confined fusion plasmas heated only by electron cyclotron resonance heating (ECRH), ion temperature typically saturates in the 1–3 keV range. The EAST tokamak, equipped with an ITER-like tungsten divertor, has operated deuterium H-mode discharges with high-power pure ECRH. In a specific discharge, a continuous ion acceleration process is observed, with ion energy ranging from an off-axis supra-thermal component above 6 keV to an isolated Gaussian peak reaching 1.8 MeV. The acceleration occurs at the location of a large 2/1 magnetic island, and an EGAM-like electrostatic mode at ∼ 23 kHz is detected by microwave diagnostics. The MeV-range cutoff energy, the mode power, and the island width exhibit pairwise strong linear correlations ( R 2 > 0.9 ), and the three are spatially coincident. Transfer entropy analysis and a 0D collisional-radiative model suggest a mechanism from island to mode to ion acceleration, excluding a purely electric-field-driven process. These observations provide experimental evidence of MeV-range ion acceleration accompanied by an EGAM-like mode in a pure ECRH plasma without auxiliary ion heating, offering a new data point for understanding ion acceleration under ECRH operation in tungsten-wall devices, particularly with degraded boron wall coating.
- Open Access
- 1 July 2026
- Published by AIP Publishing in Physics of Plasmas
- Vol. 33 (7)
Runaway plateau formation in EAST disruptions triggered by massive gases injection
Runaway-electron (RE) plateaus have been observed during disruptions in experimental advanced superconducting tokamak (EAST) plasmas following the massive injection of argon into low-density ohmic discharges, which are performed with a circular plasma configuration under full-metal wall conditions. RE plateaus can maximally carry a current of 270 kA and last up to 400 ms. The formation of RE plateaus strongly depends on lower pre-disruption electron densities (0.2–0.5 × 1019 m−3) and a lower amount of argon injection (400–1000 Pa l), which correspond to an enhanced pre-disruption RE population and a reduced post-disruption electron density, respectively. Pre-disruption REs were found to survive the thermal quench, serving as extra seeds for the RE plateau. In addition, magnetohydrodynamic activity during the thermal quench was found to cause significant RE loss and affect RE plateau formation; in particular, the m/n = 3/1 and m/n = 2/1 modes were observed in sequence, leading to distinct RE loss patterns. Simulations on RE generation by a 0D model further confirmed the key roles of RE seeds to form an RE plateau in EAST.
- 1 July 2026
- Published by AIP Publishing in Physics of Plasmas
- Vol. 33 (7)
Open AccessRunaway plateau formation in EAST disruptions triggered by massive gases injection
Runaway-electron (RE) plateaus have been observed during disruptions in experimental advanced superconducting tokamak (EAST) plasmas following the massive injection of argon into low-density ohmic discharges, which are performed with a circular plasma configuration under full-metal wall conditions. RE plateaus can maximally carry a current of 270 kA and last up to 400 ms. The formation of RE plateaus strongly depends on lower pre-disruption electron densities (0.2–0.5 × 1019 m−3) and a lower amount of argon injection (400–1000 Pa l), which correspond to an enhanced pre-disruption RE population and a reduced post-disruption electron density, respectively. Pre-disruption REs were found to survive the thermal quench, serving as extra seeds for the RE plateau. In addition, magnetohydrodynamic activity during the thermal quench was found to cause significant RE loss and affect RE plateau formation; in particular, the m/n = 3/1 and m/n = 2/1 modes were observed in sequence, leading to distinct RE loss patterns. Simulations on RE generation by a 0D model further confirmed the key roles of RE seeds to form an RE plateau in EAST.
- Open Access
- 3 April 2025
- Published by IOP Publishing in Nuclear Fusion
- Vol. 65 (5) , 056011
Research on stiff transport in electron heating dominated plasmas in EAST
An experiment was conducted on the Experimental Advanced Superconducting Tokamak (EAST) to investigate the properties of stiff transport in an electron-heated H-mode plasma, using a power deposition scan with electron cyclotron resonance heating (ECRH). During this experiment, a shift in lower hybrid wave heating power and driven current from the plasma core to the outer regions was observed, accompanied by a change in the local magnetic shear. Transport analysis reveals a reduction in the normalized effective electron thermal diffusivity ( χ e ) at larger minor radii when ECRH was applied off-axis, in alignment with the turbulent instability analysis. A threshold for the stiff transport is identified around R / L Te ∼ 3 on EAST, above which the electron heat flux (q e) increases sharply with R / L Te . Moreover, experimental and simulation results indicate that the change in ECRH power deposition influences local micro-instability turbulence, resulting in the transition of TEM to ITG modes, thereby affecting the plasma performance. These findings provide important insights for optimizing plasma performance, improving confinement, and advancing our understanding of plasma transport in future fusion reactors.
- 3 April 2025
- Published by IOP Publishing in Nuclear Fusion
- Vol. 65 (5) , 056011
Open AccessResearch on stiff transport in electron heating dominated plasmas in EAST
An experiment was conducted on the Experimental Advanced Superconducting Tokamak (EAST) to investigate the properties of stiff transport in an electron-heated H-mode plasma, using a power deposition scan with electron cyclotron resonance heating (ECRH). During this experiment, a shift in lower hybrid wave heating power and driven current from the plasma core to the outer regions was observed, accompanied by a change in the local magnetic shear. Transport analysis reveals a reduction in the normalized effective electron thermal diffusivity ( χ e ) at larger minor radii when ECRH was applied off-axis, in alignment with the turbulent instability analysis. A threshold for the stiff transport is identified around R / L Te ∼ 3 on EAST, above which the electron heat flux (q e) increases sharply with R / L Te . Moreover, experimental and simulation results indicate that the change in ECRH power deposition influences local micro-instability turbulence, resulting in the transition of TEM to ITG modes, thereby affecting the plasma performance. These findings provide important insights for optimizing plasma performance, improving confinement, and advancing our understanding of plasma transport in future fusion reactors.
- 1 April 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (4)
Development of x-ray imaging diagnostics on Experimental Advanced Superconducting Tokamak using Timepix3 detector
An x-ray imaging diagnostic system using the Timepix3 detector has recently been developed and installed on the Experimental Advanced Superconducting Tokamak (EAST). The diagnostic system measures the temporal evolution, spatial distribution, and energy spectrum of x-ray signals during plasma discharge with a 16° diagonal field of view, spatial resolution of 4 mm, and broad spectral-energy response range (5–200 keV). Equipped with event-driven capability, the Timepix3 detector captures the coordinates, energy, and arrival time of each photon event with a temporal resolution of 1.56 ns. Herein, the energy resolution and spatial resolution performances of the detector were tested in counting and time-over-threshold modes. The energy resolution of the detector in both modes was within 5 keV. The temporal resolution of the detector and the temporal evolution of x-ray signals were analyzed during plasma discharge experiments on the EAST, harnessing the event-driven capability of the detector for latter analysis. Furthermore, the detector-measured signals were compared with conventional diagnostic signals, confirming the reliability of the Timepix3 detector. Overall, this paper presents the parameter testing results and preliminary experimental diagnostic outcomes.
- 1 April 2025
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 96 (4)
Development of x-ray imaging diagnostics on Experimental Advanced Superconducting Tokamak using Timepix3 detector
An x-ray imaging diagnostic system using the Timepix3 detector has recently been developed and installed on the Experimental Advanced Superconducting Tokamak (EAST). The diagnostic system measures the temporal evolution, spatial distribution, and energy spectrum of x-ray signals during plasma discharge with a 16° diagonal field of view, spatial resolution of 4 mm, and broad spectral-energy response range (5–200 keV). Equipped with event-driven capability, the Timepix3 detector captures the coordinates, energy, and arrival time of each photon event with a temporal resolution of 1.56 ns. Herein, the energy resolution and spatial resolution performances of the detector were tested in counting and time-over-threshold modes. The energy resolution of the detector in both modes was within 5 keV. The temporal resolution of the detector and the temporal evolution of x-ray signals were analyzed during plasma discharge experiments on the EAST, harnessing the event-driven capability of the detector for latter analysis. Furthermore, the detector-measured signals were compared with conventional diagnostic signals, confirming the reliability of the Timepix3 detector. Overall, this paper presents the parameter testing results and preliminary experimental diagnostic outcomes.
- Open Access
- 11 November 2024
- Published by IOP Publishing in Nuclear Fusion
- Vol. 65 (1) , 016001
Observation of nonthermal electrons further acceleration and long-lasting associated with magnetic reconnection and turbulence bursting in tokamak plasma
Vital to magnetized plasma performance, the acceleration of nonthermal electrons significantly influences the current drive of radio frequency (RF) waves in plasma. In Experimental Advanced Superconducting Tokamak (EAST), we observed nonthermal electrons initially <215 keV in energy, being locally accelerated to 600 keV within 100 milliseconds, which corresponds to the total growth time of the magnetic island. Surprisingly, these fast electrons (FEs) lasted for 1.4 s, several times longer than the estimated relaxation time of 0.26 s, and exceeded 1/10 of the discharge length. Turbulence generation at island’s X point is attributed to the unexpected confinement and repopulation of FEs. This phenomenon may have positive implications for the steady-state long pulse H mode operation in EAST, especially regarding non-inductive current sustainment. For future RF electron heating-dominant devices, the mechanisms elucidated in this study have immediate implications for optimizing RF current drive efficiency.
- 11 November 2024
- Published by IOP Publishing in Nuclear Fusion
- Vol. 65 (1) , 016001
Open AccessObservation of nonthermal electrons further acceleration and long-lasting associated with magnetic reconnection and turbulence bursting in tokamak plasma
Vital to magnetized plasma performance, the acceleration of nonthermal electrons significantly influences the current drive of radio frequency (RF) waves in plasma. In Experimental Advanced Superconducting Tokamak (EAST), we observed nonthermal electrons initially <215 keV in energy, being locally accelerated to 600 keV within 100 milliseconds, which corresponds to the total growth time of the magnetic island. Surprisingly, these fast electrons (FEs) lasted for 1.4 s, several times longer than the estimated relaxation time of 0.26 s, and exceeded 1/10 of the discharge length. Turbulence generation at island’s X point is attributed to the unexpected confinement and repopulation of FEs. This phenomenon may have positive implications for the steady-state long pulse H mode operation in EAST, especially regarding non-inductive current sustainment. For future RF electron heating-dominant devices, the mechanisms elucidated in this study have immediate implications for optimizing RF current drive efficiency.
- Open Access
- 28 September 2024
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 41
Density compensation with pellet fueling during ELM suppression with n = 4 RMP on metal-wall EAST tokamak
- 28 September 2024
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 41
Open AccessDensity compensation with pellet fueling during ELM suppression with n = 4 RMP on metal-wall EAST tokamak
- Open Access
- 1 April 2024
- Published by AIP Publishing in Physics of Plasmas
- Vol. 31 (4)
Experiment study of m/n = 1/1 mode saturation level in high-βp discharge on the EAST tokamak
The saturated internal kink mode with m/n = 1/1 has been observed in the H-mode discharge of the experimental advanced superconducting tokamak, characterized by high βP and weak magnetic shear in the core. This observation was made using a combination of soft x-ray imaging and electron cyclotron emission diagnostics. It was noted that the repetitive bursting of m/n = 1/1 internal mode (large amplitude, short bursting duration) transitions into a long-lasting continuous one (small amplitude, constant frequency), when βp> 2.2 in H-mode, a much shorter bursting duration, transitioning into a long-lasting continuous one, with smaller amplitude and a constant frequency. Conversely, for typical βp< 1.5 in L/I discharge, the frequency of m/n = 1/1 mode decreases with time, associated with local poloidal electron diamagnetism drift velocity. The benign m/n = 1/1 mode in high βp has an amplitude much smaller than one in L-mode for high βP stabilization effect. By adjusting the power deposition of electron cyclotron resonance heating, it is found that the saturation level of m/n = 1/1 mode is independent of the local electron temperature gradient in H-mode discharge. It underscores that the flat current and, hence, weak magnetic shear are crucial factors influencing the saturation level of the m/n = 1/1 mode for both the off-axis electron cyclotron current driving current-dominant and off-axis bootstrap current-dominant cases. Furthermore, the outward movement with growth of the m/n = 1/1 mode in the process of L-H mode transition and the characteristic time of this process are close to the current diffusion time.
- 1 April 2024
- Published by AIP Publishing in Physics of Plasmas
- Vol. 31 (4)
Open AccessExperiment study of m/n = 1/1 mode saturation level in high-βp discharge on the EAST tokamak
The saturated internal kink mode with m/n = 1/1 has been observed in the H-mode discharge of the experimental advanced superconducting tokamak, characterized by high βP and weak magnetic shear in the core. This observation was made using a combination of soft x-ray imaging and electron cyclotron emission diagnostics. It was noted that the repetitive bursting of m/n = 1/1 internal mode (large amplitude, short bursting duration) transitions into a long-lasting continuous one (small amplitude, constant frequency), when βp> 2.2 in H-mode, a much shorter bursting duration, transitioning into a long-lasting continuous one, with smaller amplitude and a constant frequency. Conversely, for typical βp< 1.5 in L/I discharge, the frequency of m/n = 1/1 mode decreases with time, associated with local poloidal electron diamagnetism drift velocity. The benign m/n = 1/1 mode in high βp has an amplitude much smaller than one in L-mode for high βP stabilization effect. By adjusting the power deposition of electron cyclotron resonance heating, it is found that the saturation level of m/n = 1/1 mode is independent of the local electron temperature gradient in H-mode discharge. It underscores that the flat current and, hence, weak magnetic shear are crucial factors influencing the saturation level of the m/n = 1/1 mode for both the off-axis electron cyclotron current driving current-dominant and off-axis bootstrap current-dominant cases. Furthermore, the outward movement with growth of the m/n = 1/1 mode in the process of L-H mode transition and the characteristic time of this process are close to the current diffusion time.