Takanori Mimura
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Takanori Mimura has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Hiroshi Funakubo
Institute of Science Tokyo
11 shared publications - Takao Shimizu
National Institute for Materials Science
8 shared publications - Jon Ihlefeld
Department of Materials Science and Engineering, University of Virginia 1 , Charlottesville, Virginia 22904
3 shared publications - Osami Sakata
Japan Synchrotron Radiation Research Institute
3 shared publications Reijiro Shimura
Department of Materials Science and Engineering, Tokyo Institute of Technology, 4259 Nagatsuta-cho, Midori-ku, Yokohama, Kanagawa 226-8503, Japan
3 shared publicationsKazuki Okamoto
Department of Materials Science and Engineering, Tokyo Institute of Technology, Yokohama, Kanagawa 226-8503, Japan
2 shared publications
Latest Publications
- 1 March 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (3) , 030001
Advances and challenges in novel non-perovskite-based ferroelectrics film for memory device applications
Thin films of ferroelectric materials have been investigated for various applications because of their high dielectric constants, as well as piezoelectric and ferroelectric properties. Ferroelectricity has been explored for memory applications because of its two stable states after releasing an electric field, depending on the direction. Perovskite-based ferroelectrics have been studied for the last 30 years for these applications and have already been commercialized. However, the degradation of their ferroelectricity with decreasing film thickness (below about 30 nm) makes high-density memory applications difficult. A recent “discovery” of novel ferroelectrics, e.g., fluorite-type structure HfO2-based films and wurtzite structure AlN-, GaN-, and ZnO-based films, have enabled significant reductions in film thickness without noticeable degradation. In this article, we discuss the status and challenges of these novel non-perovskite-based ferroelectric films mainly for memory device applications.
- 1 March 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (3) , 030001
Advances and challenges in novel non-perovskite-based ferroelectrics film for memory device applications
Thin films of ferroelectric materials have been investigated for various applications because of their high dielectric constants, as well as piezoelectric and ferroelectric properties. Ferroelectricity has been explored for memory applications because of its two stable states after releasing an electric field, depending on the direction. Perovskite-based ferroelectrics have been studied for the last 30 years for these applications and have already been commercialized. However, the degradation of their ferroelectricity with decreasing film thickness (below about 30 nm) makes high-density memory applications difficult. A recent “discovery” of novel ferroelectrics, e.g., fluorite-type structure HfO2-based films and wurtzite structure AlN-, GaN-, and ZnO-based films, have enabled significant reductions in film thickness without noticeable degradation. In this article, we discuss the status and challenges of these novel non-perovskite-based ferroelectric films mainly for memory device applications.
- 2 September 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (9) , 09SP17
Ta5+-substitution effects on crystal structure and ferroelectric property in HfO2-based films
To investigate the Ta5+-substitution effects on crystal structure and ferroelectric property in HfO2-based films, Ta x Hf1−x O2+δ films with various film thicknesses and Ta content were prepared. The ferroelectric orthorhombic phase was formed in a wide film thickness range of 20–100 nm while in a narrow composition range of x = 0.10–0.14. These thickness-insensitive and composition-sensitive characteristics of Ta5+-substituted HfO2 film are similar to Y3+ rather than Zr4+. The X-ray photoelectron spectroscopy measurement suggests that the ionic state of Ta is not reduced and Ta x Hf1−x O2+δ film has an excess oxygen state. The excess oxygen may consist of a combination of oxygen vacancies and more interstitial oxygens. These defects facilitate the formation of the ferroelectric phasebut also decrease the breakdown voltage and increase the leakage current in Ta5+-substituted HfO2 films. On the other hand, the generation of excess oxygen indicates the possibility of controlling oxygen vacancies which deteriorate fatigue and retention properties.
- 2 September 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (9) , 09SP17
Ta5+-substitution effects on crystal structure and ferroelectric property in HfO2-based films
To investigate the Ta5+-substitution effects on crystal structure and ferroelectric property in HfO2-based films, Ta x Hf1−x O2+δ films with various film thicknesses and Ta content were prepared. The ferroelectric orthorhombic phase was formed in a wide film thickness range of 20–100 nm while in a narrow composition range of x = 0.10–0.14. These thickness-insensitive and composition-sensitive characteristics of Ta5+-substituted HfO2 film are similar to Y3+ rather than Zr4+. The X-ray photoelectron spectroscopy measurement suggests that the ionic state of Ta is not reduced and Ta x Hf1−x O2+δ film has an excess oxygen state. The excess oxygen may consist of a combination of oxygen vacancies and more interstitial oxygens. These defects facilitate the formation of the ferroelectric phasebut also decrease the breakdown voltage and increase the leakage current in Ta5+-substituted HfO2 films. On the other hand, the generation of excess oxygen indicates the possibility of controlling oxygen vacancies which deteriorate fatigue and retention properties.
- 5 April 2024
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 6 (4) , 2500-2506
Phase Identification of 850 nm Thick 7%YO1.5–93%HfO2 Films by Surface and Cross-Sectional Raman Spectroscopies
- 5 April 2024
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 6 (4) , 2500-2506
Phase Identification of 850 nm Thick 7%YO1.5–93%HfO2 Films by Surface and Cross-Sectional Raman Spectroscopies
- Open Access
- 25 June 2023
- Published by Wiley in Physica Status Solidi (a)
- Vol. 220 (14)
No‐Heating Deposition of Ferroelectric x%YO1.5–(100−x%)(Hf1−yZry)O2 Films
The no‐heating deposition of x%YO1.5–(100−x%)(Hf1−yZry)O2 (x = 0−0.09, y = 0, 0.25, 0.50, and 1) is achieved using a radio‐frequency magnetron sputtering method. To investigate the crystal structure and ferroelectric properties, epitaxial films are grown on (111)‐oriented indium tin oxide (ITO)/(111) Y‐stabilized zirconia (YSZ) substrates. The ferroelectric orthorhombic phase is obtained for the 5–7%YO1.5–95–93%HfO2 and 5%YO1.5–95% (Hf0.75Zr0.25)O2 films. The field‐induced phase transition from tetragonal to orthorhombic is confirmed for the 8%YO1.5–92%HfO2 and 5%YO1.5–95%(Hf0.50Zr0.50)O2 films. The remnant polarization (Pr) and coercive field (Ec) are 12–19 μC cm−2 and 2,000–2,500 kV cm−1, respectively. The piezoelectric response of 1 μm thick films is investigated for 6%YO1.5–94% HfO2, 7%YO1.5–93%HfO2, and 5%YO1.5–95%(Hf0.50Zr0.50)O2 films, which have piezoelectric coefficients (d33) of 1.0, 3.3, and 5.0 pm V−1, respectively. These results show no‐heating deposition of x%YO1.5–(100−x%)(Hf1−yZry)O2 films with ferroelectric and piezoelectric properties.
- 25 June 2023
- Published by Wiley in Physica Status Solidi (a)
- Vol. 220 (14)
Open AccessNo‐Heating Deposition of Ferroelectric x%YO1.5–(100−x%)(Hf1−yZry)O2 Films
The no‐heating deposition of x%YO1.5–(100−x%)(Hf1−yZry)O2 (x = 0−0.09, y = 0, 0.25, 0.50, and 1) is achieved using a radio‐frequency magnetron sputtering method. To investigate the crystal structure and ferroelectric properties, epitaxial films are grown on (111)‐oriented indium tin oxide (ITO)/(111) Y‐stabilized zirconia (YSZ) substrates. The ferroelectric orthorhombic phase is obtained for the 5–7%YO1.5–95–93%HfO2 and 5%YO1.5–95% (Hf0.75Zr0.25)O2 films. The field‐induced phase transition from tetragonal to orthorhombic is confirmed for the 8%YO1.5–92%HfO2 and 5%YO1.5–95%(Hf0.50Zr0.50)O2 films. The remnant polarization (Pr) and coercive field (Ec) are 12–19 μC cm−2 and 2,000–2,500 kV cm−1, respectively. The piezoelectric response of 1 μm thick films is investigated for 6%YO1.5–94% HfO2, 7%YO1.5–93%HfO2, and 5%YO1.5–95%(Hf0.50Zr0.50)O2 films, which have piezoelectric coefficients (d33) of 1.0, 3.3, and 5.0 pm V−1, respectively. These results show no‐heating deposition of x%YO1.5–(100−x%)(Hf1−yZry)O2 films with ferroelectric and piezoelectric properties.
- 23 February 2023
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 5 (3) , 1600-1605
Systematic Investigation of Ferroelectric Properties in x%YO1.5–(100–x%)Hf1–yZryO2 Films
- 23 February 2023
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 5 (3) , 1600-1605
Systematic Investigation of Ferroelectric Properties in x%YO1.5–(100–x%)Hf1–yZryO2 Films
- Open Access
- 2 May 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 120 (18)
Exploring leakage in dielectric films via automated experiments in scanning probe microscopy
Electronic conduction pathways in dielectric thin films are explored using automated experiments in scanning probe microscopy (SPM). Here, we use large field of view scanning to identify the position of localized conductive spots and develop an SPM workflow to probe their dynamic behavior at higher spatial resolution as a function of time, voltage, and scanning process in an automated fashion. Using this approach, we observe the variable behaviors of the conductive spots in a 20-nm-thick ferroelectric Hf0.54Zr0.48O2 film, where conductive spots disappear and reappear during continuous scanning. There are also fresh conductive spots that develop during scanning. The automated workflow is universal and can be integrated into a wide range of microscopy techniques, including SPM, electron microscopy, optical microscopy, and chemical imaging.
- 2 May 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 120 (18)
Open AccessExploring leakage in dielectric films via automated experiments in scanning probe microscopy
Electronic conduction pathways in dielectric thin films are explored using automated experiments in scanning probe microscopy (SPM). Here, we use large field of view scanning to identify the position of localized conductive spots and develop an SPM workflow to probe their dynamic behavior at higher spatial resolution as a function of time, voltage, and scanning process in an automated fashion. Using this approach, we observe the variable behaviors of the conductive spots in a 20-nm-thick ferroelectric Hf0.54Zr0.48O2 film, where conductive spots disappear and reappear during continuous scanning. There are also fresh conductive spots that develop during scanning. The automated workflow is universal and can be integrated into a wide range of microscopy techniques, including SPM, electron microscopy, optical microscopy, and chemical imaging.
- 18 January 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 131 (3) , 035301
Domain structures induced by tensile thermal strain in epitaxial PbTiO3 films on silicon substrates
The fabrication of epitaxial ferroelectric materials on Si substrates is key to the design of superior ferroelectric devices for applications involving microelectromechanical systems (MEMS). The domain structures of epitaxial PbTiO3 films grown on Si substrates with an epitaxial SrTiO3 buffer layer were investigated, especially in terms of film thickness dependence. The low thermal expansion coefficient of Si was found to affect the volume fraction of (001)-oriented domains not only in relatively thick film regions but also in the thinner ones. Compared with the PbTiO3 films deposited on SrTiO3 substrates, (100)-oriented domains were observed in films as thin as 18 nm, notwithstanding the strong misfit strain induced by the substrate. Moreover, the saturated volume fraction of the (001)-oriented domain was smaller than that of PbTiO3 on SrTiO3. Thermal strain plays a critical role in determining domain structures and is, therefore, expected to govern the electric properties of films useful in MEMS devices.
- 18 January 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 131 (3) , 035301
Domain structures induced by tensile thermal strain in epitaxial PbTiO3 films on silicon substrates
The fabrication of epitaxial ferroelectric materials on Si substrates is key to the design of superior ferroelectric devices for applications involving microelectromechanical systems (MEMS). The domain structures of epitaxial PbTiO3 films grown on Si substrates with an epitaxial SrTiO3 buffer layer were investigated, especially in terms of film thickness dependence. The low thermal expansion coefficient of Si was found to affect the volume fraction of (001)-oriented domains not only in relatively thick film regions but also in the thinner ones. Compared with the PbTiO3 films deposited on SrTiO3 substrates, (100)-oriented domains were observed in films as thin as 18 nm, notwithstanding the strong misfit strain induced by the substrate. Moreover, the saturated volume fraction of the (001)-oriented domain was smaller than that of PbTiO3 on SrTiO3. Thermal strain plays a critical role in determining domain structures and is, therefore, expected to govern the electric properties of films useful in MEMS devices.
- 14 January 2022
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 16 (10) , 2100574
No‐Heating Deposition of 1‐μm‐Thick Y‐Doped HfO2 Ferroelectric Films with Good Ferroelectric and Piezoelectric Properties by Radio Frequency Magnetron Sputtering Method
Y‐doped HfO2 ferroelectric films of ≈1 μm thick are deposited without heating by a radio frequency magnetron sputtering method. {100}‐oriented epitaxial films with orthorhombic phase are grown on (100)ITO//(100)YSZ substrates without heating. Their crystal structure is almost unchanged after postheat treatment at 800 °C. Ferroelectricity is confirmed for the no‐heating‐deposited films by polarization−electric field (P−E) curves, and their remanent polarization (Pr) and coercive fields are 12 μC cm−2 and 1.5 MV cm−1, respectively. These values are also almost unchanged after the postheat treatment. However, the postheat‐treated films show a lower breakdown electric field compared to the as‐deposited films without heat treatment. Approximately 1 μm‐thick films are also prepared without heating on (111)ITO/(111)Pt/TiOx/SiO2/(100)Si and (111)Pt/TiOx/SiO2/(100)Si substrates. Almost pure orthorhombic/tetragonal phase is deposited on both substrates without heating. The Pr value of the film on the (111)ITO/(111)Pt/TiOx/SiO2/(100)Si substrate is about 1.5 times larger than that on the (111)Pt/TiOx/SiO2/(100)Si substrate due to the better crystallinity of the film lattice‐matched with the underlying ITO layer. The effective piezoelectric constant (d33,f) of the film deposited on the (111)ITO/(111)Pt/TiOx/SiO2/(100)Si substrate without heating is estimated to be 4 pm V−1. The present low process temperature leads us to expect novel applications, especially for low‐heat‐resistance applications.
- 14 January 2022
- Published by Wiley in Physica Status Solidi (RRL) – Rapid Research Letters
- Vol. 16 (10) , 2100574
No‐Heating Deposition of 1‐μm‐Thick Y‐Doped HfO2 Ferroelectric Films with Good Ferroelectric and Piezoelectric Properties by Radio Frequency Magnetron Sputtering Method
Y‐doped HfO2 ferroelectric films of ≈1 μm thick are deposited without heating by a radio frequency magnetron sputtering method. {100}‐oriented epitaxial films with orthorhombic phase are grown on (100)ITO//(100)YSZ substrates without heating. Their crystal structure is almost unchanged after postheat treatment at 800 °C. Ferroelectricity is confirmed for the no‐heating‐deposited films by polarization−electric field (P−E) curves, and their remanent polarization (Pr) and coercive fields are 12 μC cm−2 and 1.5 MV cm−1, respectively. These values are also almost unchanged after the postheat treatment. However, the postheat‐treated films show a lower breakdown electric field compared to the as‐deposited films without heat treatment. Approximately 1 μm‐thick films are also prepared without heating on (111)ITO/(111)Pt/TiOx/SiO2/(100)Si and (111)Pt/TiOx/SiO2/(100)Si substrates. Almost pure orthorhombic/tetragonal phase is deposited on both substrates without heating. The Pr value of the film on the (111)ITO/(111)Pt/TiOx/SiO2/(100)Si substrate is about 1.5 times larger than that on the (111)Pt/TiOx/SiO2/(100)Si substrate due to the better crystallinity of the film lattice‐matched with the underlying ITO layer. The effective piezoelectric constant (d33,f) of the film deposited on the (111)ITO/(111)Pt/TiOx/SiO2/(100)Si substrate without heating is estimated to be 4 pm V−1. The present low process temperature leads us to expect novel applications, especially for low‐heat‐resistance applications.