Jigang Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jigang Zhang has a total of 64 co-authors. Here are the top co-authors by number of shared publications:
- Zhehao Ma
School of Civil Engineering, Qingdao University of Technology, Qingdao 266520, China
3 shared publications Chi Gu
Qingdao First Municipal Engn Co Ltd, Qingdao 266000, Peoples R China
2 shared publicationsFeifei Liu
Qingdao Univ Technol, Sch Civil Engn, Qingdao 266520, Peoples R China
2 shared publicationsGuoliang Zhao
Qingdao First Municipal Engn Co Ltd, Qingdao 266000, Peoples R China
2 shared publicationsHanyu Song
China Shanghai Architectural Design & Res Inst Co, Shanghai 200062, Peoples R China
2 shared publicationsQianying Wang
College of Civil Engineering & Architecture, Qingdao Agricultural University, Qingdao, Shandong, China
2 shared publications
Latest Publications
- 23 January 2026
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 12 (3) , 1-14
Parameter Modifications of HJC Constitutive Model of Ultra-High-Strength Concrete and Projectile Penetration Behaviors of Its Reinforced Slab
- 23 January 2026
- Published by Springer Nature in Journal of Dynamic Behavior of Materials
- Vol. 12 (3) , 1-14
Parameter Modifications of HJC Constitutive Model of Ultra-High-Strength Concrete and Projectile Penetration Behaviors of Its Reinforced Slab
- Open Access
Welding Residual Stress and Deformation of T-Joints in Large Steel Structural Modules
To reduce the computational cost associated with traditional moving heat source methods, a segmented approach is proposed for simulating the welding process of T-joints in large-scale infrastructure steel modules. Firstly, the hole-drilling method was employed to measure the welding residual stresses in a 2400 mm T-joint. Subsequently, a three-dimensional finite element model was established in ABAQUS, and a user-defined subroutine for the segmented moving heat source was developed in Fortran to calculate the welding residual stresses. The numerical simulation results were compared with experimental data, showing high consistency and further validating the accuracy of the finite element model. Furthermore, the distribution patterns of residual stresses along the thickness direction and the effects of different welding sequences on temperature, stress, and deformation were investigated to optimize the welding sequence. The results indicated that the residual stresses along the weld seam exhibited a compressive–tensile–compressive distribution, with the maximum tensile stress reaching approximately 347 MPa. Additionally, the simulation results demonstrated that the double-ellipsoidal heat source method was computationally intensive and failed to provide accurate results for long weld seams, whereas the segmented moving heat source approach reduced the computation time to only 38 h. Moreover, different welding sequences had a significant impact on residual stresses and deformation. Through comprehensive analysis, it was found that Case 1 (sequential welding in the forward direction) achieved the best performance in minimizing welding residual stresses and deformation.
Open AccessWelding Residual Stress and Deformation of T-Joints in Large Steel Structural Modules
To reduce the computational cost associated with traditional moving heat source methods, a segmented approach is proposed for simulating the welding process of T-joints in large-scale infrastructure steel modules. Firstly, the hole-drilling method was employed to measure the welding residual stresses in a 2400 mm T-joint. Subsequently, a three-dimensional finite element model was established in ABAQUS, and a user-defined subroutine for the segmented moving heat source was developed in Fortran to calculate the welding residual stresses. The numerical simulation results were compared with experimental data, showing high consistency and further validating the accuracy of the finite element model. Furthermore, the distribution patterns of residual stresses along the thickness direction and the effects of different welding sequences on temperature, stress, and deformation were investigated to optimize the welding sequence. The results indicated that the residual stresses along the weld seam exhibited a compressive–tensile–compressive distribution, with the maximum tensile stress reaching approximately 347 MPa. Additionally, the simulation results demonstrated that the double-ellipsoidal heat source method was computationally intensive and failed to provide accurate results for long weld seams, whereas the segmented moving heat source approach reduced the computation time to only 38 h. Moreover, different welding sequences had a significant impact on residual stresses and deformation. Through comprehensive analysis, it was found that Case 1 (sequential welding in the forward direction) achieved the best performance in minimizing welding residual stresses and deformation.
- 30 March 2024
- Published by Elsevier in Ocean Engineering
- Vol. 302
Experimental study and finite element analysis on impact resistance of wind turbine steel truss foundation
- 30 March 2024
- Published by Elsevier in Ocean Engineering
- Vol. 302
Experimental study and finite element analysis on impact resistance of wind turbine steel truss foundation
- Open Access
- 1 February 2024
- Published by Scientific Scholar in Arabian Journal of Chemistry
- Vol. 17 (2) , 105516
Study on thermal conversion and detoxification mechanism of fluorine during co-combustion of meager coal and spent cathode carbon block
- 1 February 2024
- Published by Scientific Scholar in Arabian Journal of Chemistry
- Vol. 17 (2) , 105516
Open AccessStudy on thermal conversion and detoxification mechanism of fluorine during co-combustion of meager coal and spent cathode carbon block
- 3 January 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 84, 108462
Experimental and theoretical investigation on residual bearing capacity of CFDST-T joints after lateral impact
- 3 January 2024
- Published by Elsevier in Journal of Building Engineering
- Vol. 84, 108462
Experimental and theoretical investigation on residual bearing capacity of CFDST-T joints after lateral impact
- Open Access
- 17 November 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (22) , 12433
Prediction of Failure Modes of Steel Tube-Reinforced Concrete Shear Walls Using Blending Fusion Model Based on Generative Adversarial Networks Data Augmentation
The steel tube-reinforced concrete (STRC) shear wall plays an important role in the seismic design of high-rise building structures. Due to the synergistic collaboration between steel tubes and concrete, they effectively enhance the ductility and energy dissipation capacity of conventional shear walls. To identify vulnerable areas prone to brittle failure and optimize the design, it is essential to develop a rapid method for identifying the failure mode of STRC shear walls. In this study, a fast identification method of STCR shear wall failure modes based on a Blending fusion model with Generative Adversarial Network (GAN) augmented data is proposed. The GAN is employed to address the issue of inadequate experimental data by generating new samples. This method combines classification boosting (Catboost), Random Forest (RF), K-Nearest Neighbors (KNN), and Least Absolute Shrinkage and Selection Operator (LASSO) to establish the Blending-CRKL fusion model to improve the prediction accuracy of the failure mode of STRC shear walls. The results reveal a significant improvement in the prediction performance of KNN, Backpropagation Neural Network (BPNN), RF, Light Gradient Boosting Machine (LightGBM), Catboost, and Blending-CRKL models after augmenting the training set with GAN. On average, the accuracy increased by 13%, precision increased by 81%, recall increased by 48%, and F1 score increased by 67%. The proposed Blending-CRKL fusion model outperforms the tested KNN, BPNN, RF, LightGBM, and Catboost models, achieving an accuracy rate of 97% in predicting the failure mode of STRC shear walls. Additionally, the stability and robustness of the Blending-CRKL model were validated, while the important features and value ranges of different failure modes were analyzed. This study provides a reference for the rapid identification of the failure mode of STRC shear walls.
- 17 November 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (22) , 12433
Open AccessPrediction of Failure Modes of Steel Tube-Reinforced Concrete Shear Walls Using Blending Fusion Model Based on Generative Adversarial Networks Data Augmentation
The steel tube-reinforced concrete (STRC) shear wall plays an important role in the seismic design of high-rise building structures. Due to the synergistic collaboration between steel tubes and concrete, they effectively enhance the ductility and energy dissipation capacity of conventional shear walls. To identify vulnerable areas prone to brittle failure and optimize the design, it is essential to develop a rapid method for identifying the failure mode of STRC shear walls. In this study, a fast identification method of STCR shear wall failure modes based on a Blending fusion model with Generative Adversarial Network (GAN) augmented data is proposed. The GAN is employed to address the issue of inadequate experimental data by generating new samples. This method combines classification boosting (Catboost), Random Forest (RF), K-Nearest Neighbors (KNN), and Least Absolute Shrinkage and Selection Operator (LASSO) to establish the Blending-CRKL fusion model to improve the prediction accuracy of the failure mode of STRC shear walls. The results reveal a significant improvement in the prediction performance of KNN, Backpropagation Neural Network (BPNN), RF, Light Gradient Boosting Machine (LightGBM), Catboost, and Blending-CRKL models after augmenting the training set with GAN. On average, the accuracy increased by 13%, precision increased by 81%, recall increased by 48%, and F1 score increased by 67%. The proposed Blending-CRKL fusion model outperforms the tested KNN, BPNN, RF, LightGBM, and Catboost models, achieving an accuracy rate of 97% in predicting the failure mode of STRC shear walls. Additionally, the stability and robustness of the Blending-CRKL model were validated, while the important features and value ranges of different failure modes were analyzed. This study provides a reference for the rapid identification of the failure mode of STRC shear walls.
- Open Access
Study on the Impact Resistance of FRP Pasted onto a Blastproof Partition Wall under Out-of-Plane Repeated Impact Load
A blastproof partition wall in civil air defense engineering is easily subjected to out-of-plane impact loads, such as object impacts, and structural collapse in peacetime. In this study, the pendulum impact test was carried out for the first time on six blastproof partition walls pasted with fiber-reinforced polymer (FRP). Using a method combining finite element simulation and experimental research, the influence of parameters such as the FRP type, layer number and width, and pendulum impact number on the impact resistance of the wall was systematically studied. The test results show that pasting FRP on the back of the blastproof partition wall can significantly improve the impact resistance and reduce the damage degree of the concrete. The impact recovery coefficient increased from 0.33 to 0.57, but with the increase in the number of impacts, large-rupture-strain FRP (LRS-FRP) can give full play to the advantages of a large tensile fracture strain and cooperate with the wall to deform, and the selection of FRP with a large tensile fracture strain is the key to resisting multiple impact loads. Finally, the experimental basis and an economical and reliable protection method are provided for the study of improving the impact resistance of the blastproof partition wall.
Open AccessStudy on the Impact Resistance of FRP Pasted onto a Blastproof Partition Wall under Out-of-Plane Repeated Impact Load
A blastproof partition wall in civil air defense engineering is easily subjected to out-of-plane impact loads, such as object impacts, and structural collapse in peacetime. In this study, the pendulum impact test was carried out for the first time on six blastproof partition walls pasted with fiber-reinforced polymer (FRP). Using a method combining finite element simulation and experimental research, the influence of parameters such as the FRP type, layer number and width, and pendulum impact number on the impact resistance of the wall was systematically studied. The test results show that pasting FRP on the back of the blastproof partition wall can significantly improve the impact resistance and reduce the damage degree of the concrete. The impact recovery coefficient increased from 0.33 to 0.57, but with the increase in the number of impacts, large-rupture-strain FRP (LRS-FRP) can give full play to the advantages of a large tensile fracture strain and cooperate with the wall to deform, and the selection of FRP with a large tensile fracture strain is the key to resisting multiple impact loads. Finally, the experimental basis and an economical and reliable protection method are provided for the study of improving the impact resistance of the blastproof partition wall.
- Open Access
The Strength in Axial Compression of Aluminum Alloy Tube Confined Concrete Columns with a Circular Hollow Section: Experimental Results
Steel tube confined concrete (STCC) stub columns have great strength and facilitate construction. In this study, the axial compressive strength of an aluminum alloy tube confined concrete column with (ATCC-CHS) and without (ATCC) a circular hollow section was tested in laboratory experiments. The influence of concrete strength, diameter–thickness ratio and the hollow rate on the failure mode, ultimate compressive strength, strain, stiffness, constraint effects and ductility was quantified. The experiments showed that local buckling failure could be effectively delayed when the outer aluminum tube did not directly bear axial load. Columns without a circular hollow section had bearing capacities approximately 20% higher than those with a circular hollow section, though their ductility was poorer. The ultimate strength tended to increase with decreases in the hollow rate and diameter–thickness ratio. It tended to increase with increasing concrete strength, though stronger concrete also reduced ductility. The bearing capacities of the columns were calculated according to several proposed formulas and compared with the experimental results, and the proposed Teng and Attard’s formula appeared to be satisfactory.
Open AccessThe Strength in Axial Compression of Aluminum Alloy Tube Confined Concrete Columns with a Circular Hollow Section: Experimental Results
Steel tube confined concrete (STCC) stub columns have great strength and facilitate construction. In this study, the axial compressive strength of an aluminum alloy tube confined concrete column with (ATCC-CHS) and without (ATCC) a circular hollow section was tested in laboratory experiments. The influence of concrete strength, diameter–thickness ratio and the hollow rate on the failure mode, ultimate compressive strength, strain, stiffness, constraint effects and ductility was quantified. The experiments showed that local buckling failure could be effectively delayed when the outer aluminum tube did not directly bear axial load. Columns without a circular hollow section had bearing capacities approximately 20% higher than those with a circular hollow section, though their ductility was poorer. The ultimate strength tended to increase with decreases in the hollow rate and diameter–thickness ratio. It tended to increase with increasing concrete strength, though stronger concrete also reduced ductility. The bearing capacities of the columns were calculated according to several proposed formulas and compared with the experimental results, and the proposed Teng and Attard’s formula appeared to be satisfactory.
- Open Access
- 1 January 2022
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 29 (1) , 265-273
Theoretical analysis of aluminum honeycomb sandwich panel supported by reinforced concrete wall under low-speed impact load
Honeycomb materials are widely used across engineering fields. The use of honeycomb sandwich structures as energy dissipation and impact protection materials for reinforced concrete components in the field of civil engineering is a novel concept. Therefore, it is of great significance to study the energy absorption characteristics, dynamic response theoretical model, and collapse energy dissipation theory for the use of honeycomb sandwich structures as protective materials. Based on the large-scale low-speed pendulum impact test and the corresponding finite element model, this study establishes an ideal model for the honeycomb sandwich panel under the impact of a square flat head and gives the corresponding theoretical derivation. At the same time, it puts forward a method to estimate the energy consumption and dynamic crushing distance based on the energy consumption theory angle of the covering layer.
- 1 January 2022
- Published by Walter de Gruyter GmbH in Science and Engineering of Composite Materials
- Vol. 29 (1) , 265-273
Open AccessTheoretical analysis of aluminum honeycomb sandwich panel supported by reinforced concrete wall under low-speed impact load
Honeycomb materials are widely used across engineering fields. The use of honeycomb sandwich structures as energy dissipation and impact protection materials for reinforced concrete components in the field of civil engineering is a novel concept. Therefore, it is of great significance to study the energy absorption characteristics, dynamic response theoretical model, and collapse energy dissipation theory for the use of honeycomb sandwich structures as protective materials. Based on the large-scale low-speed pendulum impact test and the corresponding finite element model, this study establishes an ideal model for the honeycomb sandwich panel under the impact of a square flat head and gives the corresponding theoretical derivation. At the same time, it puts forward a method to estimate the energy consumption and dynamic crushing distance based on the energy consumption theory angle of the covering layer.
- 1 January 2022
- Published by Springer Nature in Strength of Materials
- Vol. 54 (1) , 33-40
Split Hopkinson Pressure Bar (SHPB) Test and Different Modeling Methods of Aluminum Honeycomb Materials
- 1 January 2022
- Published by Springer Nature in Strength of Materials
- Vol. 54 (1) , 33-40
Split Hopkinson Pressure Bar (SHPB) Test and Different Modeling Methods of Aluminum Honeycomb Materials