ABAdam Boháček

Adam Boháček

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Adam Boháček has a total of 6 co-authors. Here are the top co-authors by number of shared publications:

  • Michal Brandtner

    Brno University of Technology, Faculty of Civil Engineering, Veveří 331/95, 60200 Brno, Czech Republic

    2 shared publications
  • Ales Prucha

    Faculty of Civil Engineering, Brno University of Technology, Veveří 331/95, 602 00 Brno, Czech Republic

    1 shared publication
  • Barbora Nečasová

    Faculty of Civil Engineering, Brno University of Technology, Veveří 331/95, 602 00 Brno, Czech Republic

    1 shared publication
  • Jiri Slanhof

    Brno University of Technology, Faculty of Civil Engineering, Veveří 331/95, 60200 Brno, Czech Republic

    1 shared publication
  • Jiří Šlanhof

    Brno University of Technology, Faculty of Civil Engineering, Veveří 331/95, Brno 602 00, Czech Republic

    1 shared publication
  • Jiří Šlanhof

    Faculty of Civil Engineering, Brno University of Technology, Veveří 331/95, 602 00 Brno, Czech Republic

    1 shared publication

Latest Publications

  • Open Access

    Cohesion and adhesion of a sealant joint subjected to compressive stress

    by Adam Bohacek, Michal Brandtner, Jiri Slanhof

    This article is devoted to the evaluation of the suitability of the use of sealants when applied to a cement-based material and its subsequent exposure to compressive stress. Aquapanel cement board is chosen as the underlying material. In general, cementitious materials are characterized by a high concentration of dust particles on the surface, which prevent the correct adhesion of the sealant to the substrate, and therefore their sealing is often problematic. The sealants presented in this research are selected based on the manufacturer's recommendations for suitability for sealing cement-based materials. Base plates are made from cement board, which are subsequently sealed according to the procedures established by the ČSN EN ISO 11432 standard. The samples produced in this way are then cycled and their resistance to pressure stress is subsequently tested. The results of the test performed in this way are evaluated by measuring and visually evaluating the adhesion and cohesion of the cemented joint. Based on the results, it is possible to recommend all of the tested sealants for sealing cementitious base materials that are exposed to compressive stress.

  • Open Access

    Use of Bonded Joints for Fastening Sheet-Metal Components to Contemporary Facades Fitted with an External Thermal Insulation Composite System with Thin-Layer Acrylic Plaster

    by Jiří Šlanhof, Aleš Průcha, Barbora Nečasová, Adam Boháček

    This paper deals with the issue of fastening sheet-metal components on the facades of contemporary buildings that are massively insulated with external thermal insulation composite systems. This research focused on facades with thin-layer acrylic plaster and sheet-metal components made of aluminium, copper and hot-dipped galvanized sheet metal. Two different test methods and test sample geometries were used to determine the most critical aspects for the studied application sectors. Surprisingly high tensile properties as well as shear stresses in the bonded joints were recorded for all the selected combinations. The presented results confirmed the assumed benefits for the construction industry and the future practical use of this technology in construction, although the durability of a bonded joint will always depend mainly on the quality of the bonded substrate.


  • Determination of resistance of sealed joint to compression stress

    by Adam Boháček, Jiří Šlanhof, Michal Brandtner

    Mankind has been dealing with the issue of sealing since the very beginning of construction. Sealed joints are exposed to several external influences, whether physical or mechanical. These effects also include compressive stresses on the sealed joint. If we know that the structure in which the sealed joint will be placed will be exposed to compressive stress, we should choose a suitable sealant regarding this fact. A sealant suitable for sealing joints subjected to compressive stress should have sufficient flexibility after it has hardened. If the sealed joint is not flexible enough, its pressure load can significantly damage the sealed joint, and thus damage the entire structure. This article deals specifically with the sealing of problematic material. Aquapanel cement board is selected as a problematic material for the purposes of the presented research. The tested sealants are selected based on the manufacturer’s recommendations on the suitability of these sealants for sealing cementitious materials. Furthermore, primers are used, which are again selected according to the manufacturer’s recommendations. Test samples are made from selected materials, which are further conditioned according to a predetermined schedule. Then these samples are tested according to the European standard. Specifically, the resistance of a sealed joint subjected to compressive stress is tested. After exposing the test specimens to this stress, the sealed joints and their possible failure or deterioration are evaluated. The test results are recorded and further evaluated. Based on the evaluation of these results, it is possible to recommend all tested sealants for sealing cementitious materials, except acrylic sealant. The sealed joint made of acrylic sealant shows significant cracks in this test. These cracks are caused by the insufficient flexibility of this type of sealant and thanks to them the sealed joint is considerably degraded.

  • Open Access

    Properties of Selected Polyurethane Sealants in the Sealing of Cement-based Materials

    by Adam Boháček

    Since the rise of cement-based building elements, there has been a need to seal these materials. Therefore, this article deals with the sealing of cement-based materials, specifically glass cement. The aim of this work is to find a sealant for sealing this problematic substrate, to verify its suitability and to show that polyurethane sealants are also important in the construction market. The problem of a cement-based substrate lies mainly in the dustiness of its surface, where there are always small dust particles on its surface. The main method for testing these sealants is the tensile test, which checks both the properties of the sealant itself and the contact joint between the sealant and the base material. Tensile test specimens are made of glass-cement plates and three representatives of one-component flexible polyurethane sealants are selected as the sealing material. From the results of the tensile test, it can be concluded that, with the appropriate choice of sealant and primer, problematic cement-based materials with good results can be sealed, provided that the grinding is carried out correctly.