George Andrew Antonelli
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
George Andrew Antonelli has a total of 83 co-authors. Here are the top co-authors by number of shared publications:
Nicholas Keller
Onto Innovation Inc. (United States)
4 shared publicationsNick Keller
Onto Innovation Inc. (United States)
4 shared publicationsSubhadeep Kal
Tokyo Electron Technology Center, America, LLC 4 , 257 Fuller Road, Albany, New York 12203
4 shared publicationsAlain C. Diebold
State Univ. of New York at Albany (United States)
3 shared publicationsH. Sinha
University of Wisconsin-Madison Plasma Processing and Technology Laboratory and Department of Electrical and Computer Engineering Madison, Wisconsin 53706
3 shared publications- J. Leon Shohet
University of Wisconsin-Madison 1 Plasma Processing and Technology Laboratory and Department of Electrical and Computer Engineering Madison, Wisconsin 53706, USA
3 shared publications
Latest Publications
- Open Access
- 18 February 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (7)
Mid-infrared ellipsometry for optical critical dimension metrology
Mid-infrared ellipsometry offers a powerful approach for non-destructive optical critical dimension (OCD) metrology in advanced semiconductor manufacturing. This technique supports in-line measurements of high aspect ratio structures, such as those found in 3D NAND memory devices. The incorporation of quantum cascade lasers and fast phase modulation allows rapid acquisition of Mueller matrix elements with high spatial resolution and sub-Å precision. Material-specific absorption in the mid-infrared range allows depth-resolved profiling of device structures, overcoming the limitations of conventional OCD. Rigorous coupled wave analysis is used to extract structural parameters from the measured spectra. Agreement with destructive reference metrology has been demonstrated on a variety of structures. The ability to measure multiple Mueller elements further enhances characterization of complex geometries, making mid-infrared ellipsometry a valuable tool for process control in semiconductor fabrication.
- 18 February 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (7)
Open AccessMid-infrared ellipsometry for optical critical dimension metrology
Mid-infrared ellipsometry offers a powerful approach for non-destructive optical critical dimension (OCD) metrology in advanced semiconductor manufacturing. This technique supports in-line measurements of high aspect ratio structures, such as those found in 3D NAND memory devices. The incorporation of quantum cascade lasers and fast phase modulation allows rapid acquisition of Mueller matrix elements with high spatial resolution and sub-Å precision. Material-specific absorption in the mid-infrared range allows depth-resolved profiling of device structures, overcoming the limitations of conventional OCD. Rigorous coupled wave analysis is used to extract structural parameters from the measured spectra. Agreement with destructive reference metrology has been demonstrated on a variety of structures. The ability to measure multiple Mueller elements further enhances characterization of complex geometries, making mid-infrared ellipsometry a valuable tool for process control in semiconductor fabrication.
- Open Access
- 12 February 2026
- Published by Elsevier in SSRN Electronic Journal
Modal Analysis of Through-Silicon Vias via Rayleigh–Ritz Methods: A Foundation for Acoustic Non-Destructive Void Evaluation
This work develops a frequency-domain modeling framework based on the Rayleigh–Ritz variational method for analyzing the vibrational modes of through-silicon vias (TSVs). Voids formed during electrochemical copper deposition pose significant reliability risks and remain challenging to detect using conventional optical or destructive inspection techniques. By representing TSV geometries with tensor-product polynomial basis functions and applying a systematic symmetry-based mode classification, the proposed approach efficiently solves the elastic eigenvalue problem to obtain resonance frequencies and displacement fields across a wide range of geometries. Closed-form expressions for monomial volume moments are derived for spherical, conical, cylindrical, and composite voids, enabling rapid parametric evaluation of void-induced perturbations to the vibrational spectrum. Symmetry constraints imposed by photoacoustic and scanning acoustic microscopy excitation conditions reduce the accessible mode space, thereby improving computational tractability and enhancing experimental signal-to-noise ratio. Numerical studies demonstrate strong mode-specific sensitivity to void size and shape and reveal the dominant influence of geometric parameters—such as aspect ratio and radius—on modal dispersion. The results establish a rigorous theoretical basis for acoustic, non-destructive evaluation of TSV integrity and provide a foundation for advanced inspection, defect localization, and future inverse-modeling methodologies.
- 12 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessModal Analysis of Through-Silicon Vias via Rayleigh–Ritz Methods: A Foundation for Acoustic Non-Destructive Void Evaluation
This work develops a frequency-domain modeling framework based on the Rayleigh–Ritz variational method for analyzing the vibrational modes of through-silicon vias (TSVs). Voids formed during electrochemical copper deposition pose significant reliability risks and remain challenging to detect using conventional optical or destructive inspection techniques. By representing TSV geometries with tensor-product polynomial basis functions and applying a systematic symmetry-based mode classification, the proposed approach efficiently solves the elastic eigenvalue problem to obtain resonance frequencies and displacement fields across a wide range of geometries. Closed-form expressions for monomial volume moments are derived for spherical, conical, cylindrical, and composite voids, enabling rapid parametric evaluation of void-induced perturbations to the vibrational spectrum. Symmetry constraints imposed by photoacoustic and scanning acoustic microscopy excitation conditions reduce the accessible mode space, thereby improving computational tractability and enhancing experimental signal-to-noise ratio. Numerical studies demonstrate strong mode-specific sensitivity to void size and shape and reveal the dominant influence of geometric parameters—such as aspect ratio and radius—on modal dispersion. The results establish a rigorous theoretical basis for acoustic, non-destructive evaluation of TSV integrity and provide a foundation for advanced inspection, defect localization, and future inverse-modeling methodologies.
- Open Access
- 27 October 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (16)
Non-destructive lateral cavity etch measurements of 8-superlattice layer nanowire test structures using optical Mueller matrix spectroscopic ellipsometry, x-ray diffraction, and x-ray fluorescence
The semiconductor industry is expected to move to sub-3 nm nodes of gate all around complementary metal–oxide–semiconductor (complementary metal oxide semiconductor) transistor structures in the near future. This scaling is enabled, in part, by utilizing increased numbers of Si/Si1−xGex superlattice layers so that both n-MOS (metal–oxide–semiconductor) and p-MOS transistors come from the same film stack. A key manufacturing step is the selective Si1−xGex lateral cavity etch process. This cavity etch step selectively etches Si1−xGex exposed on the sidewall of the patterned film stack leaving the Si layers unetched, resulting in device structures that cannot be measured using a top-down scanning electron microscope. Accurate, non-destructive measurement is necessary to enable high volume manufacturing of gate all around devices. A set of 8-superlattice layer samples containing nanowire test structure targets were processed with varying amounts of cavity etch. Scatterometry done using Mueller matrix spectroscopic ellipsometry was used to determine the amount of cavity etch. However, it is not always possible to determine cavity etch when key sample attributes such as the film thickness of the superlattice vary across the wafer. A hybrid metrology approach was explored which combined three techniques for accurate measurements. High-resolution x-ray diffraction was used to determine layer thickness measurements, which were fed forward into a scatterometry structural model for a nanowire test structure. The scatterometry-determined cavity etch parameter was verified using x-ray fluorescence measurements of overall germanium volume loss. Transmission electron microscopy reference measurements were taken of lamellae prepared using focused ion beam milling of the sample.
- 27 October 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (16)
Open AccessNon-destructive lateral cavity etch measurements of 8-superlattice layer nanowire test structures using optical Mueller matrix spectroscopic ellipsometry, x-ray diffraction, and x-ray fluorescence
The semiconductor industry is expected to move to sub-3 nm nodes of gate all around complementary metal–oxide–semiconductor (complementary metal oxide semiconductor) transistor structures in the near future. This scaling is enabled, in part, by utilizing increased numbers of Si/Si1−xGex superlattice layers so that both n-MOS (metal–oxide–semiconductor) and p-MOS transistors come from the same film stack. A key manufacturing step is the selective Si1−xGex lateral cavity etch process. This cavity etch step selectively etches Si1−xGex exposed on the sidewall of the patterned film stack leaving the Si layers unetched, resulting in device structures that cannot be measured using a top-down scanning electron microscope. Accurate, non-destructive measurement is necessary to enable high volume manufacturing of gate all around devices. A set of 8-superlattice layer samples containing nanowire test structure targets were processed with varying amounts of cavity etch. Scatterometry done using Mueller matrix spectroscopic ellipsometry was used to determine the amount of cavity etch. However, it is not always possible to determine cavity etch when key sample attributes such as the film thickness of the superlattice vary across the wafer. A hybrid metrology approach was explored which combined three techniques for accurate measurements. High-resolution x-ray diffraction was used to determine layer thickness measurements, which were fed forward into a scatterometry structural model for a nanowire test structure. The scatterometry-determined cavity etch parameter was verified using x-ray fluorescence measurements of overall germanium volume loss. Transmission electron microscopy reference measurements were taken of lamellae prepared using focused ion beam milling of the sample.
- 16 September 2025
- Published by SPIE-Intl Soc Optical Eng
- Vol. 13606, 136060A
Deep learning outperforms RCWA for multimodal measurement of high-aspect-ratio nanostructures
Measuring performance-critical parameters in nanostructures is essential for optimizing optics. Our previous work replaced rigorous coupled-wave analysis (RCWA) with a multi-layer perceptron (MLP) that replicated RCWA Mueller matrix spectroscopic ellipsometry (MMSE), enabling gradient-based fitting at inference. While this measured tilt well, it was restricted to a 2D geometry and validated only for critical angle transmission (CAT) bar tilt. We later extended it to a 3D model for multiple parameters, achieving an R² of 0.88 compared ground truth. Still, the MLP approach required separate models for each parameter, and each inference took about 5 seconds. We propose a self-supervised pipeline that directly maps MMSE spectra to parameters, combining a variational autoencoder (VAE) and a convolutional neural network (CNN) with skip-connections. We pre-train the VAE on experimental MMSE spectra to learn a latent space. We then feed the encoder output and original spectra into the CNN, using SAXS and edge-detection outputs as labels, self-supervised with synthetic fits. Our approach achieves an R² of 0.94 for both tilt and profile prediction and reduces inference to under one second.
- 16 September 2025
- Published by SPIE-Intl Soc Optical Eng
- Vol. 13606, 136060A
Deep learning outperforms RCWA for multimodal measurement of high-aspect-ratio nanostructures
Measuring performance-critical parameters in nanostructures is essential for optimizing optics. Our previous work replaced rigorous coupled-wave analysis (RCWA) with a multi-layer perceptron (MLP) that replicated RCWA Mueller matrix spectroscopic ellipsometry (MMSE), enabling gradient-based fitting at inference. While this measured tilt well, it was restricted to a 2D geometry and validated only for critical angle transmission (CAT) bar tilt. We later extended it to a 3D model for multiple parameters, achieving an R² of 0.88 compared ground truth. Still, the MLP approach required separate models for each parameter, and each inference took about 5 seconds. We propose a self-supervised pipeline that directly maps MMSE spectra to parameters, combining a variational autoencoder (VAE) and a convolutional neural network (CNN) with skip-connections. We pre-train the VAE on experimental MMSE spectra to learn a latent space. We then feed the encoder output and original spectra into the CNN, using SAXS and edge-detection outputs as labels, self-supervised with synthetic fits. Our approach achieves an R² of 0.94 for both tilt and profile prediction and reduces inference to under one second.
- 5 May 2025
- Published by SPIE-Intl Soc Optical Eng
- Vol. 13426, 228-239
Hybrid metrology for non-destructive lateral cavity etch measurements of 8-superlattice layer nanowire test structures (NWTS) using optical Mueller matrix spectroscopic ellipsometry (MMSE), x-ray diffraction (XRD), and x-ray reflectivity (XRR)
Lateral gate-all around (LGAA) transistor structures are on the IEEE IRDS logic roadmap for sub-3 nm nodes, with scaling being enabled in part by utilizing increased numbers of Si/Si(1-x)Ge(x) superlattice layers to form the structures. A key manufacturing step is the lateral cavity etch process, which is required for the indent etch and gate release steps. After anisotropic etch through the superlattice, the cavity etch step selectively etches the Si(1-x)Ge(x) layers, resulting in device geometries that are cannot be measured with traditional top-down scanning electron microscope (CDSEM) critical dimension metrology. Accurate, non-destructive metrology is necessary to enable high volume manufacturing of LGAA devices. A set of 8-superlattice layer samples containing nanowire test structure (NWTS) targets were processed at three levels of cavity etch. A hybrid metrology approach was explored which combined three techniques for accurate measurements. High-resolution X-ray Diffraction (HRXRD) determined individual layer thickness measurements, which were fed forward into an Optical Critical dimension (OCD) model for a nanowire test structure (NWTS). The OCD-determined cavity etch parameter was verified using X-ray Fluorescence (XRF) measurements of overall germanium volume. Transmission electron microscope (TEM) reference measurements were taken of lamellae prepared using focused ion beam (FIB) milling of the sample. The destructive TEM measurements were used as a reference to determine the accuracy of the non-destructive hybrid metrology. Sub-nanometer matching to STEM was achieved with the nondestructive hybrid XRD/OCD and XRF feed forward method.
- 5 May 2025
- Published by SPIE-Intl Soc Optical Eng
- Vol. 13426, 228-239
Hybrid metrology for non-destructive lateral cavity etch measurements of 8-superlattice layer nanowire test structures (NWTS) using optical Mueller matrix spectroscopic ellipsometry (MMSE), x-ray diffraction (XRD), and x-ray reflectivity (XRR)
Lateral gate-all around (LGAA) transistor structures are on the IEEE IRDS logic roadmap for sub-3 nm nodes, with scaling being enabled in part by utilizing increased numbers of Si/Si(1-x)Ge(x) superlattice layers to form the structures. A key manufacturing step is the lateral cavity etch process, which is required for the indent etch and gate release steps. After anisotropic etch through the superlattice, the cavity etch step selectively etches the Si(1-x)Ge(x) layers, resulting in device geometries that are cannot be measured with traditional top-down scanning electron microscope (CDSEM) critical dimension metrology. Accurate, non-destructive metrology is necessary to enable high volume manufacturing of LGAA devices. A set of 8-superlattice layer samples containing nanowire test structure (NWTS) targets were processed at three levels of cavity etch. A hybrid metrology approach was explored which combined three techniques for accurate measurements. High-resolution X-ray Diffraction (HRXRD) determined individual layer thickness measurements, which were fed forward into an Optical Critical dimension (OCD) model for a nanowire test structure (NWTS). The OCD-determined cavity etch parameter was verified using X-ray Fluorescence (XRF) measurements of overall germanium volume. Transmission electron microscope (TEM) reference measurements were taken of lamellae prepared using focused ion beam (FIB) milling of the sample. The destructive TEM measurements were used as a reference to determine the accuracy of the non-destructive hybrid metrology. Sub-nanometer matching to STEM was achieved with the nondestructive hybrid XRD/OCD and XRF feed forward method.
- Open Access
- 1 January 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 43 (1)
Machine learning driven measurement of high-aspect-ratio nanostructures using Mueller matrix spectroscopic ellipsometry
Accurate fabrication of high-aspect ratio (HAR) structures in applications from semiconductor devices to x-ray observatories is essential for their optimal performance because their performance directly depends on their structure. High-efficiency critical-angle transmission (CAT) gratings enable high-resolution x-ray spectroscopy in astrophysics, but their performance is only ideal when certain performance-critical parameters, like the bar tilts introduced during deep reactive-ion etching, are tuned to precise values. Traditional measurement methods like small-angle x-ray scattering (SAXS) are accurate, but limit the development of robust control algorithms to nudge performance-critical parameters toward favorable values because they are slow and often destructive. We present a fast, accurate, nondestructive measurement method using Mueller matrix spectroscopic ellipsometry and machine learning. Given a HAR structure, we train on rigorous coupled-wave analysis simulation data to predict Mueller matrix spectra from input performance-critical parameter values. We then invert this forward problem by freezing our network weights, measuring experimental Mueller matrix spectra, and vanilla gradient descending on performance-critical parameters to values that correspond to the input Mueller matrix spectra. Introducing machine learning to invert the forward problem reduces computation time, and experimental results demonstrate close agreement between our method’s determined tilt and SAXS measurements. Our accurate, fast measurement method paves the way for the development of robust control algorithms that adjust fabrication parameters in response to measurement, ensuring optimal performance in not only CAT gratings but also HAR structures embedded in applications from semiconductor to microelectromechanical systems fabrication.
- 1 January 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 43 (1)
Open AccessMachine learning driven measurement of high-aspect-ratio nanostructures using Mueller matrix spectroscopic ellipsometry
Accurate fabrication of high-aspect ratio (HAR) structures in applications from semiconductor devices to x-ray observatories is essential for their optimal performance because their performance directly depends on their structure. High-efficiency critical-angle transmission (CAT) gratings enable high-resolution x-ray spectroscopy in astrophysics, but their performance is only ideal when certain performance-critical parameters, like the bar tilts introduced during deep reactive-ion etching, are tuned to precise values. Traditional measurement methods like small-angle x-ray scattering (SAXS) are accurate, but limit the development of robust control algorithms to nudge performance-critical parameters toward favorable values because they are slow and often destructive. We present a fast, accurate, nondestructive measurement method using Mueller matrix spectroscopic ellipsometry and machine learning. Given a HAR structure, we train on rigorous coupled-wave analysis simulation data to predict Mueller matrix spectra from input performance-critical parameter values. We then invert this forward problem by freezing our network weights, measuring experimental Mueller matrix spectra, and vanilla gradient descending on performance-critical parameters to values that correspond to the input Mueller matrix spectra. Introducing machine learning to invert the forward problem reduces computation time, and experimental results demonstrate close agreement between our method’s determined tilt and SAXS measurements. Our accurate, fast measurement method paves the way for the development of robust control algorithms that adjust fabrication parameters in response to measurement, ensuring optimal performance in not only CAT gratings but also HAR structures embedded in applications from semiconductor to microelectromechanical systems fabrication.
- Open Access
- 1 October 2024
- Published by SPIE-Intl Soc Optical Eng in Journal of Micro/Nanopatterning, Materials, and Metrology
- Vol. 23 (04) , 044004-26
Superlattice effects and limitations of non-destructive measurement of advanced Si/Si1−xGex superlattice structures using Mueller matrix scatterometry and high-resolution X-ray diffraction
Non-destructive metrology is critical to enabling process control for current and next-generation three-dimensional (3D) transistor and memory structures.1 3D structures have become necessary due to scaling and performance requirements at advanced process nodes.2,3 Here, we discuss optical scatterometry and X-ray metrology for 3D nanosheet/nanowire (NS/NW) transistors with vertically stacked channels, which are fabricated using selective etching of the silicon–germanium
- 1 October 2024
- Published by SPIE-Intl Soc Optical Eng in Journal of Micro/Nanopatterning, Materials, and Metrology
- Vol. 23 (04) , 044004-26
Open AccessSuperlattice effects and limitations of non-destructive measurement of advanced Si/Si1−xGex superlattice structures using Mueller matrix scatterometry and high-resolution X-ray diffraction
Non-destructive metrology is critical to enabling process control for current and next-generation three-dimensional (3D) transistor and memory structures.1 3D structures have become necessary due to scaling and performance requirements at advanced process nodes.2,3 Here, we discuss optical scatterometry and X-ray metrology for 3D nanosheet/nanowire (NS/NW) transistors with vertically stacked channels, which are fabricated using selective etching of the silicon–germanium
- 10 April 2024
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12955, 18-107
Superlattice effects and limitations of non-destructive measurement of advanced Si/Si(1-x)Ge(x) superlattice structures using Mueller matrix scatterometry (MMSE) and high-resolution x-ray diffraction (XRD)
Advanced semiconductor devices are moving toward 3D geometries due to scaling demands and performance requirements. The non-destructive metrology necessary for process control for high volume manufacturing of 3D structures must be advanced to facilitate their transition from technology development to high volume manufacturing. Optical Critical Dimensions (OCD) techniques based on Mueller Matrix Scatterometry (MMSE) as well as XxRay Diffraction (XRD) have proved capable of measuring the Si/Si1-xGex few layer superlattices used to fabricate Gate All Around (GAA) transistor device test structures. The limitations of these techniques associated with superlattice device structures needed to be further understood. To understand the limits of MMSE Scatterometry and XRD, a four superlattice layer Si/Si1-xGex structure was measured as a film stack, a column etched sample, and at two levels of cavity etch. XRD was used to determine individual layer thicknesses and compositions of the film stack, and electron microscope data was used to verify initial structure dimensions for OCD models. First, film stack characterization and metrology for both ellipsometry and x-ray characterization were explored. OCD modeling and measurement strategies were evaluated to address the challenge of fitting the superlattice thicknesses in the stack at different etch levels. We demonstrate the characterization of relevant test structure dimensions, including cavity etch using MMSE-Scatterometry. We also demonstrate an alternate technique, x-ray fluorescence for determining cavity etch on the same structures.
- 10 April 2024
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12955, 18-107
Superlattice effects and limitations of non-destructive measurement of advanced Si/Si(1-x)Ge(x) superlattice structures using Mueller matrix scatterometry (MMSE) and high-resolution x-ray diffraction (XRD)
Advanced semiconductor devices are moving toward 3D geometries due to scaling demands and performance requirements. The non-destructive metrology necessary for process control for high volume manufacturing of 3D structures must be advanced to facilitate their transition from technology development to high volume manufacturing. Optical Critical Dimensions (OCD) techniques based on Mueller Matrix Scatterometry (MMSE) as well as XxRay Diffraction (XRD) have proved capable of measuring the Si/Si1-xGex few layer superlattices used to fabricate Gate All Around (GAA) transistor device test structures. The limitations of these techniques associated with superlattice device structures needed to be further understood. To understand the limits of MMSE Scatterometry and XRD, a four superlattice layer Si/Si1-xGex structure was measured as a film stack, a column etched sample, and at two levels of cavity etch. XRD was used to determine individual layer thicknesses and compositions of the film stack, and electron microscope data was used to verify initial structure dimensions for OCD models. First, film stack characterization and metrology for both ellipsometry and x-ray characterization were explored. OCD modeling and measurement strategies were evaluated to address the challenge of fitting the superlattice thicknesses in the stack at different etch levels. We demonstrate the characterization of relevant test structure dimensions, including cavity etch using MMSE-Scatterometry. We also demonstrate an alternate technique, x-ray fluorescence for determining cavity etch on the same structures.
- 10 April 2024
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12955, 118-265
Non-destructive measurement of bottom width in deep trench isolation structures using IRCD metrology
As scaling in semiconductor devices continues, the aspect ratios of deep trench isolation (DTI) structures have increased. DTI structures are used in power devices, power management ICs and image sensors as a method to isolate active devices by reducing crosstalk, parasitic capacitance, latch-up and allowing for an increase breakdown voltage of active devices. Measurement of these structures in high volume manufacturing (HVM), with non-destructive technology, has mostly been limited to the depth and top width of the DTI structure, while the bottom width (BCD) has not been able to be reliably measured. Here we present two different optical metrologies, “conventional” OCD and IRCD, that operate in the UV-VIS-NIR and MIR region of the electromagnetic spectrum, respectively, and discuss the measurability of DTI sidewall profile, bottom width, and depth in BCD (Bipolar CMOS DMOS) power management IC devices for each method at various pitches and line to space ratios. Experimental data will be presented showing sensitivity and discrimination of IRCD to a DOE specifically on the bottom width for three different structures.
- 10 April 2024
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12955, 118-265
Non-destructive measurement of bottom width in deep trench isolation structures using IRCD metrology
As scaling in semiconductor devices continues, the aspect ratios of deep trench isolation (DTI) structures have increased. DTI structures are used in power devices, power management ICs and image sensors as a method to isolate active devices by reducing crosstalk, parasitic capacitance, latch-up and allowing for an increase breakdown voltage of active devices. Measurement of these structures in high volume manufacturing (HVM), with non-destructive technology, has mostly been limited to the depth and top width of the DTI structure, while the bottom width (BCD) has not been able to be reliably measured. Here we present two different optical metrologies, “conventional” OCD and IRCD, that operate in the UV-VIS-NIR and MIR region of the electromagnetic spectrum, respectively, and discuss the measurability of DTI sidewall profile, bottom width, and depth in BCD (Bipolar CMOS DMOS) power management IC devices for each method at various pitches and line to space ratios. Experimental data will be presented showing sensitivity and discrimination of IRCD to a DOE specifically on the bottom width for three different structures.
- 10 April 2024
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12955, 129550Z
Metrology challenges for fabrication of high aspect ratio, nano scale x-ray diffraction gratings
Next-generation space telescopes under development by NASA will require high efficiency and resolving power soft x-ray spectrometers which can provide an order of magnitude increased performance compared to present space instrumentation. For the past decade the MIT Space Nanotechnology Lab has developed new x-ray spectrometer concepts based on so-called critical-angle transmission (CAT) gratings which exploit the principle of efficient x-ray reflection below the critical angle for total external reflection. These devices require challenging high-aspect ratio (HAR) “nano mirror” grating patterns with well controlled bar tilt angle and sub-nm surface smoothness. Gratings are patterned with precision (110) SOI wafers using 193 nm lithography and etched using a Bosch process. In this paper we present the first results of applying Mueller Matrix OCD mapping to our silicon HAR device geometry and compare with small angle x-ray scattering results.
- 10 April 2024
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12955, 129550Z
Metrology challenges for fabrication of high aspect ratio, nano scale x-ray diffraction gratings
Next-generation space telescopes under development by NASA will require high efficiency and resolving power soft x-ray spectrometers which can provide an order of magnitude increased performance compared to present space instrumentation. For the past decade the MIT Space Nanotechnology Lab has developed new x-ray spectrometer concepts based on so-called critical-angle transmission (CAT) gratings which exploit the principle of efficient x-ray reflection below the critical angle for total external reflection. These devices require challenging high-aspect ratio (HAR) “nano mirror” grating patterns with well controlled bar tilt angle and sub-nm surface smoothness. Gratings are patterned with precision (110) SOI wafers using 193 nm lithography and etched using a Bosch process. In this paper we present the first results of applying Mueller Matrix OCD mapping to our silicon HAR device geometry and compare with small angle x-ray scattering results.