AIArtem Iatsenko

Artem Iatsenko

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Artem Iatsenko has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Structure and properties of biogenic hydroxyapatite bioceramics modified by graphene-like structures

    by A. Iatsenko, O. Sych, A. Synytsia, P. Zaremba, S. Zahorodnia, A. Nikolenko, T. Tomila, O. Bykov

    Today bone tissue engineering is one of the most used technologies for treat bones injure. Materials containing hydroxyapatite and graphene have received much attention recently. The aim of this study was preparation of biogenic hydroxyapatite bioceramics modified by graphene-like structures investigation effect of graphene on the structure and properties of material. Biogenic hydroxyapatite bioceramics modified by graphene-like structures were successfully prepared by chemical vapor deposition (CVD) method. Subsequently, microstructure, composition, specific surface area, skeleton density, resorption rate in physiological solution and cytotoxicity were evaluated. XRD, IR spectroscopy, micro-Raman spectroscopy and SEM proved graphene oxide’s formation on biogenic hydroxyapatite as well as on silica single crystal for comparison. Although the coating of graphene-like structures on biogenic hydroxyapatite bioceramics reduces the specific surface area, it allows to 4 times increase resorption rate of biogenic hydroxyapatite bioceramics in physiological solution and does not affect the overall assessment of the cytotoxicity. MTT assay established non-cytotoxic effect and indicated a high potential of biogenic hydroxyapatite bioceramics modified by graphene-like structures using CVD method for medical application.


  • Open Access

    Development of improved technology for producing graphene-like coating by LPCVD method

    by Artem Iatsenko

    The object of research in this work was the coating of oxygraphene on a silicon single crystal substrate. In the work, the LPСVD (Low Pressure Chemical Vapor Deposition) method of deposition from the gas phase at low pressure is used to obtain graphene-like coatings on heat-resistant materials. A feature of the proposed LPCVD method in comparison with the classical method of deposition from the gas phase CVD (Chemical Vapor Deposition) by the method of catalytic decomposition of carbon-containing gas followed by the deposition of a graphene-like coating on a copper template is the use of a higher partial gas pressure, which leads to the deposition of graphene-like waste not only on the surface of the copper template-catalyst, but also in the entire volume of the reaction chamber and the materials introduced into it. A monocrystalline silicon template was used as a model for coating. The resulting coatings of different thicknesses were examined by scanning electron microscopy, Raman spectroscopy, and density was assessed by helium pycnometry. Based on the analysis of the results obtained using the method of scanning electron microscopy, the possibility of varying the thickness of the oxygraphene coating was shown. In addition, the formation of oxygraphene on a silicon single crystal substrate was confirmed by the Raman spectroscopy method, namely the presence of characteristic peaks in the spectra of the studied materials. Using the helium pycnometry method, a decrease in the density of the coated material from 2.25 g/cm3 to 2.08 g/cm3 was found. It was established that the greater the coating thickness, the lower the density. The general analysis showed that the developed LPСVD technology allows obtaining an oxygraphene coating on materials of any shape, porosity, size and resistant to temperatures above 600 °С in order to functionalize their surface and improve and improve their properties.


  • Effect of type and parameters of synthesis on the properties of magnetite nanoparticles

    by A. Synytsia, O. Sych, A. Iatsenko, T. Babutina, T. Tomila, O. Bykov, O. Olifan, T. Lobunets, A. Perekos, N. Boshytska


  • Open Access

    Effect of sintering temperature on structure and properties of highly porous glass-ceramics

    by Artem Iatsenko, Olena Sych, Tamara Tomila

    Highly porous biomaterials with a structure close to that of cancellous bone have been prepared using biogenic hydroxyapatite and glass of the SiO2-Na2O-CaO system by a replication of the polymer template structure. It has been established that during sintering of the samples the hydroxyapatite decomposes, which involves the formation of glass-ceramics containing phases of renanit NaCaPO4, calcium phosphate silicate Ca5(PO4)2SiO4, calcium pyrophosphate Ca2P2O7 and impurities of hydroxyapatite Ca5(PO4)3(OH). Structural characteristics and mechanical properties of the obtained materials are promising for the replacement of defective cancellous bone.