Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Biljana Maljković has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Evaluating AI-Based Video Analytics for Traffic Engineering: Accuracy, Calibration, and Practical Use

    by Dražen Cvitanić, Biljana Maljković, Sanja Vrdoljak

    This paper examines the potential and reliability of AI-based video analytics for solving key traffic engineering problems. The objectives were to compare several commercially available tools for collecting traffic data and, through practical examples, to show that AI-processed data can be used for the development, calibration, and validation of traffic models. Four AI-based video analytics (StreetLogic Pro, DataFromSky, CVEDIA RT Studio, and Camlytics Single) were tested using field video recordings at a signalized intersection on an urban arterial in Split, Croatia. Detection accuracy, usability, and sensitivity to camera placement and recording conditions are analyzed, and selected microscopic parameters (saturation flow rate and control delay) were obtained and compared with values derived from HCM procedures. DataFromSky and CVEDIA RT Studio achieved 97–99% vehicle detection accuracy and provided detailed trajectory data suitable for scientific applications, while StreetLogic Pro achieved 100% accuracy for operational vehicle counting. AI-based estimates of saturation flow rate and control delay differed by less than 1% and 5%, respectively, from traditional field measurements. The main novelty of this research lies in its practical comparison of AI-based video analytics tools combined with a worked example of using AI-derived data to calibrate analytical models, providing practical guidance for researchers and practitioners in traffic engineering.

  • Open Access

    Simulation-Based Modeling of the Impact of Left-Turn Bay Overflow on Signalized Intersection Capacity

    by Deana Breški, Biljana Maljković

    The motorized vehicle methodology in the Highway Capacity Manual (HCM) does not account for the effect of left-turn bay overflow, which is stated as a limitation of the methodology. In this study, an adjustment factor was developed to quantify the impact of left-turn bay length on the through lane capacity at signalized intersections. The adjustment factor was modeled based on a large number of scenarios generated using the CORSIM microsimulation model. These scenarios covered intersection geometries typical for two-phase signal control and included a wide range of traffic parameters (number of lanes, traffic volume, left-turn volume, left-turn bay length, cycle length, and green ratio). By comparing the capacity values obtained with a short left-turn bay to those with an infinitely long bay under identical other traffic conditions, it was possible to develop an adjustment factor that reflects the impact of turn bay overflow. A regression-based model was created and validated, showing very good agreement with the simulated values. The new adjustment factor provides an enhancement of the HCM estimation methodology that improves the accuracy of capacity and delay estimates in intersection evaluations as well as supports more effective intersection design and sustainable mobility. More accurate capacity estimation reduces congestion, travel delays, and vehicle stopping, directly contributing to sustainable transportation goals, lowering emissions, and supporting environmentally responsible urban mobility systems.


  • Open Access

    Green Infrastructure’s Role in Climate Change Adaptation: Summarizing the Existing Research in the Most Benefited Policy Sectors

    by Ana Kadić, Biljana Maljković, Katarina Rogulj, Jelena Kilić Pamuković

    Extreme climate change is today’s world’s most pressing and challenging problem. Increases in greenhouse gas emissions, the warming of the atmosphere and ocean, increased precipitation, rising sea levels, and temperature rise are the major effects of climate change that significantly affect urban infrastructure. Green Infrastructure (GI) is an increasingly acknowledged tool for climate change adaptation that contributes to sustainable urban and rural development. This study reviewed 111 research articles to identify and summarize the research findings about the role of GI in climate change adaptation. Furthermore, the research articles are grouped into three sectors with the most benefits of green infrastructure in climate change adaptation: mitigating urban heat islands, increasing ecosystem resilience, and flood risk management. The literature was further divided according to the developed or utilized strategies and techniques. The findings suggest that the topic of GI’s role in climate change adaptation is very current and it has been studied frequently in the last five years.


  • Open Access

    Trip Generation Models for Transportation Impact Analyses of Shopping Centers in Croatia

    by Deana Breški, Biljana Maljković, Mihaela Senjak

    For effective transportation planning, land use, travel behavior, and infrastructure capacity should be optimized to support sustainable urban growth and reduce congestion. Every new site development generates traffic volume, which can affect the quality of traffic flow in the surrounding road network. Therefore, trip generation, which predicts future travel demand, is a crucial step in the traditional four-step transportation model. In this context, the main objective of this study is to develop a model for estimating vehicle trip generation due to the construction of a shopping center, which is a significant traffic generator. The survey was conducted in Split (Croatia) at five existing locations, and linear regression analysis was used to develop models for different time periods. The results indicated that vehicle trips are strongly correlated with the gross floor area of shopping centers, with a high coefficient of determination. Additionally, this study presents a comparison of measured traffic volumes with estimates using ITE Trip Generation Manual equations. The findings suggest that these vehicle trip estimates should be reduced by approximately 40%. Since no previous studies have been conducted on the impact of land use on trip generation in the Republic of Croatia, the developed models represent a first step in creating a database that should be expanded with new data. Estimating the traffic generated by a new site development is a crucial component of traffic management, as it helps planners and engineers assess its impact on the surrounding road network and implement necessary measures to ensure efficient and safe traffic flow.


  • Open Access

    Analysis of cycling infrastructure - a case study of Split

    by Deana Breški, Biljana Maljković, Martin Matić

    Many cities in the world have recognized cycling as one of the alternative ways of urban transport and are increasingly investing in the development of cycling and appropriate infrastructure, which helps to ensure the sustainable development of both the city and mobility in general. Cycling has numerous advantages compared to motorized transport because it contributes to a healthier lifestyle, reduces the use of personal vehicles and thus the traffic volumes, and affects the reduction of fuel consumption and air pollution. Adequate cycling infrastructure and its connections to other modes of transportation are necessary for cycling to be both safe and attractive to the general public. The city of Split started investing in bicycle lanes and promoting this mode of transportation only in the last fifteen years. This paper presents an analysis of the existing bicycle infrastructure in the city area in terms of construction and network connectivity, as well as the compliance of geometric elements with the current Rulebook on Bicycle Infrastructure. Furthermore, the method of organization and use of the public bicycle system is presented. This system which was introduced in July 2019 and was upgraded in the following years, significantly contributed to the development of bicycle traffic in Split. Following the analysis, some recommendations for enhancing the cycling infrastructure were made. In general, urban planning and design of city roads and public areas can have a substantial impact on the safety, comfort and connectivity of the cycling infrastructure, which will help promote and develop cycling and sustainable mobility.

  • Open Access

    Application of the IHSDM for analysis of road design consistency and assessment of the number and type of traffic accidents: a case study of the Croatian state road DC1

    by Biljana Maljković, Dražen Cvitanić, Deana Breški

    Generally, statistical data show that more than 50% of fatal traffic accidents occur on rural two-lane roads, with over half being related to horizontal curves. Accident locations indicate that road alignment consistency has a significant impact on accident occurrence. Many crash prediction models and road design consistency models have been developed, mostly based on operating speed and road geometric characteristics. In this paper, the Interactive Highway Safety Design Model (IHSDM) was used to analyse the consistency of road horizontal and vertical elements, as well as to predict the number and type of crashes on a section of the state road DC1 from Vrlika to Hrvace, covering a length of approximately 24 km. Two modules within the software were utilized: the module for predicting the number and types of accidents (Crash Prediction Module - CPM) and the consistency of the road alignment module (Design Consistency Module - DCM). In this regard, two types of road alignment consistency analyses were conducted: one according to the Croatian road design guidelines and another using the IHSDM tool. Furthermore, a comparison between the estimated and actual number of accidents was performed. The comparison showed that the number of accidents predicted by the IHSDM software does not deviate significantly from the actual number of traffic accidents on the analysed section. Based on the results of the conducted analyses, locations along the road section with reduced safety were identified, and infrastructure measures were proposed to improve traffic safety, specifically in terms of reducing the number of accidents.

  • Improved Horizontal Curve Design Consistency Approach Using Steady-State Bicycle Model Combined with Realistic Speeds and Path Radii

    by Biljana Maljković, Dražen Cvitanić

    Three safety concerns have been identified in the conventional design consistency assessment procedure for horizontal curves: approximation of the vehicle by the point-mass model, use of unrealistic speeds, and the assumption that the path radius is equal to the design curve radius. This study presents a novel approach to the consistency assessment of horizontal curves in terms of vehicle stability (represented as the safety margin). The novel approach involves calculating the safety margins using the steady-state bicycle model to account for the nonuniform distribution of friction among individual axles due to grade and speed changes and using more-realistic driver behavior parameters. In this study, the realistic driver behavior parameters refer to the modeled operating speeds and calculated vehicle path radii, which were defined based on naturalistic driving data collected through a real-world experiment on a section of a two-lane state road using a GPS device. The analysis showed that the traditional safety margins for sharp curves are unrealistically large compared with the margins defined by the proposed approach; this indicates that the conventional approach uses a larger friction margin than the optimum friction margin. Consequently, the conventional approach results in the application of curves with radii smaller than those required for safe driving. Moreover, the results show that braking on a sharp curve on a steep downgrade is the most critical situation for the loss of lateral vehicle stability. Overall, this study highlights the significance of incorporating additional factors in the design procedure for horizontal curves that affect the safety of the curve, which are not considered in the point-mass model. The most significant factors considered in this study were the grade, driving maneuver in terms of speed change, operating speed, and vehicle path radius. The primary objective of this research was to establish a reliable road design methodology for reducing single-vehicle accidents on horizontal curves. The proposed approach enables the identification of horizontal curves with insufficient side friction, by calculating the difference between the available side friction factor and side friction demand. In a conventional road design practice, the vehicle is approximated as a point mass, and the effects of grade, speed change, vehicle dimensions, and uneven force distribution on individual axles are ignored. Instead, in the novel approach, the steady-state bicycle model was used, considering the aforementioned factors combined with more-realistic speeds and path radii. The improved approach provides a more comprehensive understanding of the design of safe curves, with an emphasis on previously neglected important influential factors (longitudinal grade and driver behavior in terms of operating speed and path radius). The improved design consistency approach could be used for quantifying the risk of skidding, both in the design stage of new roads and for improvement of existing roads.


  • The impact of different saturation headway values on intersection capacity

    by Dražen Cvitanić, Biljana Maljković

    Elements of the city road network that determine its capacity are signalized intersections. Their capacity depends of many factors: traffic volume and distribution, traffic flow structure, signal timing, and number of bicyclists and pedestrians. However, the starting parameter for calculation of intersection capacity is saturation headway. This research explores the influence of weather conditions and purpose of trip on saturation headway. Saturation headways were determined on few intersections in the morning peak hour of working and weekend day, in good and bad weather conditions. The impact of different trip purposes and different weather conditions on intersection capacity is analysed, as well as the influence of using mean and median values of saturation headway when calculating the intersection capacity.