Kittiwat Wingprawat
Research Subjects
Kittiwat Wingprawat has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Chaturong Pornrattanamaneewong
Department of Orthopaedic Surgery, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok, Thailand
1 shared publication - Keerati Chareancholvanich
Department of Orthopaedic Surgery, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok, Thailand
1 shared publication - Pakpoom Ruangsomboon
From the Division of Orthopaedic Surgery, Sunnybrook Health Sciences Centre, Toronto, ON (Dr. P. Ruangsomboon); the Faculty of Medicine, Siriraj Hospital, Mahidol University, Salaya, Thailand (Dr. P. Ruangsomboon, Dr. O. Ruangsomboon, Dr. Awirotananon, and Dr. Udomkiat); and the Upstream Lab, MAP Centre for Urban Health Solutions, Li Ka Shing Knowledge Institute, Unity Health Toronto, Toronto, ON (Dr. O. Ruangsomboon)
1 shared publication - Rapeepat Narkbunnam
Department of Orthopaedic Surgery, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok, Thailand
1 shared publication
Latest Publications
- 26 March 2021
- Published by Springer Nature in European Journal of Orthopaedic Surgery & Traumatology
- Vol. 32 (1) , 175-181
Accuracy of empirical distal femoral valgus cut angle of 4° to 6° in total knee arthroplasty: a randomized controlled trial
Introduction Currently, the best and simplest way that used to select the distal femoral valgus cut (DFVC) angle in total knee arthroplasty (TKA) is standing long leg radiograph. However, this kind of film is still not available in all hospitals. The purpose of this study is to compare the accuracy of different empirical DFVC angles in the restoration of the neutral mechanical alignment of the femoral component after TKA. Method 125 patients who diagnosed primary osteoarthritic knee and underwent unilateral TKA were randomly assigned into three groups: A, B, and C, according to the use of an intramedullary guide with the DFVC angle of 4°, 5°, and 6°, respectively. At three months after surgery, anteroposterior hip-to-ankle computed tomography (CT) scanograms were evaluated. Mechanical axis angle (MAA), mechanical lateral distal femoral angle (LDFA), femoral bowing, femoral neck-shaft angle (FNSA), and outliers of femoral component position were measured and compared among three groups. Independent influencing factors for the outliers > ±3° were determined using binary logistic regression analysis. Results Group B was older than group A. There were no significant differences of postoperative MAA, LDFA, femoral bowing, and FNSA among three groups. Outliers > ±3° of femoral component position in each group were 14.6%, 19.0%, and 16.7%, respectively (p = 0.865). When considering the outliers > ±2°, group C (35.7%) had a trend to have fewer outliers than groups A and B (41.5 and 42.9%). However, this finding was not reached the statistical significance (p = 0.778). Femoral bowing was only significantly influencing factors that related to the outliers > ±3° (p = 0.003). Conclusion This study demonstrates that there are no significant differences in coronal femoral component alignment among using the DFVC angle of 4°, 5°, and 6°. The use of the DFVC angle of 6° had a trend to reduce the outliers. Nevertheless, femoral bowing is the crucial influencing factor for selecting the degree of DFVC angle.
- 26 March 2021
- Published by Springer Nature in European Journal of Orthopaedic Surgery & Traumatology
- Vol. 32 (1) , 175-181
Accuracy of empirical distal femoral valgus cut angle of 4° to 6° in total knee arthroplasty: a randomized controlled trial
Introduction Currently, the best and simplest way that used to select the distal femoral valgus cut (DFVC) angle in total knee arthroplasty (TKA) is standing long leg radiograph. However, this kind of film is still not available in all hospitals. The purpose of this study is to compare the accuracy of different empirical DFVC angles in the restoration of the neutral mechanical alignment of the femoral component after TKA. Method 125 patients who diagnosed primary osteoarthritic knee and underwent unilateral TKA were randomly assigned into three groups: A, B, and C, according to the use of an intramedullary guide with the DFVC angle of 4°, 5°, and 6°, respectively. At three months after surgery, anteroposterior hip-to-ankle computed tomography (CT) scanograms were evaluated. Mechanical axis angle (MAA), mechanical lateral distal femoral angle (LDFA), femoral bowing, femoral neck-shaft angle (FNSA), and outliers of femoral component position were measured and compared among three groups. Independent influencing factors for the outliers > ±3° were determined using binary logistic regression analysis. Results Group B was older than group A. There were no significant differences of postoperative MAA, LDFA, femoral bowing, and FNSA among three groups. Outliers > ±3° of femoral component position in each group were 14.6%, 19.0%, and 16.7%, respectively (p = 0.865). When considering the outliers > ±2°, group C (35.7%) had a trend to have fewer outliers than groups A and B (41.5 and 42.9%). However, this finding was not reached the statistical significance (p = 0.778). Femoral bowing was only significantly influencing factors that related to the outliers > ±3° (p = 0.003). Conclusion This study demonstrates that there are no significant differences in coronal femoral component alignment among using the DFVC angle of 4°, 5°, and 6°. The use of the DFVC angle of 6° had a trend to reduce the outliers. Nevertheless, femoral bowing is the crucial influencing factor for selecting the degree of DFVC angle.