María Alejandra Morales Sánchez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
María Alejandra Morales Sánchez has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Alicia Porras
Universidad de los Andes
6 shared publications - Alejandro Maranon
Universidad de los Andes
5 shared publications - Camilo Hernandez
Escuela Colombiana de Ingeniería Julio Garavito
4 shared publications - Véronique Michaud
Laboratory for Processing of Advanced Composites, Ecole Polytechnique Fédérale de Lausanne, 1015 Lausanne, Switzerland
2 shared publications - Ana M. Rueda
Grupo de Diseño de Productos y Procesos (GDPP), Department of Chemical and Food Engineering, Universidad de los Andes, CR 1 18a 12, Bogotá 111711, Colombia
1 shared publication - Ana Sofía Hozman Manrique
Grupo de Diseño de Productos y Procesos (GDPP), Department of Chemical and Food Engineering, School of Engineering, Universidad de los Andes, CR 1 No. 18A-12, Bogota 111711, Colombia
1 shared publication
Latest Publications
- Open Access
- 24 September 2024
- Published by Asociacion Colombiana de Facultades de Ingenieriia (ACOFI) in Encuentro Internacional de Educación en Ingeniería
- p. 1-12
Composite development and characterization: Cocoa Bean shell and Propylene – Ethylene – 1 - Butene Terpolymer for potential fused granular fabrication applications
Approximately 5.5 billion tons of agroindustrial waste are generated annually worldwide[1]. A substantial portion of this waste remains untreated, leading to soil disposal and the production of greenhouse gases[2]. Specifically, the cocoa industry generates an estimated 700 thousand tons of waste annually[3]. The growing interest in sustainability has driven industries to adopt Circular Economy principles with a focus on utilizing residues from various industries to manufacture cost-competitive and eco-friendlier goods. This study presents a composite based on cocoa bean shells (CBS) and propylene-ethylene-1-butene terpolymer (PP-T), with a focus on its physical, thermal, and mechanical characteristics and its potential application in Fused Granular Fabrication (FGF). The raw materials, and the composite (10wt.% CBS), were thermally characterized, including thermogravimetric analysis (ASTME1121) and differential scanning calorimetry (ASTM D3418). Physical properties were assessed through water absorption (ASTMD570) and density (ASTM D792) analysis, while chemical characterization was achieved using FTIR. Tensile (ASTM D638) and flexural (ASTM D790) properties, were determined by testing molded compressed specimens. The developed material's potential application in FGF was explored. The study was focused on the determination of 3D printing temperature and provides a comprehensive tensile (ASTM D3039) and flexural characterization of 3D-printed specimens. It is essential to ensure that the processing temperature is above the polymer melting temperature (~130°C) while remaining below the thermal degradation temperature of CBS (~230°C). Water absorption shows the importance of well-dried materials before processing to avoid the presence of voids in the composite. Density does not show significant variations. Tensile properties proved to be comparable between the neat PP-T and the composite. Furthermore, the flexural strength showed improvement in the composite, increasing by 43%. The application of the developed composite pellets in FGF was explored. A temperature tower was 3D-printed to assess the impact of nine extrusion temperatures on the finishing quality of the piece. This process facilitated the selection of the 3D printing temperature. The tensile strength in the composite was reduced by 27% compared to the neat PP-T. This decrease can be attributed to the CBS acting as fillers. In this case, the flexural strain was comparable for both materials (7.8% - neat PP-T / 7.6% - composite). The composite's potential as a sustainable and functional alternative in additive manufacturing is notable. Characterization demonstrates a direct influence of the natural fiber from CBS on thermo-physical-mechanical properties. The feasibility of manufacturing the composite through 3D printing via FGF was demonstrated, presenting a practical and viable opportunity for producing parts with diverse requirements.
- 24 September 2024
- Published by Asociacion Colombiana de Facultades de Ingenieriia (ACOFI) in Encuentro Internacional de Educación en Ingeniería
- p. 1-12
Open AccessComposite development and characterization: Cocoa Bean shell and Propylene – Ethylene – 1 - Butene Terpolymer for potential fused granular fabrication applications
Approximately 5.5 billion tons of agroindustrial waste are generated annually worldwide[1]. A substantial portion of this waste remains untreated, leading to soil disposal and the production of greenhouse gases[2]. Specifically, the cocoa industry generates an estimated 700 thousand tons of waste annually[3]. The growing interest in sustainability has driven industries to adopt Circular Economy principles with a focus on utilizing residues from various industries to manufacture cost-competitive and eco-friendlier goods. This study presents a composite based on cocoa bean shells (CBS) and propylene-ethylene-1-butene terpolymer (PP-T), with a focus on its physical, thermal, and mechanical characteristics and its potential application in Fused Granular Fabrication (FGF). The raw materials, and the composite (10wt.% CBS), were thermally characterized, including thermogravimetric analysis (ASTME1121) and differential scanning calorimetry (ASTM D3418). Physical properties were assessed through water absorption (ASTMD570) and density (ASTM D792) analysis, while chemical characterization was achieved using FTIR. Tensile (ASTM D638) and flexural (ASTM D790) properties, were determined by testing molded compressed specimens. The developed material's potential application in FGF was explored. The study was focused on the determination of 3D printing temperature and provides a comprehensive tensile (ASTM D3039) and flexural characterization of 3D-printed specimens. It is essential to ensure that the processing temperature is above the polymer melting temperature (~130°C) while remaining below the thermal degradation temperature of CBS (~230°C). Water absorption shows the importance of well-dried materials before processing to avoid the presence of voids in the composite. Density does not show significant variations. Tensile properties proved to be comparable between the neat PP-T and the composite. Furthermore, the flexural strength showed improvement in the composite, increasing by 43%. The application of the developed composite pellets in FGF was explored. A temperature tower was 3D-printed to assess the impact of nine extrusion temperatures on the finishing quality of the piece. This process facilitated the selection of the 3D printing temperature. The tensile strength in the composite was reduced by 27% compared to the neat PP-T. This decrease can be attributed to the CBS acting as fillers. In this case, the flexural strain was comparable for both materials (7.8% - neat PP-T / 7.6% - composite). The composite's potential as a sustainable and functional alternative in additive manufacturing is notable. Characterization demonstrates a direct influence of the natural fiber from CBS on thermo-physical-mechanical properties. The feasibility of manufacturing the composite through 3D printing via FGF was demonstrated, presenting a practical and viable opportunity for producing parts with diverse requirements.
- Open Access
Colombian Sustainability Perspective on Fused Deposition Modeling Technology: Opportunity to Develop Recycled and Biobased 3D Printing Filaments
In the context of the preservation of natural resources, researchers show a growing interest in developing eco—friendly materials based on recycled polymers and natural fiber biocomposites to minimize plastic and agroindustrial waste pollution. The development of new materials must be integrated within the circular economy concepts to guarantee sustainable production. In parallel, fused deposition modeling, an additive manufacturing technology, provides the opportunity to use these new materials in an efficient and sustainable manner. This review presents the context of plastics and agro-industrial fiber pollution, followed by the opportunity to give them added value by applying circular economy concepts and implementing these residues to develop new materials for the manufacture of fused deposition modeling 3D printing technique feedstock. Colombian perspective is highlighted since 3D printing technology is growing there, and Colombian biodiversity represents a high reservoir of materials. Also, recycling in Colombia promotes compliance with the 2030 Agenda and the Sustainable Development Goals.
Open AccessColombian Sustainability Perspective on Fused Deposition Modeling Technology: Opportunity to Develop Recycled and Biobased 3D Printing Filaments
In the context of the preservation of natural resources, researchers show a growing interest in developing eco—friendly materials based on recycled polymers and natural fiber biocomposites to minimize plastic and agroindustrial waste pollution. The development of new materials must be integrated within the circular economy concepts to guarantee sustainable production. In parallel, fused deposition modeling, an additive manufacturing technology, provides the opportunity to use these new materials in an efficient and sustainable manner. This review presents the context of plastics and agro-industrial fiber pollution, followed by the opportunity to give them added value by applying circular economy concepts and implementing these residues to develop new materials for the manufacture of fused deposition modeling 3D printing technique feedstock. Colombian perspective is highlighted since 3D printing technology is growing there, and Colombian biodiversity represents a high reservoir of materials. Also, recycling in Colombia promotes compliance with the 2030 Agenda and the Sustainable Development Goals.
- Open Access
Development and Characterization of Plantain (Musa paradisiaca) Flour-Based Biopolymer Films Reinforced with Plantain Fibers
Agroindustrial wastes are a cheap and abundant source of natural fibers and macromolecules that can be used in the manufacturing of biocomposites. This study presents the development and thermo-mechanical characterization of a bio-composite film (TPF/PF), made of thermoplastic banana flour (TPF) matrix and plantain fibers (PF). Fabricated materials were characterized by physical analysis, chemical composition, Fourier-transformed spectroscopy (FTIR), thermal analysis (TGA), mechanical analysis, and scanning electronic microscopy (SEM). The physical analysis showed that TPF and PF have a low density and high affinity to water resulting in a lightweight, renewable, and biodegradable TPF/PF composite. The chemical composition and spectra analysis of the fiber showed that PF is a potential candidate for reinforcing composites due to its high α-cellulose and low lignin content. The thermal analysis determined that TPF degrades at a lower temperature than PF, therefore the matrix sets the processing temperature for TPF/PF composite films. The mechanical test showed an improvement in the tensile properties of the composite in comparison to neat TPF. Tensile strength and Young’s modulus were improved by 345% and 1196%, respectively, when PF fibers was used. Good bonding and mechanical interlocking of PF to the TPF were identified by SEM. Therefore, potential biocomposites can be developed using natural fibers and thermoplastic starches obtained from plantain agroindustrial wastes.
Open AccessDevelopment and Characterization of Plantain (Musa paradisiaca) Flour-Based Biopolymer Films Reinforced with Plantain Fibers
Agroindustrial wastes are a cheap and abundant source of natural fibers and macromolecules that can be used in the manufacturing of biocomposites. This study presents the development and thermo-mechanical characterization of a bio-composite film (TPF/PF), made of thermoplastic banana flour (TPF) matrix and plantain fibers (PF). Fabricated materials were characterized by physical analysis, chemical composition, Fourier-transformed spectroscopy (FTIR), thermal analysis (TGA), mechanical analysis, and scanning electronic microscopy (SEM). The physical analysis showed that TPF and PF have a low density and high affinity to water resulting in a lightweight, renewable, and biodegradable TPF/PF composite. The chemical composition and spectra analysis of the fiber showed that PF is a potential candidate for reinforcing composites due to its high α-cellulose and low lignin content. The thermal analysis determined that TPF degrades at a lower temperature than PF, therefore the matrix sets the processing temperature for TPF/PF composite films. The mechanical test showed an improvement in the tensile properties of the composite in comparison to neat TPF. Tensile strength and Young’s modulus were improved by 345% and 1196%, respectively, when PF fibers was used. Good bonding and mechanical interlocking of PF to the TPF were identified by SEM. Therefore, potential biocomposites can be developed using natural fibers and thermoplastic starches obtained from plantain agroindustrial wastes.
- Open Access
Bioactive Poly(lactic acid)–Cocoa Bean Shell Composites for Biomaterial Formulation: Preparation and Preliminary In Vitro Characterization
The unique lignocellulosic and solvent-extractive chemical constituents of most natural fibers are rich in natural polymers and bioactive molecules that can be exploited for biomaterial formulation. However, although natural fibers’ main constituents have been already incorporated as material reinforcement and improve surface bioactivity of polymeric materials, the use of the whole natural fibers as bioactive fillers remains largely unexplored. Thus, we put forward the formulation of natural fiber filling and functionalization of biomaterials by studying the chemical composition of cocoa bean shells (CBS) and proposing the fabrication and characterization of polylactic acid (PLA) and CBS-based composite by solvent-casting. As was expected from previous studies of agro-industrial wastes, the main components of CBS were to cellulose (42.23 wt.%), lignin (22.68 wt.%), hemicellulose (14.73 wt.%), and solvent extractives (14.42 wt.%). Structural analysis (FTIR) confirms the absence of covalent bonding between materials. Thermal degradation profiles (DSC and TGA) showed similar mass losses and thermal-reaction profiles for lignocellulosic-fibers-based composites. The mechanical behavior of the PLA/CBS composite shows a stiffer material behavior than the pristine material. The cell viability of Vero cells in the presence of the composites was above 94%, and the hemolytic tendency was below 5%, while platelet aggregation increased up to 40%. Antioxidant activity was confirmed with comparable 2,2-diphe-277 nyl-1-picryl-hydrazyl-hydrate (DPPH) free-radical scavenging than Vitamin C even for PLA/CBS composite. Therefore, the present study elucidates the significant promise of CBS for bioactive functionalization in biomaterial-engineering, as the tested composite exhibited high biocompatibility and strong antioxidant activity and might induce angiogenic factors’ release. Moreover, we present an eco-friendly alternative to taking advantage of chocolate-industry by-products.
Open AccessBioactive Poly(lactic acid)–Cocoa Bean Shell Composites for Biomaterial Formulation: Preparation and Preliminary In Vitro Characterization
The unique lignocellulosic and solvent-extractive chemical constituents of most natural fibers are rich in natural polymers and bioactive molecules that can be exploited for biomaterial formulation. However, although natural fibers’ main constituents have been already incorporated as material reinforcement and improve surface bioactivity of polymeric materials, the use of the whole natural fibers as bioactive fillers remains largely unexplored. Thus, we put forward the formulation of natural fiber filling and functionalization of biomaterials by studying the chemical composition of cocoa bean shells (CBS) and proposing the fabrication and characterization of polylactic acid (PLA) and CBS-based composite by solvent-casting. As was expected from previous studies of agro-industrial wastes, the main components of CBS were to cellulose (42.23 wt.%), lignin (22.68 wt.%), hemicellulose (14.73 wt.%), and solvent extractives (14.42 wt.%). Structural analysis (FTIR) confirms the absence of covalent bonding between materials. Thermal degradation profiles (DSC and TGA) showed similar mass losses and thermal-reaction profiles for lignocellulosic-fibers-based composites. The mechanical behavior of the PLA/CBS composite shows a stiffer material behavior than the pristine material. The cell viability of Vero cells in the presence of the composites was above 94%, and the hemolytic tendency was below 5%, while platelet aggregation increased up to 40%. Antioxidant activity was confirmed with comparable 2,2-diphe-277 nyl-1-picryl-hydrazyl-hydrate (DPPH) free-radical scavenging than Vitamin C even for PLA/CBS composite. Therefore, the present study elucidates the significant promise of CBS for bioactive functionalization in biomaterial-engineering, as the tested composite exhibited high biocompatibility and strong antioxidant activity and might induce angiogenic factors’ release. Moreover, we present an eco-friendly alternative to taking advantage of chocolate-industry by-products.
- Open Access
Development and Characterization of a 3D Printed Cocoa Bean Shell Filled Recycled Polypropylene for Sustainable Composites
Natural filler-based composites are an environmentally friendly and potentially sustainable alternative to synthetic or plastic counterparts. Recycling polymers and using agro-industrial wastes are measures that help to achieve a circular economy. Thus, this work presents the development and characterization of a 3D printing filament based on recycled polypropylene and cocoa bean shells, which has not been explored yet. The obtained composites were thermally and physically characterized. In addition, the warping effect, mechanical, and morphological analyses were performed on 3D printed specimens. Thermal analysis exhibited decreased thermal stability when cacao bean shell (CBS) particles were added due to their lignocellulosic content. A reduction in both melting enthalpy and crystallinity percentage was identified. This is caused by the increase in the amorphous structures present in the hemicellulose and lignin of the CBS. Mechanical tests showed high dependence of the mechanical properties on the 3D printing raster angle. Tensile strength increased when a raster angle of 0° was used, compared to specimens printed at 90°, due to the load direction. Tensile strength and fracture strain were improved with CBS addition in specimens printed at 90°, and better bonding between adjacent layers was achieved. Electron microscope images identified particle fracture, filler-matrix debonding, and matrix breakage as the central failure mechanisms. These failure mechanisms are attributed to the poor interfacial bonding between the CBS particles and the matrix, which reduced the tensile properties of specimens printed at 0°. On the other hand, the printing process showed that cocoa bean shell particles reduced by 67% the characteristic warping effect of recycled polypropylene during 3D printing, which is advantageous for 3D printing applications of the rPP. Thereby, potential sustainable natural filler composite filaments for 3D printing applications with low density and low cost can be developed, adding value to agro-industrial and plastic wastes.
Open AccessDevelopment and Characterization of a 3D Printed Cocoa Bean Shell Filled Recycled Polypropylene for Sustainable Composites
Natural filler-based composites are an environmentally friendly and potentially sustainable alternative to synthetic or plastic counterparts. Recycling polymers and using agro-industrial wastes are measures that help to achieve a circular economy. Thus, this work presents the development and characterization of a 3D printing filament based on recycled polypropylene and cocoa bean shells, which has not been explored yet. The obtained composites were thermally and physically characterized. In addition, the warping effect, mechanical, and morphological analyses were performed on 3D printed specimens. Thermal analysis exhibited decreased thermal stability when cacao bean shell (CBS) particles were added due to their lignocellulosic content. A reduction in both melting enthalpy and crystallinity percentage was identified. This is caused by the increase in the amorphous structures present in the hemicellulose and lignin of the CBS. Mechanical tests showed high dependence of the mechanical properties on the 3D printing raster angle. Tensile strength increased when a raster angle of 0° was used, compared to specimens printed at 90°, due to the load direction. Tensile strength and fracture strain were improved with CBS addition in specimens printed at 90°, and better bonding between adjacent layers was achieved. Electron microscope images identified particle fracture, filler-matrix debonding, and matrix breakage as the central failure mechanisms. These failure mechanisms are attributed to the poor interfacial bonding between the CBS particles and the matrix, which reduced the tensile properties of specimens printed at 0°. On the other hand, the printing process showed that cocoa bean shell particles reduced by 67% the characteristic warping effect of recycled polypropylene during 3D printing, which is advantageous for 3D printing applications of the rPP. Thereby, potential sustainable natural filler composite filaments for 3D printing applications with low density and low cost can be developed, adding value to agro-industrial and plastic wastes.
- Open Access
Development and Characterization of Rice Husk and Recycled Polypropylene Composite Filaments for 3D Printing
Nowadays the use of natural fiber composites has gained significant interest due to their low density, high availability, and low cost. The present study explores the development of sustainable 3D printing filaments based on rice husk (RH), an agricultural residue, and recycled polypropylene (rPP) and the influence of fiber weight ratio on physical, thermal, mechanical, and morphological properties of 3D printing parts. Thermogravimetric analysis revealed that the composite’s degradation process started earlier than for the neat rPP due to the lignocellulosic fiber components. Mechanical tests showed that tensile strength increased when using a raster angle of 0° than specimens printed at 90°, due to the weaker inter-layer bonding compared to in-layer. Furthermore, inter layer bonding tensile strength was similar for all tested materials. Scanning electron microscope (SEM) images revealed the limited interaction between the untreated fiber and matrix, which led to reduced tensile properties. However, during the printing process, composites presented lower warping than printed neat rPP. Thus, 3D printable ecofriendly natural fiber composite filaments with low density and low cost can be developed and used for 3D printing applications, contributing to reduce the impact of plastic and agricultural waste.
Open AccessDevelopment and Characterization of Rice Husk and Recycled Polypropylene Composite Filaments for 3D Printing
Nowadays the use of natural fiber composites has gained significant interest due to their low density, high availability, and low cost. The present study explores the development of sustainable 3D printing filaments based on rice husk (RH), an agricultural residue, and recycled polypropylene (rPP) and the influence of fiber weight ratio on physical, thermal, mechanical, and morphological properties of 3D printing parts. Thermogravimetric analysis revealed that the composite’s degradation process started earlier than for the neat rPP due to the lignocellulosic fiber components. Mechanical tests showed that tensile strength increased when using a raster angle of 0° than specimens printed at 90°, due to the weaker inter-layer bonding compared to in-layer. Furthermore, inter layer bonding tensile strength was similar for all tested materials. Scanning electron microscope (SEM) images revealed the limited interaction between the untreated fiber and matrix, which led to reduced tensile properties. However, during the printing process, composites presented lower warping than printed neat rPP. Thus, 3D printable ecofriendly natural fiber composite filaments with low density and low cost can be developed and used for 3D printing applications, contributing to reduce the impact of plastic and agricultural waste.