EEElixabete Espinosa

Elixabete Espinosa

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Elixabete Espinosa has a total of 22 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Mechanical properties of additively manufactured AlSi7Mg0.6 and IN718 thin-walled structures

    by Tim Röver, Brian Biluh, Dirk Herzog, Emma Gil, Ane Miren Mancisidor, Jon Aranzabe, M. Belén García-Blanco, Elixabete Espinosa, Ephraïm Toubiana, Leire Arrieta-Lizarazu, et al.

    Additively manufactured heat exchanger cores offer enhanced compactness, thermomechanical robustness, and improved integration within confined assembly spaces. However, their complex thin-walled lattice structures pose significant challenges for mechanical characterization and conventional finite element analysis, due to high computational costs. This study investigates the tensile mechanical properties of grid-like structures produced by powder bed fusion with a laser beam in aluminum alloy AlSi7Mg0.6 and nickel–chromium-based superalloy Inconel 718 (IN718). Samples with varying wall thicknesses were fabricated, heat treated, and some were surface treated to reduce surface roughness. Tensile tests combined with digital image correlation and non-linear finite element modeling were conducted to evaluate mechanical behavior. Experimental results reveal that a minimum solid material proportion (P s ≈ 0.09 for AlSi7Mg0.6; P s ≈ 0.06 for IN718) is required to achieve reliable elastoplastic deformation; below these thresholds, premature brittle failure dominates. Equivalent Young’s moduli and yield strength scale linearly with solid material proportion, the latter reaching approximately 59% and 52% of bulk material values for AlSi7Mg0.6 and IN718, respectively. Surface treatment contributed mainly to wall thickness reduction without significantly altering mechanical performance. Homogenized porous material models based on the Gibson–Ashby framework and a modified Hockett–Sherby constitutive law were developed, enabling efficient and realistic simulation of these complex structures. These findings provide critical experimental data and modeling tools essential for the design and optimization of next-generation additively manufactured heat exchangers in both alloys.


  • Open Access

    Effect of Post-Processing Treatment on Fatigue Performance of Ti6Al4V Alloy Manufactured by Laser Powder Bed Fusion

    by Ane Miren Mancisidor, María Belén García-Blanco, Iban Quintana, Pedro José Arrazola, Elixabete Espinosa, Mikel Cuesta, Joseba Albizuri, Fermin Garciandia

    Fatigue properties of parts are of particular concern for safety-critical structures. It is well-known that discontinuities in shape or non-uniformities in materials are frequently a potential nucleus of fatigue failure. This is especially crucial for the Ti6Al4V alloy, which presents high susceptibility to the notch effect. This study investigates how post-processing treatments affect the mechanical performance of Ti6Al4V samples manufactured by laser powder bed fusion technology. All the fatigue samples were subjected to a HIP cycle and post-processed by machining and using combinations of alternative mechanical and electrochemical surface treatments. The relationship between surface properties such as roughness, topography and residual stresses with fatigue performance was assessed. Compressive residual stresses were introduced in all surface-treated samples, and after tribofinishing, roughness was reduced to 0.31 ± 0.10 µm, which was found to be the most critical factor. Fractures occurred on the surface as HIP removed critical internal defects. The irregularities found in the form of cavities or pits were stress concentrators that initiated cracks. It was concluded that machined surfaces presented a fatigue behavior comparable to wrought material, offering a fatigue limit superior to 450 MPa. Additionally, alternative surface treatments showed a fatigue behavior equivalent to the casting material.


  • Open Access

    Prediction of Surface Roughness of SLM Built Parts after Finishing Processes Using an Artificial Neural Network

    by Daniel Soler, Martín Telleria, M. Belén García-Blanco, Elixabete Espinosa, Mikel Cuesta, Pedro José Arrazola

    A known problem of additive manufactured parts is their poor surface quality, which influences product performance. There are different surface treatments to improve surface quality: blasting is commonly employed to improve mechanical properties and reduce surface roughness, and electropolishing to clean shot peened surfaces and improve the surface roughness. However, the final surface roughness is conditioned by multiple parameters related to these techniques. This paper presents a prediction model of surface roughness (Ra) using an Artificial Neural Network considering two parameters of the SLM manufacturing process and seven blasting and electropolishing processes. This model is proven to be in agreement with 429 experimental results. Moreover, this model is then used to find the optimal conditions to be applied during the blasting and the electropolishing in order to improve the surface roughness by roughly 60%.


  • Comparative study of different surface treatments applied to Ti6Al4V parts produced by Selective Laser Melting

    by M. B. García-Blanco, M. Díaz-Fuentes, E. Espinosa, A. M. Mancisidor, G. Vara

    SLM (Selective Laser Melting) is an AM (Additive Manufacturing) technology able to manufacture components with high structural integrity; however, a key drawback is the resulting poor surface quality of these parts. In order to reduce the roughness of these surfaces different treatments could be applied, but all of them have limitations when applied to SLM parts. One of the main challenges for surface treatments is to provide quality surfaces regardless of its starting state or geometry. Currently, chemical polishing is the best positioned treatment to achieve this but it usually employs hazardous electrolytes. Therefore, more comparative data about the performance of alternative treatments to polish parts with different geometrical characteristics are required by industry. In this study, electropolishing, blasting and laser have been applied, either separately or combined, to complex SLM Ti6Al4 V parts. The most promising technologies have been also applied to parts with different planes and internal cavities.