Hasan Efeoglu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hasan Efeoglu has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Abdulmecit Turut
Faculty of Engineering and Natural Sciences, Department of Engineering Physics, Istanbul Medeniyet University , Ünalan, Üskudar, Istanbul 34700
4 shared publications - Ozlem Akin
Department of Nanoscience and Nanoengineering, Ataturk University, Erzurum, Türkiye
2 shared publications - Bahattin Abay
Department of Physics, Faculty of Science, Ataturk University, Erzurum, Turkey
1 shared publication İbrahim Y. Erdog˘an
1 shared publicationKadem Meral
Ataturk Univ, Fac Sci, Dept Chem, TR-25240 Erzurum, Turkey
1 shared publicationM Alieva
Atatürk Üniversitesi, Fen-Edebiyat Fakültesi, Fizik Bölümü, 25240-Erzurum, Turkey
1 shared publication
Latest Publications
- 29 July 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 43 (5)
Characterization of TaxO5−y thin films grown by HiPIMS reactive sputtering for temperature sensing applications
Temperature sensors with a negative temperature coefficient are widely used in various sectors because of their numerous benefits and practical applications. However, linearity over narrow ranges restricts extensive use compared to other temperature sensors, especially in the cryogenic region. This study investigated tantalum oxide (TaxO5−y) thin films and their potential for temperature sensing capabilities spanning the cryogenics to the room-temperature region due to their strong chemical, physical, and electrical properties, such as a wide bandgap, chemical stability, high refractive index, and dielectric constant. The properties of thin films partially depend on fabrication techniques/parameters. This research uses the high-power impulse reactive sputter technique to produce TaxO5−y thin films. The thin film of 200 nm TaxO5−y depends on temperature, and the resistance vs temperature (R-T) shows almost linear relationships in the 20–320 K range. The absolute value of the temperature coefficient of resistance of this sensor at 294 K increased to −1.1% K−1 as it grew. The annealing effect on R-T properties, including physical and crystalline characteristics, was investigated for optimization, and bandgap energy was found to be 4.16 ± 0.025 eV. Annealing at different temperatures causes a decrease in resistance and a slight change in the R-T curve due to its crystallization.
- 29 July 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 43 (5)
Characterization of TaxO5−y thin films grown by HiPIMS reactive sputtering for temperature sensing applications
Temperature sensors with a negative temperature coefficient are widely used in various sectors because of their numerous benefits and practical applications. However, linearity over narrow ranges restricts extensive use compared to other temperature sensors, especially in the cryogenic region. This study investigated tantalum oxide (TaxO5−y) thin films and their potential for temperature sensing capabilities spanning the cryogenics to the room-temperature region due to their strong chemical, physical, and electrical properties, such as a wide bandgap, chemical stability, high refractive index, and dielectric constant. The properties of thin films partially depend on fabrication techniques/parameters. This research uses the high-power impulse reactive sputter technique to produce TaxO5−y thin films. The thin film of 200 nm TaxO5−y depends on temperature, and the resistance vs temperature (R-T) shows almost linear relationships in the 20–320 K range. The absolute value of the temperature coefficient of resistance of this sensor at 294 K increased to −1.1% K−1 as it grew. The annealing effect on R-T properties, including physical and crystalline characteristics, was investigated for optimization, and bandgap energy was found to be 4.16 ± 0.025 eV. Annealing at different temperatures causes a decrease in resistance and a slight change in the R-T curve due to its crystallization.
- Open Access
- 19 March 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 36 (8) , 1-13
Room temperature current conduction mechanisms in Ba0.5Sr0.5TiO3 and Ba0.5Sr0.5TiO3/TiO2 multilayer memristor structures
In this study, pure BaSrTiO3 (BST) thin films and layered BST/TiO2 thin films were fabricated on Cr/SiO2/Si substrates for a possible fourth passive device in electronics called a memristor. Radio frequency- and high-power impulse magnetron sputtering-based reactive sputtering was used for the deposition of films. While analyzing the memristor behavior by IV-t measurement at room temperature, optical, structural, surface morphology, thermal annealing effect, and current conduction mechanisms were investigated. The structures gained memristive behavior due to the oxygen vacancies displaced by the effect of annealing. As bipolar switching was observed in all memristor structures, the switching mechanism was identified as the valance change mechanism, in which conductivity is mostly provided by Poole–Frenkel and Schottky emission conduction mechanisms.
- 19 March 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 36 (8) , 1-13
Open AccessRoom temperature current conduction mechanisms in Ba0.5Sr0.5TiO3 and Ba0.5Sr0.5TiO3/TiO2 multilayer memristor structures
In this study, pure BaSrTiO3 (BST) thin films and layered BST/TiO2 thin films were fabricated on Cr/SiO2/Si substrates for a possible fourth passive device in electronics called a memristor. Radio frequency- and high-power impulse magnetron sputtering-based reactive sputtering was used for the deposition of films. While analyzing the memristor behavior by IV-t measurement at room temperature, optical, structural, surface morphology, thermal annealing effect, and current conduction mechanisms were investigated. The structures gained memristive behavior due to the oxygen vacancies displaced by the effect of annealing. As bipolar switching was observed in all memristor structures, the switching mechanism was identified as the valance change mechanism, in which conductivity is mostly provided by Poole–Frenkel and Schottky emission conduction mechanisms.
- 1 March 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 43 (2)
Experimental current-voltage-temperature and thermal sensitivity behaviors of an ideal Schottky barrier diode over a wide temperature range
The Pt/epitaxy n-Si/n+Si Schottky barrier diodes (SBDs) with a Schottky contact area of 9 × 10−4 cm2 were fabricated, and their experimental current-voltage (I-V) characteristics exhibited an ideal behavior in the 20–320 K range. We investigated the thermal sensitivity behavior of this SBD, which exhibits an ideal behavior. The series resistance Rs value remained approximately unchanged as 10.00 Ω at 20 K and 9.258 Ω at 320 K. A barrier height value of qΦb0=0.807eV at 320 K shows a slight decrease to 120 K, and the ideality factor n value shows a slight increase from 1.016 at 320 to 1.070 at 120 K. Furthermore, the sharp decrease in qΦb0 value, from 120 to 20 K, was ascribed to the barrier height inhomogeneity due to the low-barrier patches at the Pt/n-Si interface. It has been seen that the forward bias voltage-temperature (V-T) curves for the thermal sensitivity behavior have two linear regions, the low temperature region (LTR) and high temperature region (HTR), at each current level from 1.0 pA to 1.0 mA. The thermal sensitivity coefficient α from the slope of the VT curve increased with a decrease at the current level in both regions. At each current level, the V-T curves give higher α values in the HTR than those in the LTR. The α value ranged from 3.302 mV/K at 1.0 pA to 1.590 mV/K at 1.0 mA in the HTR. As a result, it was concluded that the Pt/n-Si diode can be used as a high-sensitivity thermal diode for sensor applications since its thermal sensitivity values coincide with the literature values.
- 1 March 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 43 (2)
Experimental current-voltage-temperature and thermal sensitivity behaviors of an ideal Schottky barrier diode over a wide temperature range
The Pt/epitaxy n-Si/n+Si Schottky barrier diodes (SBDs) with a Schottky contact area of 9 × 10−4 cm2 were fabricated, and their experimental current-voltage (I-V) characteristics exhibited an ideal behavior in the 20–320 K range. We investigated the thermal sensitivity behavior of this SBD, which exhibits an ideal behavior. The series resistance Rs value remained approximately unchanged as 10.00 Ω at 20 K and 9.258 Ω at 320 K. A barrier height value of qΦb0=0.807eV at 320 K shows a slight decrease to 120 K, and the ideality factor n value shows a slight increase from 1.016 at 320 to 1.070 at 120 K. Furthermore, the sharp decrease in qΦb0 value, from 120 to 20 K, was ascribed to the barrier height inhomogeneity due to the low-barrier patches at the Pt/n-Si interface. It has been seen that the forward bias voltage-temperature (V-T) curves for the thermal sensitivity behavior have two linear regions, the low temperature region (LTR) and high temperature region (HTR), at each current level from 1.0 pA to 1.0 mA. The thermal sensitivity coefficient α from the slope of the VT curve increased with a decrease at the current level in both regions. At each current level, the V-T curves give higher α values in the HTR than those in the LTR. The α value ranged from 3.302 mV/K at 1.0 pA to 1.590 mV/K at 1.0 mA in the HTR. As a result, it was concluded that the Pt/n-Si diode can be used as a high-sensitivity thermal diode for sensor applications since its thermal sensitivity values coincide with the literature values.
- Open Access
- 27 February 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 36 (6) , 1-9
Investigation of the memristive properties of the device form and thin film form of BST and CeO2 films with different arrays
In this study, a memristor structure known as a missing circuit element was produced. This study consists of a total of six samples in both thin film and device form with different arrays of BST film and CeO2 film on SiO2/Si substrate. The effects of different arrays and device forms of these two films on memristive behavior were investigated. It was observed that the structures exhibited memristive behavior due to the difference in ion mobility in films with different dielectric constants. It was also observed that the structures changed their memristive behavior in the annealing process performed at different temperatures. It was observed that the memristive behaviors examined imitated the connection strength of artificial synapses, and they are suitable for the production of multi-bit memristors or analog memristors suitable for the creation of artificial neuromorphic networks.
- 27 February 2025
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 36 (6) , 1-9
Open AccessInvestigation of the memristive properties of the device form and thin film form of BST and CeO2 films with different arrays
In this study, a memristor structure known as a missing circuit element was produced. This study consists of a total of six samples in both thin film and device form with different arrays of BST film and CeO2 film on SiO2/Si substrate. The effects of different arrays and device forms of these two films on memristive behavior were investigated. It was observed that the structures exhibited memristive behavior due to the difference in ion mobility in films with different dielectric constants. It was also observed that the structures changed their memristive behavior in the annealing process performed at different temperatures. It was observed that the memristive behaviors examined imitated the connection strength of artificial synapses, and they are suitable for the production of multi-bit memristors or analog memristors suitable for the creation of artificial neuromorphic networks.
- 20 January 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (3) , 2460-2470
Numerical Analysis of Thermal Sensitivity Characteristics by Pinch-Off Model in Inhomogeneous Schottky Barrier Diodes
- 20 January 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (3) , 2460-2470
Numerical Analysis of Thermal Sensitivity Characteristics by Pinch-Off Model in Inhomogeneous Schottky Barrier Diodes
- 1 March 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 41 (2) , 022207
Thermal sensing capability and current–voltage–temperature characteristics in Pt/n-GaP/Al/Ti Schottky diodes
We have discussed the thermal sensing capability under a constant current level and current versus voltage (I–V) traces by measuring the temperature of high series resistance Pt/n-GaP/Al/Ti Schottky structures in the 100−320 K range. The Rs values of 35 Ω and 4.50 × 103 kΩ for the device have been determined from I–V traces at 320 and 100 K, respectively. The thermal sensing (V–T) curves are expected to give a straight line at each current level. However, the V–T curves have deviated upward from linearity due to the high Rs value of the device after a certain temperature. The deviation point from linearity in V–T traces shifts to higher temperatures with an increase in bias voltage and current level. Thereby, the straight-line interval portion of the V–T curve has become too small with an increase in the current value. The thermal sensing coefficient α changed from 2.49 mV/K at 10 μA to 3.21 mV/K at 0.50 nA. Therefore, it has been concluded that the Pt/n-GaP/Al/Ti Schottky barrier (SB) is preferable for thermal sensor applications at the small current levels of 0.50, 1.0, 2.0, and 10.0 nA with high sensitivity up to a minimum temperature of 100 K. From I–V curves, qΦb0 and ideality factor values have ranged from 1.200 eV and 1.066 at 320 K to 0.854 eV and 1.705 at 100 K. It has been reported in the literature that the large SB height leads to a better temperature response.
- 1 March 2023
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 41 (2) , 022207
Thermal sensing capability and current–voltage–temperature characteristics in Pt/n-GaP/Al/Ti Schottky diodes
We have discussed the thermal sensing capability under a constant current level and current versus voltage (I–V) traces by measuring the temperature of high series resistance Pt/n-GaP/Al/Ti Schottky structures in the 100−320 K range. The Rs values of 35 Ω and 4.50 × 103 kΩ for the device have been determined from I–V traces at 320 and 100 K, respectively. The thermal sensing (V–T) curves are expected to give a straight line at each current level. However, the V–T curves have deviated upward from linearity due to the high Rs value of the device after a certain temperature. The deviation point from linearity in V–T traces shifts to higher temperatures with an increase in bias voltage and current level. Thereby, the straight-line interval portion of the V–T curve has become too small with an increase in the current value. The thermal sensing coefficient α changed from 2.49 mV/K at 10 μA to 3.21 mV/K at 0.50 nA. Therefore, it has been concluded that the Pt/n-GaP/Al/Ti Schottky barrier (SB) is preferable for thermal sensor applications at the small current levels of 0.50, 1.0, 2.0, and 10.0 nA with high sensitivity up to a minimum temperature of 100 K. From I–V curves, qΦb0 and ideality factor values have ranged from 1.200 eV and 1.066 at 320 K to 0.854 eV and 1.705 at 100 K. It has been reported in the literature that the large SB height leads to a better temperature response.
- 8 December 2022
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 52 (2) , 1410-1418
Current–Voltage Characteristics of Pt Metal-based and PtSi Silicide-based n-Si Schottky Diodes over a Wide Measuring Temperature Range
- 8 December 2022
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 52 (2) , 1410-1418
Current–Voltage Characteristics of Pt Metal-based and PtSi Silicide-based n-Si Schottky Diodes over a Wide Measuring Temperature Range
- 25 February 2022
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 33 (10) , 7423-7434
Formation of a Ti → TiO2-graded layer and its effect on the memristive properties of TiOx(/Ti/TiOx) structures
- 25 February 2022
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 33 (10) , 7423-7434
Formation of a Ti → TiO2-graded layer and its effect on the memristive properties of TiOx(/Ti/TiOx) structures
- 1 April 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 46, 7033-7039
Memristiv effect on W/Ti/p-Si structure: Aging phenomena and one of the origin of barrier inhomogeneity
- 1 April 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 46, 7033-7039
Memristiv effect on W/Ti/p-Si structure: Aging phenomena and one of the origin of barrier inhomogeneity
- 1 January 2010
- Published by Elsevier in Journal of Luminescence
- Vol. 130 (1) , 157-162
Anodization of aluminium thin films on p++Si and annihilation of strong luminescence from Al2O3
- 1 January 2010
- Published by Elsevier in Journal of Luminescence
- Vol. 130 (1) , 157-162
Anodization of aluminium thin films on p++Si and annihilation of strong luminescence from Al2O3