Pavel O. Yuryev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Pavel O. Yuryev has a total of 76 co-authors. Here are the top co-authors by number of shared publications:
- Igor Lazarevich Konstantinov
Siberian Federal University, Krasnoyarsk, Russian Federation
11 shared publications - Evgeniy Gennadyevich Partyko
School of Non-Ferrous Metals, Siberian Federal University, 660041 Krasnoyarsk, Russia
10 shared publications - Yuriy Viktorovich Baykovskiy
Siberian Federal University, Krasnoyarsk, Russian Federation
10 shared publications - Yulbarskhon Nabievich Mansurov
Department of Wagons and Wagon Economy, Tashkent State Transport University, Tashkent 100067, Uzbekistan
9 shared publications - Alexandr I. Bezrukikh
Siberian Federal University, Krasnoyarsk, Russian Federation
8 shared publications - Aleksandr Aleksandrovich Kosovich
School of Non-Ferrous Metals, Siberian Federal University, 660041 Krasnoyarsk, Russia
7 shared publications
Latest Publications
- 23 April 2026
- Published by Springer Nature in Metallurgist
- Vol. 69 (11) , 1-11
Rheological model for deformation of AK7 alloy
- 23 April 2026
- Published by Springer Nature in Metallurgist
- Vol. 69 (11) , 1-11
Rheological model for deformation of AK7 alloy
- Open Access
Multistage Recycling of Aluminum Casting Slags: Metal Extraction and Salt Flux Regeneration
The depletion of natural resources remains an acute global problem, highlighting the importance of developing sustainable technologies that enable the simultaneous extraction of metals and recycling of waste. This paper describes a study of a technology for recycling aluminum slag from foundries to produce secondary aluminum alloy and regenerated flux. Research and processing methods include X-ray phase and spectral analysis of slag composition, multi-stage grinding in a jaw crusher and planetary mill, screening for fraction separation, and selective dissolution of the oxide–salt phase in water or hydrochloric acid followed by filtration and evaporation; obtaining regenerated flux based on phase diagrams of chloride systems; and briquetting and remelting of the extracted aluminum. The technology ensures the extraction of up to 85% of the metallic aluminum from slag and the production of regenerated flux based on the NaCl–KCl–MgCl2 system with a low melting point.
Open AccessMultistage Recycling of Aluminum Casting Slags: Metal Extraction and Salt Flux Regeneration
The depletion of natural resources remains an acute global problem, highlighting the importance of developing sustainable technologies that enable the simultaneous extraction of metals and recycling of waste. This paper describes a study of a technology for recycling aluminum slag from foundries to produce secondary aluminum alloy and regenerated flux. Research and processing methods include X-ray phase and spectral analysis of slag composition, multi-stage grinding in a jaw crusher and planetary mill, screening for fraction separation, and selective dissolution of the oxide–salt phase in water or hydrochloric acid followed by filtration and evaporation; obtaining regenerated flux based on phase diagrams of chloride systems; and briquetting and remelting of the extracted aluminum. The technology ensures the extraction of up to 85% of the metallic aluminum from slag and the production of regenerated flux based on the NaCl–KCl–MgCl2 system with a low melting point.
- 30 June 2025
- Published by Ore and Metals Publishing House in Non-ferrous Metals
- No. 1,p. 62-69
Study of structure and properties of industrial ingot made of alloy 1580 and determination of its deformability resource during cold rolling
The structure and properties of an industrial large-size ingot of alloy 1580, obtained by semi-continuous casting, have been studied. Evidence has been presented which indicates that the ingot exhibits a fine crystalline structure and is devoid of primary intermetallides Al3(Sc, Zr). The phase composition of the ingot subsequent to annealing has been ascertained. The present study investigates the modes of hot and cold rolling of the ingot to obtain 1 mm thick sheets. The structure of the resulting sheets, after undergoing the process of annealing, has been shown to represent elongated fibres of grains. These are characterised by the presence of dispersed inclusions of excess phases along their boundaries. It has been established that, upon subjecting sheets to annealing temperatures of 225, 250 and 275 °C, a fibrous structure is observed in the absence of any indications of recrystallisation. However, at an annealing temperature of 300 °C, the presence of single recrystallized grains is detected within the structure. Furthermore, at an annealing temperature of 350 °C, the formation of a recrystallized structure is promoted throughout the volume of the sheet. The graphs presented herein illustrate the dependence of the mechanical properties of annealed cold-rolled sheets on the annealing temperature. The investigation revealed that the plasticity resource of hot-rolled sheets from alloy 1580 is approximately 80% when subjected to cold rolling. The study was supported by the Russian Science Foundation (project № 25-19-20133, https://rscf.ru/project/25-19-20133/), and the Krasnoyarsk Regional Science Foundation.
- 30 June 2025
- Published by Ore and Metals Publishing House in Non-ferrous Metals
- No. 1,p. 62-69
Study of structure and properties of industrial ingot made of alloy 1580 and determination of its deformability resource during cold rolling
The structure and properties of an industrial large-size ingot of alloy 1580, obtained by semi-continuous casting, have been studied. Evidence has been presented which indicates that the ingot exhibits a fine crystalline structure and is devoid of primary intermetallides Al3(Sc, Zr). The phase composition of the ingot subsequent to annealing has been ascertained. The present study investigates the modes of hot and cold rolling of the ingot to obtain 1 mm thick sheets. The structure of the resulting sheets, after undergoing the process of annealing, has been shown to represent elongated fibres of grains. These are characterised by the presence of dispersed inclusions of excess phases along their boundaries. It has been established that, upon subjecting sheets to annealing temperatures of 225, 250 and 275 °C, a fibrous structure is observed in the absence of any indications of recrystallisation. However, at an annealing temperature of 300 °C, the presence of single recrystallized grains is detected within the structure. Furthermore, at an annealing temperature of 350 °C, the formation of a recrystallized structure is promoted throughout the volume of the sheet. The graphs presented herein illustrate the dependence of the mechanical properties of annealed cold-rolled sheets on the annealing temperature. The investigation revealed that the plasticity resource of hot-rolled sheets from alloy 1580 is approximately 80% when subjected to cold rolling. The study was supported by the Russian Science Foundation (project № 25-19-20133, https://rscf.ru/project/25-19-20133/), and the Krasnoyarsk Regional Science Foundation.
- Open Access
Analysis of Composition, Properties, and Usage Efficiency of Different Commercial Salt Fluxes for Aluminum Alloy Refining
One of the key problems in the billet and shaped casting of aluminum alloys is the presence of various undesirable inclusions and impurities in the melt, which can serve as stress concentrators in the finished product, as well as dissolved hydrogen, which contributes to the formation of porosity. The interaction of aluminum with other gases produced by the combustion of fuel particles, oil, and paint materials brought into the furnace together with charge and scrap increases the amount of nitrides, oxides, carbides, and sulfides in the melt. Flux treatment is widely used as protection of aluminum alloys from oxidation and removal of impurities. The present paper reports the data of a comparative analysis of five widely used flux compositions based on sodium, potassium, and magnesium chlorides. The study covers the following aspects: chemical composition, moisture content, melting temperature and melting range, particle size distribution, and refining ability as measured by the change in Na, Ca, and H2 content after melt treatment.
Open AccessAnalysis of Composition, Properties, and Usage Efficiency of Different Commercial Salt Fluxes for Aluminum Alloy Refining
One of the key problems in the billet and shaped casting of aluminum alloys is the presence of various undesirable inclusions and impurities in the melt, which can serve as stress concentrators in the finished product, as well as dissolved hydrogen, which contributes to the formation of porosity. The interaction of aluminum with other gases produced by the combustion of fuel particles, oil, and paint materials brought into the furnace together with charge and scrap increases the amount of nitrides, oxides, carbides, and sulfides in the melt. Flux treatment is widely used as protection of aluminum alloys from oxidation and removal of impurities. The present paper reports the data of a comparative analysis of five widely used flux compositions based on sodium, potassium, and magnesium chlorides. The study covers the following aspects: chemical composition, moisture content, melting temperature and melting range, particle size distribution, and refining ability as measured by the change in Na, Ca, and H2 content after melt treatment.
- 1 March 2025
- Published by Springer Nature in Metallurgist
- Vol. 68 (11) , 1688-1701
Study of the properties of refining fluxes and assessment of their effectiveness for removing impurities from alloy 1580 ingots
- 1 March 2025
- Published by Springer Nature in Metallurgist
- Vol. 68 (11) , 1688-1701
Study of the properties of refining fluxes and assessment of their effectiveness for removing impurities from alloy 1580 ingots
- 11 December 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (8) , 1231-1239
Study of deformability during the rolling of aluminum alloy 1580 doped with small additions of erbium and ytterbium
- 11 December 2024
- Published by Springer Nature in Metallurgist
- Vol. 68 (8) , 1231-1239
Study of deformability during the rolling of aluminum alloy 1580 doped with small additions of erbium and ytterbium
- 6 December 2024
- Published by Ore and Metals Publishing House in Non-ferrous Metals
- No. 2,p. 69-74
Investigation of structure and properties of the welded joint obtained by friction stir welding of 1580 alloy hot-rolled sheets
The weldability of hot-rolled sheets of alloy 1580 by friction stir welding was investigated. The test blanks were cutfrom 6.0 mm thick sheets, which were produced under industrial conditions by hot rolling of large-size ingots with dimensions of 300×1445×2200 mm at the “SGP Kvarto 2800” mill. Cards of 210×297 mm size were cut from the sheets and then roasted under two regimes: at 300 °C for three hours and at 350 °C for three hours. The work solved the problems of determining the mechanical properties of welded samples by tensile tests, investigating the structure of the weld by metallographic and electron microscopic methods, assessing the quality of the weld by radiographic analysis and technological tests for static bending. It has been established that the use of the friction stir welding method for joining 1580 alloy sheets allows to obtain high quality of the welded seam. Mechanical tests have shown that the strength of welded joints obtained by the FSW method is almost at the level of the base metal strength and does not depend on the localization of the fracture point. The samples after welding withstood bending tests without cracks along the entire length of the weld, both by bending at an angle of 150° with a mandrel, and after continued testing by static bending in a vise to parallelism of the sides. The work was carried out by the laboratory of low-carbon metallurgy and power engineering within the framework of the state assignment of “Siberian Federal University” of the organization-participant of REC “Yenisei Siberia” within the framework of the national project “Science and Universities”, project number FSRZ-2024-0004.
- 6 December 2024
- Published by Ore and Metals Publishing House in Non-ferrous Metals
- No. 2,p. 69-74
Investigation of structure and properties of the welded joint obtained by friction stir welding of 1580 alloy hot-rolled sheets
The weldability of hot-rolled sheets of alloy 1580 by friction stir welding was investigated. The test blanks were cutfrom 6.0 mm thick sheets, which were produced under industrial conditions by hot rolling of large-size ingots with dimensions of 300×1445×2200 mm at the “SGP Kvarto 2800” mill. Cards of 210×297 mm size were cut from the sheets and then roasted under two regimes: at 300 °C for three hours and at 350 °C for three hours. The work solved the problems of determining the mechanical properties of welded samples by tensile tests, investigating the structure of the weld by metallographic and electron microscopic methods, assessing the quality of the weld by radiographic analysis and technological tests for static bending. It has been established that the use of the friction stir welding method for joining 1580 alloy sheets allows to obtain high quality of the welded seam. Mechanical tests have shown that the strength of welded joints obtained by the FSW method is almost at the level of the base metal strength and does not depend on the localization of the fracture point. The samples after welding withstood bending tests without cracks along the entire length of the weld, both by bending at an angle of 150° with a mandrel, and after continued testing by static bending in a vise to parallelism of the sides. The work was carried out by the laboratory of low-carbon metallurgy and power engineering within the framework of the state assignment of “Siberian Federal University” of the organization-participant of REC “Yenisei Siberia” within the framework of the national project “Science and Universities”, project number FSRZ-2024-0004.
- 1 March 2024
- Published by Springer Nature in Metallurgist
- Vol. 67 (11-12) , 1791-1801
Simulating the process of aluminum alloy ingots crystallization in semi-continuous casting
- 1 March 2024
- Published by Springer Nature in Metallurgist
- Vol. 67 (11-12) , 1791-1801
Simulating the process of aluminum alloy ingots crystallization in semi-continuous casting
- 1 November 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (7-8) , 1166-1177
A Comparative Analysis of Technologies for Producing Al–3Ti–1B Modifying Master Alloy
- 1 November 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (7-8) , 1166-1177
A Comparative Analysis of Technologies for Producing Al–3Ti–1B Modifying Master Alloy
- 1 September 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (5-6) , 757-767
Study of Industrial Aluminum Alloy 1580 Sheet Corrosion Resistance
- 1 September 2023
- Published by Springer Nature in Metallurgist
- Vol. 67 (5-6) , 757-767
Study of Industrial Aluminum Alloy 1580 Sheet Corrosion Resistance