Hanqiang Wu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Hanqiang Wu has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Yongbo Wu
Department of Mechanical and Energy Engineering, Southern University of Science and Technology, Shenzhen, China
5 shared publications - Jiang Zeng
Southern University of Science and Technology, Shenzhen, China
4 shared publications - Jiaping Qiao
Harbin Institute of Technology, Harbin, China
3 shared publications - Ming Feng
College of Mechanical and Electrical Engineering, Wenzhou University, Wenzhou 325035, China
3 shared publications - Shibo Zhang
Multifield Ultrasonic Equipment (Jiangxi) Co., Ltd., Fuzhou 344000, China; ShenZhen Vibrosurgery Instrument Co., Ltd., Shenzhen 518000, China
2 shared publications - Sisi Li
College of Mechanical and Electrical Engineering, Wenzhou University, Wenzhou 325035, China
2 shared publications
Latest Publications
- 1 January 2024
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 60 (9) , 13-25
Fundamental Research on the Ultrasonic Assisted Plasma Oxidation Modification Grinding of Titanium Alloy
- 1 January 2024
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 60 (9) , 13-25
Fundamental Research on the Ultrasonic Assisted Plasma Oxidation Modification Grinding of Titanium Alloy
- Open Access
- 12 September 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (9) , 397
Reducing Wheel Loading in the Grinding of Titanium Alloys through Ultrasonic-Assisted Plasma Oxidation Modification
To reduce wheel loading caused by chip adhesion in the grinding of titanium alloys, a new method named ultrasonic-assisted plasma oxidation modification grinding is suggested. The processing principle was introduced in this research, and based on that, the experimental apparatus was established. Then, the surface and cross-sectional morphologies of a workpiece with an oxide layer were characterized, followed by the detection of its microhardness and surface composition. On this basis, in the absence and presence of the oxide layer, the dynamic changes in wheel loading on the grinding wheel surface and the evolution behavior of chip adhesion on the grains were both investigated after gradually increasing the grinding passes. Finally, the effects of wheel loading on the ground surface morphologies were analyzed. The results showed that the oxide layer with low microhardness was mainly composed of TiO2 and Al2O3. Moreover, with an increase in grinding passes, the overall occupied area of chip adhesion on the grinding wheel surface increased proportionally in the absence of the oxide layer, which finally caused severe wheel loading. Conversely, yet at almost the same rate, the overall occupied area of chip adhesion increased after remaining comparatively unchanged in a short range of grinding passes in the presence of the oxide layer, which effectively inhibited the wheel loading. Compared with the ground surface obtained without an oxide layer, the generation of plastic-stacking was significantly restrained with the assistance of the oxide layer, thereby improving the ground surface quality.
- 12 September 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (9) , 397
Open AccessReducing Wheel Loading in the Grinding of Titanium Alloys through Ultrasonic-Assisted Plasma Oxidation Modification
To reduce wheel loading caused by chip adhesion in the grinding of titanium alloys, a new method named ultrasonic-assisted plasma oxidation modification grinding is suggested. The processing principle was introduced in this research, and based on that, the experimental apparatus was established. Then, the surface and cross-sectional morphologies of a workpiece with an oxide layer were characterized, followed by the detection of its microhardness and surface composition. On this basis, in the absence and presence of the oxide layer, the dynamic changes in wheel loading on the grinding wheel surface and the evolution behavior of chip adhesion on the grains were both investigated after gradually increasing the grinding passes. Finally, the effects of wheel loading on the ground surface morphologies were analyzed. The results showed that the oxide layer with low microhardness was mainly composed of TiO2 and Al2O3. Moreover, with an increase in grinding passes, the overall occupied area of chip adhesion on the grinding wheel surface increased proportionally in the absence of the oxide layer, which finally caused severe wheel loading. Conversely, yet at almost the same rate, the overall occupied area of chip adhesion increased after remaining comparatively unchanged in a short range of grinding passes in the presence of the oxide layer, which effectively inhibited the wheel loading. Compared with the ground surface obtained without an oxide layer, the generation of plastic-stacking was significantly restrained with the assistance of the oxide layer, thereby improving the ground surface quality.
- 20 February 2023
- Published by Elsevier in Ultrasonics
- Vol. 131, 106966
Bone cutting processes and removal behaviors in orthopedic surgery with an ultrasonic orthopedic scalpel
- 20 February 2023
- Published by Elsevier in Ultrasonics
- Vol. 131, 106966
Bone cutting processes and removal behaviors in orthopedic surgery with an ultrasonic orthopedic scalpel
- 2 June 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (3-4) , 1717-1730
Experimental investigation on ultrasonic-assisted truing/dressing of diamond grinding wheel with cup-shaped GC wheel
- 2 June 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (3-4) , 1717-1730
Experimental investigation on ultrasonic-assisted truing/dressing of diamond grinding wheel with cup-shaped GC wheel
- 23 September 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 118 (5-6) , 1859-1872
Experimental study on the effect of grinding path in tangential ultrasonic-assisted grinding for the curved surfaces of zirconia ceramics
- 23 September 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 118 (5-6) , 1859-1872
Experimental study on the effect of grinding path in tangential ultrasonic-assisted grinding for the curved surfaces of zirconia ceramics
- 5 April 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 114 (7-8) , 2045-2054
Improving the grindability of Inconel 718 by hydrogen embrittlement in ultrasonic-assisted grinding
- 5 April 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 114 (7-8) , 2045-2054
Improving the grindability of Inconel 718 by hydrogen embrittlement in ultrasonic-assisted grinding