Tyler Steiner
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Tyler Steiner has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Drew M. Miles
California Institute of Technology, Cahill Center for Astrophysics, Pasadena, California, United States
4 shared publications - Jake A. McCoy
The Pennsylvania State Univ. (United States)
4 shared publications - Richard Howard
Oak Ridge National Laboratory (ORNL), Oak Ridge, TN (United States). High Flux Isotope Reactor (HFIR)
3 shared publications Benjamin D. Donovan
Pennsylvania State University, University Park, Department of Astronomy and Astrophysics, Pennsylvan
2 shared publicationsChad M. Eichfeld
Pennsylvania State University, University Park, Department of Astronomy and Astrophysics, Pennsylvan
2 shared publicationsChristopher R. Hillman
The Pennsylvania State Univ. (United States)
2 shared publications
Latest Publications
- 8 July 2022
- Published by Taylor & Francis in Nuclear Technology
- Vol. 208 (11) , 1745-1755
Systematic Component Investigation of the Steady-State High-Temperature In-Pile Nuclear Thermal Propulsion Experimental Test Bed
A high-temperature, steady-state, in-pile experiment was developed to simulate prototypical nuclear thermal propulsion conditions. The experimental development of the resistively heated test apparatus involved spatially scaling the device to a larger heated region from a previous smaller out-of-pile prototype. A series of tests and investigations were conducted to replicate the smaller out-of-pile system’s success of achieving 2500 K. However, limitations within the larger assembly were identified; specifically, the heater filament design does not scale well. The larger assembly can reliably generate usable temperature levels from room temperature up to those exceeding 1300 K for hours. It can briefly sustain a usable 1800 K. The larger system is achieving temperatures over 2500 K, but these are localized and unable to be monitored in the current design. The achieved temperature levels remain suitable for testing various components considered for a nuclear thermal rocket. However, due to the limitations of the current heater filament, it is recommended that the apparatus be redesigned to utilize a rigid heating element similar to that used during the Radioisotope Propulsion Technology Program (Project POODLE) in the 1960s.
- 8 July 2022
- Published by Taylor & Francis in Nuclear Technology
- Vol. 208 (11) , 1745-1755
Systematic Component Investigation of the Steady-State High-Temperature In-Pile Nuclear Thermal Propulsion Experimental Test Bed
A high-temperature, steady-state, in-pile experiment was developed to simulate prototypical nuclear thermal propulsion conditions. The experimental development of the resistively heated test apparatus involved spatially scaling the device to a larger heated region from a previous smaller out-of-pile prototype. A series of tests and investigations were conducted to replicate the smaller out-of-pile system’s success of achieving 2500 K. However, limitations within the larger assembly were identified; specifically, the heater filament design does not scale well. The larger assembly can reliably generate usable temperature levels from room temperature up to those exceeding 1300 K for hours. It can briefly sustain a usable 1800 K. The larger system is achieving temperatures over 2500 K, but these are localized and unable to be monitored in the current design. The achieved temperature levels remain suitable for testing various components considered for a nuclear thermal rocket. However, due to the limitations of the current heater filament, it is recommended that the apparatus be redesigned to utilize a rigid heating element similar to that used during the Radioisotope Propulsion Technology Program (Project POODLE) in the 1960s.
- Open Access
- 15 February 2022
- Published by Taylor & Francis in Nuclear Technology
- Vol. 208 (sup1) , S74-S84
Steady-State Irradiation of Characterized Instruments for Nuclear Thermal Rockets Using In-Pile Experiment Apparatus
The development of nuclear rocket technology is critical for further exploration of extra-terrestrial bodies. Nuclear rockets can provide various advantages over current chemical rockets. However, the harsh environment provides several challenges regarding instrument performance. Temperature extremes, radiation (reactor and space), and the inability to conduct traditional maintenance activities can lead to severe degradation in instrument performance. To better understand the effects of radiation on instrumentation, an irradiation campaign has been designed to test a set of instruments provided by a collaborator in the aerospace industry. Details concerning instrument performance before and after irradiation are provided to allow for an analysis of the tested instruments. Additionally, the design of the irradiation test is described in detail.
- 15 February 2022
- Published by Taylor & Francis in Nuclear Technology
- Vol. 208 (sup1) , S74-S84
Open AccessSteady-State Irradiation of Characterized Instruments for Nuclear Thermal Rockets Using In-Pile Experiment Apparatus
The development of nuclear rocket technology is critical for further exploration of extra-terrestrial bodies. Nuclear rockets can provide various advantages over current chemical rockets. However, the harsh environment provides several challenges regarding instrument performance. Temperature extremes, radiation (reactor and space), and the inability to conduct traditional maintenance activities can lead to severe degradation in instrument performance. To better understand the effects of radiation on instrumentation, an irradiation campaign has been designed to test a set of instruments provided by a collaborator in the aerospace industry. Details concerning instrument performance before and after irradiation are provided to allow for an analysis of the tested instruments. Additionally, the design of the irradiation test is described in detail.
- 7 April 2021
- Published by Taylor & Francis in Nuclear Technology
- Vol. 208 (1) , 100-114
Steady-State In-Pile Nuclear Thermal Propulsion Experimental Testbed Initial Demonstration at The Ohio State University Research Reactor
Nuclear thermal propulsion (NTP) demonstrated a reported technology readiness level of 5 during the work performed in the 1950s–1970s under the Rover program. This level of capability was achieved through the design, construction, and use of 22 experimental ground tests. These experiments served as testbeds for designs, materials, and instrumentation at prototypical NTP conditions. To continue the investigation into NTP system materials, components, and fuels, a modern experimental testbed has been designed and implemented. A steady-state, high-temperature, subscale, in-pile testbed has been developed to continue this investigation. The In-Pile Experiment Set Apparatus (INSET) has demonstrated that it can be used to test samples under two NTP prototypical environmental factors: temperature and neutron fluence. The demonstration using The Ohio State University Research Reactor is presented here. This demonstration required INSET to maintain a thermal environment below 1070 K for 15 min during a 5-h irradiation to achieve a neutron fluence around 1017 n/cm2.
- 7 April 2021
- Published by Taylor & Francis in Nuclear Technology
- Vol. 208 (1) , 100-114
Steady-State In-Pile Nuclear Thermal Propulsion Experimental Testbed Initial Demonstration at The Ohio State University Research Reactor
Nuclear thermal propulsion (NTP) demonstrated a reported technology readiness level of 5 during the work performed in the 1950s–1970s under the Rover program. This level of capability was achieved through the design, construction, and use of 22 experimental ground tests. These experiments served as testbeds for designs, materials, and instrumentation at prototypical NTP conditions. To continue the investigation into NTP system materials, components, and fuels, a modern experimental testbed has been designed and implemented. A steady-state, high-temperature, subscale, in-pile testbed has been developed to continue this investigation. The In-Pile Experiment Set Apparatus (INSET) has demonstrated that it can be used to test samples under two NTP prototypical environmental factors: temperature and neutron fluence. The demonstration using The Ohio State University Research Reactor is presented here. This demonstration required INSET to maintain a thermal environment below 1070 K for 15 min during a 5-h irradiation to achieve a neutron fluence around 1017 n/cm2.
- 1 October 2020
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 367
Assessment of near-term fuel screening and qualification needs for nuclear thermal propulsion systems
- 1 October 2020
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 367
Assessment of near-term fuel screening and qualification needs for nuclear thermal propulsion systems
- Open Access
- 29 October 2019
- Published by SPIE-Intl Soc Optical Eng in Journal of Astronomical Telescopes, Instruments, and Systems
- Vol. 5 (04) , 044006-11
Water Recovery X-Ray Rocket grating spectrometer
The Water Recovery X-Ray Rocket (WRXR) was a suborbital rocket payload that launched from the Kwajalein Atoll on April 4, 2018. The WRXR was a technology-driven astrophysics payload that sought to demonstrate the performance of two technologies assigned the highest priority to NASA Astrophysics technology development in the 2019 Astrophysics Biennial Technology Report:1 x-ray reflection gratings and an x-ray hybrid CMOS detector (HCD). Both technologies were studied or are actively under development for the Lynx flagship mission concept,2 – 4 explorer and probe mission concepts,5 – 8 and smaller missions, such as suborbital rocket payloads9,10 and cubesats.11 The WRXR, along with the Colorado High-resolution Echelle Stellar Spectrograph,12 also enabled the first successful demonstrations of NASA water recovery technology for astrophysics suborbital rocket payloads. Further, the WRXR served as a pathfinder for an upcoming rocket-borne diffuse soft x-ray spectrometer that will improve in both effective area and spectral resolving power.
- 29 October 2019
- Published by SPIE-Intl Soc Optical Eng in Journal of Astronomical Telescopes, Instruments, and Systems
- Vol. 5 (04) , 044006-11
Open AccessWater Recovery X-Ray Rocket grating spectrometer
The Water Recovery X-Ray Rocket (WRXR) was a suborbital rocket payload that launched from the Kwajalein Atoll on April 4, 2018. The WRXR was a technology-driven astrophysics payload that sought to demonstrate the performance of two technologies assigned the highest priority to NASA Astrophysics technology development in the 2019 Astrophysics Biennial Technology Report:1 x-ray reflection gratings and an x-ray hybrid CMOS detector (HCD). Both technologies were studied or are actively under development for the Lynx flagship mission concept,2 – 4 explorer and probe mission concepts,5 – 8 and smaller missions, such as suborbital rocket payloads9,10 and cubesats.11 The WRXR, along with the Colorado High-resolution Echelle Stellar Spectrograph,12 also enabled the first successful demonstrations of NASA water recovery technology for astrophysics suborbital rocket payloads. Further, the WRXR served as a pathfinder for an upcoming rocket-borne diffuse soft x-ray spectrometer that will improve in both effective area and spectral resolving power.
- 14 December 2018
- Published by American Astronomical Society in The Astrophysical Journal
- Vol. 869 (2) , 95
Fabrication and Diffraction Efficiency of a Large-format, Replicated X-Ray Reflection Grating
We present the methodology used to fabricate an X-ray reflection grating and describe a technique for grating replication. Further, we present the experimental procedure and results of a study to measure the diffraction efficiency of a replicated X-ray reflection grating in an extreme off-plane geometry. The blazed grating demonstrates a total diffraction efficiency of ∼60% from 0.34 to 1.2 keV at a grazing angle of ∼1.°5, with single-order efficiency ranging from ∼35% to 65% for energies within the blaze envelope. The diffraction efficiency of the grating measured relative to the reflectivity of the metal coating averages ∼90% above 0.34 keV. Data collected as a function of beam position on the grating indicate a relative variation in total efficiency of <1% rms across the grating surface.
- 14 December 2018
- Published by American Astronomical Society in The Astrophysical Journal
- Vol. 869 (2) , 95
Fabrication and Diffraction Efficiency of a Large-format, Replicated X-Ray Reflection Grating
We present the methodology used to fabricate an X-ray reflection grating and describe a technique for grating replication. Further, we present the experimental procedure and results of a study to measure the diffraction efficiency of a replicated X-ray reflection grating in an extreme off-plane geometry. The blazed grating demonstrates a total diffraction efficiency of ∼60% from 0.34 to 1.2 keV at a grazing angle of ∼1.°5, with single-order efficiency ranging from ∼35% to 65% for energies within the blaze envelope. The diffraction efficiency of the grating measured relative to the reflectivity of the metal coating averages ∼90% above 0.34 keV. Data collected as a function of beam position on the grating indicate a relative variation in total efficiency of <1% rms across the grating surface.
- 6 July 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10699, 235
Grating design for the Water Recovery X-ray Rocket
The Water Recovery X-ray Rocket (WRXR) is a sounding rocket payload that launched from the Kwajalein Atoll in April 2018 and was the first NASA astrophysics sounding rocket payload to be recovered from water. WRXR's primary instrument is a grating spectrometer that consists of a mechanical collimator, X-ray reflection gratings, grazing-incidence mirrors, and a hybrid CMOS detector. We present here the design of the WRXR spectrometer’s gratings and mirrors.
- 6 July 2018
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10699, 235
Grating design for the Water Recovery X-ray Rocket
The Water Recovery X-ray Rocket (WRXR) is a sounding rocket payload that launched from the Kwajalein Atoll in April 2018 and was the first NASA astrophysics sounding rocket payload to be recovered from water. WRXR's primary instrument is a grating spectrometer that consists of a mechanical collimator, X-ray reflection gratings, grazing-incidence mirrors, and a hybrid CMOS detector. We present here the design of the WRXR spectrometer’s gratings and mirrors.
- 29 August 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 28
An introduction to the water recovery x-ray rocket
- 29 August 2017
- Published by SPIE-Intl Soc Optical Eng
- p. 28
An introduction to the water recovery x-ray rocket