GLGangda Liang

Gangda Liang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Gangda Liang has a total of 20 co-authors. Here are the top co-authors by number of shared publications:

  • Dayong Ning

    Naval Architecture and Ocean Engineering College, Dalian Maritime University, Dalian 116026, China

    2 shared publications
  • Jiaoyi Hou

    Naval Architecture and Ocean Engineering College, Dalian Maritime University, Dalian 116026, China

    2 shared publications
  • Dayong Ning

    School of Naval Architecture and Ocean Engineering Dalian Maritime University Dalian Liaoning China

    1 shared publication
  • Dayong Ning

    National Center for International Research of Subsea Engineering Technology and Equipment, Dalian Maritime University, Dalian 116026, China

    1 shared publication
  • Dejin Cai

    School of Naval Architecture and Ocean Engineering Dalian Maritime University Dalian Liaoning China

    1 shared publication
  • Fengrui Zhang

    School of Naval Architecture and Ocean Engineering Dalian Maritime University Dalian Liaoning China

    1 shared publication

Latest Publications

  • Design and Optimization of a Deep Sea Bionic Robot Fish Based on Phase Change Actuator

    by Gangda Liang, Dayong Ning, Zhilei Liu, Fengrui Zhang, Ming Yi, Dejin Cai, Lincong Lan, Jiaoyi Hou

    In this study, a bionic fin drive system suitable for deep‐sea environments is proposed. The system heats the phase change material (PCM) through the heat‐conducting medium and converts the expansion generated during the phase change process into hydraulic energy. Finally, the tail fin swing and pectoral fin expansion are realized through a novel motion conversion device, which offers the advantages of simple structure and low cost. In addition, the effects of the heat transfer medium and the thickness of the fish body outside the phase change actuator (PCA) on the output performance of the fin PCA were analyzed. The flexible adjustment of the tail fin's swinging characteristics can be realized by adjusting the voltage and duty cycle applied to the PCA heating sheet. A bionic fish prototype equipped with a phase‐change drive system has been successfully fabricated. The experimental results indicate that the robot can swim straight at a speed of 36 mm/s and complete a quick turn with a radius of 3.2 BL. Through the simulation of deep‐sea environment experiments, the robot can still achieve flexible underwater movement under water pressure of up to 110 MPa without bulky pressure‐resistant devices. These excellent performances demonstrate the reliable movement ability of the bionic robotic fish in the extreme deep‐sea environment.

  • Design and Fabrication of a Compact Waterjet Thruster for Deep-Sea Applications

    by Ning Dayong, Liangjia Wang, Liang Gangda, Zhilei Liu, Wang Jinhui, Jiaoyi Hou

    In the context of the growing demand for compact equipment in deep-sea exploration missions, the development of lightweight propulsion systems is confronted with considerable challenges. In view of the necessity to resist high pressure, the design of deep-sea thrusters generally incorporates a bulky configuration. To address this technical bottleneck, this study proposes a novel compact deep-sea thruster based on electromagnetic soft-coupled actuation. The thruster comprises a body support structure, an electromagnetic drive mechanism, and a soft-bodied water bladder. The mechanism in question generates periodic propulsion forces by altering the volume of the bladder in response to pulsed electrical signals. This study investigates the propulsion force and operational cycles of the thruster under varying structural parameters and control currents. A pressure tank is employed to validate the thruster’s pressure resistance, and two typical operational configurations are designed to test its propulsion effectiveness. The findings indicate that the thruster functions reliably at depths in excess of 11 000 m. It has been demonstrated that the two typical configurations are capable of attaining swimming speeds of 92.7 mm/s (1.55 BL/s) and 68.2 mm/s (1.17 BL/s), respectively, thereby demonstrating exceptional propulsion capabilities.

  • Open Access

    Lightweight Robotic Joint with Thermally Activated Paraffin Actuator in the Deep Sea

    by Dayong Ning, Xiaokang He, Jiaoyi Hou, Gangda Liang, Kang Zhang

    The abundance of resources in the deep sea continues to inspire mankind’s desire for exploration. However, the extreme environments pose a huge challenge for designing deep-sea mechanical devices that are primarily driven by hydraulic and electric motor technology. Researchers are beginning to explore more flexible and innovative drive methods suitable for the deep-sea environment. This paper presents a simple joint mechanism based on a paraffin phase change thermal expansion drive. Its unique design combines a flexible cell with an open structure that allows it to adapt to different pressures at different water depths. Paraffin is enclosed in multiple sets of smaller paraffin cells, which act as thermal expansion material for generating hydraulic pressure. The software comsol was used to perform a finite element analysis of the phase change process in paraffin. By fabricating the mechanical structure, the displacement generated by the thermal expansion is amplified and converted, thus enabling a bi-directional rotational displacement output from the joint while reducing the complexity of the structure. The joints in this paper provide a reliable reference for the design of small deep-sea robot drive systems.


  • Open Access

    Design and Performance Study for Electrothermally Deep-Sea Drive Microunits Using a Paraffin Phase Change Material

    by Dayong Ning, Zihao Li, Gangda Liang, Qibo Wang, Weifeng Zou, Yongjun Gong, Jiaoyi Hou

    Considering the further exploration of the ocean, the requirements for deep-sea operation equipment have increased. Many problems existing in the widely used deep-sea hydraulic system have become increasingly prominent. Compared with the traditional deep-sea hydraulic system, actuators using a paraffin phase change material (PCM) have incomparable advantages, including lightweight structure, low energy consumption, high adaptability to the deep sea, and good biocompatibility. Thus, a deep-sea drive microunit (DDM) based on paraffin PCM is proposed in this paper. The device adopts a flexible shell, adapting to the high-pressure environment of the deep-sea based on the principle of pressure compensation. The device realizes the output of displacement and force through the electrothermal drive, which can be used as actuator or power source of other underwater operation equipment. The microunit successfully completes the functional verification experiments in air, shallow water, and hydrostatic pressure of 110 MPa. In accordance with experimental results, a reasonable control curve is fitted, highlighting its potential application in deep-sea micro electro mechanical systems, especially in underwater soft robot.