Ma. De Los Ángeles Enríquez Pérez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ma. De Los Ángeles Enríquez Pérez has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Víctor Hugo Castrejón-Sánchez
Tecnológico de Estudios Superiores de Jocotitlán
5 shared publications Jaime Rosales-Davalos
Tecnológico de Estudios Superiores de Jocotitlán
3 shared publications- Nidia García-González
Tecnológico de Estudios Superiores de Jocotitlán
3 shared publications - Jaime Rosales Davalos
Tecnológico de Estudios Superiores de Jocotitlán, TecNM
2 shared publications - Abraham Garcia Rodriguez
Tecnológico de Estudios Superiores de Jocotitlán, TecNM
1 shared publication - Dulce D Sánchez-Montiel1 shared publication
Latest Publications
- 30 December 2026
- Published by ECORFAN
- p. 90-106
Hall methodology for Carbon-based/ZnO composite synthesis and it characterization
Currently, new materials are being developed to remove contaminants from wastewater by combining materials to improve their individual properties. This chapter describes the production of the zinc oxide (ZnO) and carbon composite. The ZnO was synthesized by electrolysis, adding Spend Coffee Grounds (SCG) to the electrolytic medium, and finally calcined at 400 °C for 30 min. ZnO, carbon, and the composite were synthesized and characterized. Scanning Electron Microscopy found that ZnO deposits in the pores of the carbon; Infrared Spectroscopy identified bonds associated with carbon and ZnO; X Ray Diffraction yielded a diffractogram with lower intensity compared to that of ZnO (JPDS-361451), due to the synthesis of amorphous carbon; μ-RAMAN Spectroscopy detected characteristic bonds of both materials; finally, the isoelectric point of the composite is 7.3, which will allows working with sorption in neutral systems.
- 30 December 2026
- Published by ECORFAN
- p. 90-106
Hall methodology for Carbon-based/ZnO composite synthesis and it characterization
Currently, new materials are being developed to remove contaminants from wastewater by combining materials to improve their individual properties. This chapter describes the production of the zinc oxide (ZnO) and carbon composite. The ZnO was synthesized by electrolysis, adding Spend Coffee Grounds (SCG) to the electrolytic medium, and finally calcined at 400 °C for 30 min. ZnO, carbon, and the composite were synthesized and characterized. Scanning Electron Microscopy found that ZnO deposits in the pores of the carbon; Infrared Spectroscopy identified bonds associated with carbon and ZnO; X Ray Diffraction yielded a diffractogram with lower intensity compared to that of ZnO (JPDS-361451), due to the synthesis of amorphous carbon; μ-RAMAN Spectroscopy detected characteristic bonds of both materials; finally, the isoelectric point of the composite is 7.3, which will allows working with sorption in neutral systems.
- Open Access
- 21 May 2025
- Published by Asociacion Latinoamericana para el Avance de la Ciencia in Ciencia Latina Revista Científica Multidisciplinar
- Vol. 9 (3) , 10466-10487
Implementación de un Sistema Fotovoltaico Aislado para la Estación Meteorológica del Tecnológico de Estudios Superiores de Jocotitlán
La dependencia de combustibles fósiles para generar electricidad ha elevado la huella de carbono y los costos energéticos, lo que ha impulsado el desarrollo de energías renovables más limpias, accesibles y eficientes. Una de las principales fuentes de energía renovable es la energía solar, esto es debido a su disponibilidad y a la disminución de los costos en la adquisición de paneles solares, a pesar de los avances tecnológicos el aprovechamiento de la energía solar sigue siendo bajo en comparación con el consumo global de energía. No obstante, su implementación en aplicaciones específicas, como sistemas autónomos y aplicaciones agrícolas ha demostrado ser una solución eficiente tanto en zonas aisladas y/o con acceso limitado a la red eléctrica. Este trabajo plantea el dimensionamiento e implementación de un sistema fotovoltaico autónomo para la estación meteorológica del Tecnológico de Estudios Superiores de Jocotitlán (EMTESJO). El objetivo es garantizar un suministro energético continuo e independiente de la red eléctrica, permitiendo el monitoreo ininterrumpido de las variables meteorológicas que se monitorean a través de la estación. La integración de un sistema fotovoltaico asegurará el funcionamiento óptimo y sostenible de la EMTESJO mediante el uso de energías limpias.
- 21 May 2025
- Published by Asociacion Latinoamericana para el Avance de la Ciencia in Ciencia Latina Revista Científica Multidisciplinar
- Vol. 9 (3) , 10466-10487
Open AccessImplementación de un Sistema Fotovoltaico Aislado para la Estación Meteorológica del Tecnológico de Estudios Superiores de Jocotitlán
La dependencia de combustibles fósiles para generar electricidad ha elevado la huella de carbono y los costos energéticos, lo que ha impulsado el desarrollo de energías renovables más limpias, accesibles y eficientes. Una de las principales fuentes de energía renovable es la energía solar, esto es debido a su disponibilidad y a la disminución de los costos en la adquisición de paneles solares, a pesar de los avances tecnológicos el aprovechamiento de la energía solar sigue siendo bajo en comparación con el consumo global de energía. No obstante, su implementación en aplicaciones específicas, como sistemas autónomos y aplicaciones agrícolas ha demostrado ser una solución eficiente tanto en zonas aisladas y/o con acceso limitado a la red eléctrica. Este trabajo plantea el dimensionamiento e implementación de un sistema fotovoltaico autónomo para la estación meteorológica del Tecnológico de Estudios Superiores de Jocotitlán (EMTESJO). El objetivo es garantizar un suministro energético continuo e independiente de la red eléctrica, permitiendo el monitoreo ininterrumpido de las variables meteorológicas que se monitorean a través de la estación. La integración de un sistema fotovoltaico asegurará el funcionamiento óptimo y sostenible de la EMTESJO mediante el uso de energías limpias.
- Open Access
- 2 April 2025
- Published by Facultad de Ciencias de la Ingenieria y Tecnologia de la UABC in REVISTA DE CIENCIAS TECNOLÓGICAS
- Vol. 8 (2) , 1-11
Evaluación mecánica de composito reforzado con vidrio reciclado para aplicaciones estructurales
El presente trabajo se enfocó en el estudio del vidrio reciclado como refuerzo en losetas de cemento, con el objetivo de evaluar su influencia en las propiedades mecánicas y explorar su viabilidad en la industria de la construcción. Para ello, se fabricaron 4 lotes de losetas por triplicado variando la proporción p/p de vidrio y cemento, L1 es el blanco (proporción 0:1), el tamaño de partícula vario: L2 con 354 µm (proporción 1:4), L3 de 250 µm (proporción 1:5) y L4 con 105 µm (proporción 1:5). Se realizaron ensayos mecánicos a los 7, 14 y 28 días de curado, siguiendo la norma ISO 10545-4:2019(E). Además, se utilizó un esclerómetro para evaluar la resistencia superficial de las probetas según la norma NMX-C-192-ONNCCE-2018. Los resultados mostraron que, aunque la incorporación de vidrio permitió obtener una matriz más homogénea y estética, la resistencia mecánica de las losetas fue inferior a la de losetas comerciales con tratamiento térmico. La mezcla con partículas de 250 µm (L3) presentó una mayor resistencia a la flexión, alcanzando 0.25 MPa, mientras que la resistencia a la compresión en los cilindros superó los 40 MPa en las probetas L2 y L3 a los 28 días, siguiendo la norma NMX-C-111-ONNCCE-2018. Este estudio evidencia el potencial del vidrio reciclado en la fabricación de losetas, aunque se requieren optimizaciones en la formulación para mejorar su desempeño estructural
- 2 April 2025
- Published by Facultad de Ciencias de la Ingenieria y Tecnologia de la UABC in REVISTA DE CIENCIAS TECNOLÓGICAS
- Vol. 8 (2) , 1-11
Open AccessEvaluación mecánica de composito reforzado con vidrio reciclado para aplicaciones estructurales
El presente trabajo se enfocó en el estudio del vidrio reciclado como refuerzo en losetas de cemento, con el objetivo de evaluar su influencia en las propiedades mecánicas y explorar su viabilidad en la industria de la construcción. Para ello, se fabricaron 4 lotes de losetas por triplicado variando la proporción p/p de vidrio y cemento, L1 es el blanco (proporción 0:1), el tamaño de partícula vario: L2 con 354 µm (proporción 1:4), L3 de 250 µm (proporción 1:5) y L4 con 105 µm (proporción 1:5). Se realizaron ensayos mecánicos a los 7, 14 y 28 días de curado, siguiendo la norma ISO 10545-4:2019(E). Además, se utilizó un esclerómetro para evaluar la resistencia superficial de las probetas según la norma NMX-C-192-ONNCCE-2018. Los resultados mostraron que, aunque la incorporación de vidrio permitió obtener una matriz más homogénea y estética, la resistencia mecánica de las losetas fue inferior a la de losetas comerciales con tratamiento térmico. La mezcla con partículas de 250 µm (L3) presentó una mayor resistencia a la flexión, alcanzando 0.25 MPa, mientras que la resistencia a la compresión en los cilindros superó los 40 MPa en las probetas L2 y L3 a los 28 días, siguiendo la norma NMX-C-111-ONNCCE-2018. Este estudio evidencia el potencial del vidrio reciclado en la fabricación de losetas, aunque se requieren optimizaciones en la formulación para mejorar su desempeño estructural
- Open Access
- 31 December 2024
- Published by ECORFAN in Revista de la Invención Técnica
Comparison of methods for obtaining a hydroxyapatite and zinc oxide composite (HAp/ZnO)
In this work, the synthesis of a composite material based on hydroxyapatite (HAp) and zinc oxide (ZnO) is reported. Two types of synthesis were evaluated, in order to know which of them allows to obtain a homogeneous composite material of HAp and ZnO, since making a composite material implies that two or more compounds must be integrated and do not separated; the HAp will be obtained from eggshell residue, ZnO will be synthesized by Sol-Gel and electrolysis; in the ZnO obtention, the previously synthesized HAp was incorporated and it is followed by a thermal treatment obtain the oxide. To evaluated the incorporation of ZnO with hydroxyapatite, Scanning Electron Microscopy, Elemental Analysis and Mapping by Energy Dispersive Spectrometry, Infrared Spectroscopy Analysis and X-ray Diffraction were performed. These two synthesis methods are aiming to obtain a homogeneous material, establishing a methodology to produce the material composite, as well as improve the photocatalytic properties.
- 31 December 2024
- Published by ECORFAN in Revista de la Invención Técnica
Open AccessComparison of methods for obtaining a hydroxyapatite and zinc oxide composite (HAp/ZnO)
In this work, the synthesis of a composite material based on hydroxyapatite (HAp) and zinc oxide (ZnO) is reported. Two types of synthesis were evaluated, in order to know which of them allows to obtain a homogeneous composite material of HAp and ZnO, since making a composite material implies that two or more compounds must be integrated and do not separated; the HAp will be obtained from eggshell residue, ZnO will be synthesized by Sol-Gel and electrolysis; in the ZnO obtention, the previously synthesized HAp was incorporated and it is followed by a thermal treatment obtain the oxide. To evaluated the incorporation of ZnO with hydroxyapatite, Scanning Electron Microscopy, Elemental Analysis and Mapping by Energy Dispersive Spectrometry, Infrared Spectroscopy Analysis and X-ray Diffraction were performed. These two synthesis methods are aiming to obtain a homogeneous material, establishing a methodology to produce the material composite, as well as improve the photocatalytic properties.
- 30 December 2024
- Published by ECORFAN
- p. 67-83
Obtaining a Zirconium dioxide-based photocatalyst using sol-gel method for turmeric degradation
In this work, the synthesis, characterization, and evaluation of the photocatalytic properties of ZrO₂ are reported, which is used for the photocatalytic degradation of turmeric using UV light. The technique used for the preparation of zirconium dioxide is the sol-gel method. The samples were characterized using energy dispersive spectroscopy (EDS) to determine the chemical composition, and Scanning Electron Microscopy (SEM) was used to study the surface morphology. The chemical composition and crystalline phases present were analyzed with µ-Raman spectroscopy. The identification of crystalline planes was performed through X-Ray Diffraction. The synthesized ZrO₂ is composed solely of Zr and O, with no contaminants detected. No predominant type of morphology was found. Structural analyses revealed the phases present in each sample, which are: monoclinic, tetragonal, and a mixture of phases (monoclinic/tetragonal).
- 30 December 2024
- Published by ECORFAN
- p. 67-83
Obtaining a Zirconium dioxide-based photocatalyst using sol-gel method for turmeric degradation
In this work, the synthesis, characterization, and evaluation of the photocatalytic properties of ZrO₂ are reported, which is used for the photocatalytic degradation of turmeric using UV light. The technique used for the preparation of zirconium dioxide is the sol-gel method. The samples were characterized using energy dispersive spectroscopy (EDS) to determine the chemical composition, and Scanning Electron Microscopy (SEM) was used to study the surface morphology. The chemical composition and crystalline phases present were analyzed with µ-Raman spectroscopy. The identification of crystalline planes was performed through X-Ray Diffraction. The synthesized ZrO₂ is composed solely of Zr and O, with no contaminants detected. No predominant type of morphology was found. Structural analyses revealed the phases present in each sample, which are: monoclinic, tetragonal, and a mixture of phases (monoclinic/tetragonal).
- Open Access
- 22 July 2024
- Published by Asociacion Latinoamericana para el Avance de la Ciencia in Ciencia Latina Revista Científica Multidisciplinar
- Vol. 8 (4) , 10433-10446
Elaboración de Aglomerados Particulados a Partir del Reciclaje de Envases Multicapa Reforzados con PET-PP
El presente trabajo se analiza la proporción ideal para obtener aglomerados particulados, a partir del reciclaje de envases multicapas (contiene 75% de cartón, 20% de polietileno y 5% de aluminio) postconsumo, reforzados con tereftalato de polietileno (PET) y polipropileno (PP), con la finalidad de contribuir a reducir la generación de residuos. La metodología consiste en la limpieza y secado de la materia prima, posteriormente se muele hasta obtener un tamaño de partícula de 3mm aproximadamente; se homogenizan los materiales y finalmente, se realiza un prensado en caliente, durante este proceso el refuerzo se funde, permitiendo una mejor adherencia de los componentes. Para las pruebas físico-mecánicas se usa como referencias la Norma NMX-C-013-1978, ASTM D 1037-12 y NMX-C-036-ONNCCE-2013. Se obtienen aglomerados ligeros duros al tacto, pueden ser cortados y taladrados sin presencia de grietas, son ignífugos, hidrofóbicos y poseen una resistencia de ruptura de (10.83MPa), se comportan como un material dúctil con memoria de forma. Los materiales obtenidos pueden ser utilizados en la construcción de interiores o como soportes catalíticos para la degradación de colorantes orgánicos.
- 22 July 2024
- Published by Asociacion Latinoamericana para el Avance de la Ciencia in Ciencia Latina Revista Científica Multidisciplinar
- Vol. 8 (4) , 10433-10446
Open AccessElaboración de Aglomerados Particulados a Partir del Reciclaje de Envases Multicapa Reforzados con PET-PP
El presente trabajo se analiza la proporción ideal para obtener aglomerados particulados, a partir del reciclaje de envases multicapas (contiene 75% de cartón, 20% de polietileno y 5% de aluminio) postconsumo, reforzados con tereftalato de polietileno (PET) y polipropileno (PP), con la finalidad de contribuir a reducir la generación de residuos. La metodología consiste en la limpieza y secado de la materia prima, posteriormente se muele hasta obtener un tamaño de partícula de 3mm aproximadamente; se homogenizan los materiales y finalmente, se realiza un prensado en caliente, durante este proceso el refuerzo se funde, permitiendo una mejor adherencia de los componentes. Para las pruebas físico-mecánicas se usa como referencias la Norma NMX-C-013-1978, ASTM D 1037-12 y NMX-C-036-ONNCCE-2013. Se obtienen aglomerados ligeros duros al tacto, pueden ser cortados y taladrados sin presencia de grietas, son ignífugos, hidrofóbicos y poseen una resistencia de ruptura de (10.83MPa), se comportan como un material dúctil con memoria de forma. Los materiales obtenidos pueden ser utilizados en la construcción de interiores o como soportes catalíticos para la degradación de colorantes orgánicos.
- Open Access
- 31 December 2021
- Published by ECORFAN in Revista de Desarrollo Urbano y Sustentable
- p. 1-6
Obtaining particulate agglomerates from the recycling of multilayer containers and low density polyethylene
Currently, the interest and the need to innovate new materials through the use of waste materials has grown, which meet similar or improved physical, chemical and mechanical characteristics of the materials they will replace. During the present investigation, Multilayer Containers (EM) and Low Density Polyethylene (LDPE) were collected, particulate agglomerates with different proportions were obtained, the apparent density, water absorption, mass, volume, heat behavior, angle were determined. contact, machining and compression tests. With the objective of evaluating the proportions p / p in the properties. The advantage of the material obtained is that they do not generate waste and are 100% recyclable. The 90:10 ratio is the one that could be used in the construction industry as false walls, with a modulus of rupture of 52.7 N / mm2 and a compressive stress of 32.9 MP, because it can be machined without altering its characteristics. -physical houses; While the 85:15 and 80:20 proportions, since they cannot be machined, could be used as a floating support with a photocatalyst catalyst, due to the fact that these agglomerates have dimensional stability when in contact with water.
- 31 December 2021
- Published by ECORFAN in Revista de Desarrollo Urbano y Sustentable
- p. 1-6
Open AccessObtaining particulate agglomerates from the recycling of multilayer containers and low density polyethylene
Currently, the interest and the need to innovate new materials through the use of waste materials has grown, which meet similar or improved physical, chemical and mechanical characteristics of the materials they will replace. During the present investigation, Multilayer Containers (EM) and Low Density Polyethylene (LDPE) were collected, particulate agglomerates with different proportions were obtained, the apparent density, water absorption, mass, volume, heat behavior, angle were determined. contact, machining and compression tests. With the objective of evaluating the proportions p / p in the properties. The advantage of the material obtained is that they do not generate waste and are 100% recyclable. The 90:10 ratio is the one that could be used in the construction industry as false walls, with a modulus of rupture of 52.7 N / mm2 and a compressive stress of 32.9 MP, because it can be machined without altering its characteristics. -physical houses; While the 85:15 and 80:20 proportions, since they cannot be machined, could be used as a floating support with a photocatalyst catalyst, due to the fact that these agglomerates have dimensional stability when in contact with water.
- Open Access
- 30 September 2019
- Published by ECORFAN in Revista de Ingeniería Eléctrica
- p. 17-21
Sistema de control de temperatura on-off implementado en el proceso de termoformado para elaboración de bloque a partir de envases multicapas
In this work, a temperature control system (SCT) was designed and implemented in the thermoforming process for the manufacture of blocks for wall construction (BCM). The control process in the SCT consists in establishing the reference temperature for the thermoforming and send it to the Mega 2560 microcontroller. This component processes the input signal, obtaining six digital signals that control the surface temperature of each of the external faces of the BCM mold that has a rectangular prism geometry. These signals are sent to the electrical isolation stage where the actuators enable six electrical resistances (200 Watts to 120 Volts). The feedback of the temperature in the control system was made through type-k thermocouples, whose analog signals are compared with the reference signal to regulate the temperature. This project contributes to establish and control the temperature of the resistances, implemented for the thermoforming process, for the elaboration of blocks using multilayer containers.
- 30 September 2019
- Published by ECORFAN in Revista de Ingeniería Eléctrica
- p. 17-21
Open AccessSistema de control de temperatura on-off implementado en el proceso de termoformado para elaboración de bloque a partir de envases multicapas
In this work, a temperature control system (SCT) was designed and implemented in the thermoforming process for the manufacture of blocks for wall construction (BCM). The control process in the SCT consists in establishing the reference temperature for the thermoforming and send it to the Mega 2560 microcontroller. This component processes the input signal, obtaining six digital signals that control the surface temperature of each of the external faces of the BCM mold that has a rectangular prism geometry. These signals are sent to the electrical isolation stage where the actuators enable six electrical resistances (200 Watts to 120 Volts). The feedback of the temperature in the control system was made through type-k thermocouples, whose analog signals are compared with the reference signal to regulate the temperature. This project contributes to establish and control the temperature of the resistances, implemented for the thermoforming process, for the elaboration of blocks using multilayer containers.
- Open Access
- 30 September 2019
- Published by ECORFAN in Revista de Energía Química y Física
- p. 7-13
Elaboración de un fotocatalizador flotante basado en un composito de TiO2/aglomerado para tratamiento de contaminantes orgánicos usando luz solar
Floating photocatalysts have caused interest due to the benefits they provide. For example, the floating support has characteristic lightness and flexibility; while the photocatalyst has the advantage of being able to interact with sunlight without the need of stirring or oxygenation. In this paper, a floating photocatalyst based on a TiO2/ agglomerate composite is evaluated. The agglomerate is made from post-consumer packaging of multilayer containers. The catalyst was prepared by synthesizing of titanium dioxide powders with phase mixture anatase/rutile. The photocatalyst powder was attached to substrate surface using a varnish obtained by dissolving post-consumer polystyrene containers in toluene. The photocatalyst has different phase A-R (Anatase-Rutile) ratios. The approximate size of the nanostructure is 13.29 ± 3.28 nm, calculated using UV-Vis spectroscopy, the bandgap has values ranging from 2.56 eV to 2.90 Ev. The agglomerates have a rupture modulus of 14.95 N/mm2; they are hydrophobic materials and possess dimensional stability against changes in humidity (length) less than 10%, chemical resistance, are flame retardant. The TiO2/agglomerate composite is used for the photocatalytic degradation of a model pollutant (methylene blue) using sunlight.
- 30 September 2019
- Published by ECORFAN in Revista de Energía Química y Física
- p. 7-13
Open AccessElaboración de un fotocatalizador flotante basado en un composito de TiO2/aglomerado para tratamiento de contaminantes orgánicos usando luz solar
Floating photocatalysts have caused interest due to the benefits they provide. For example, the floating support has characteristic lightness and flexibility; while the photocatalyst has the advantage of being able to interact with sunlight without the need of stirring or oxygenation. In this paper, a floating photocatalyst based on a TiO2/ agglomerate composite is evaluated. The agglomerate is made from post-consumer packaging of multilayer containers. The catalyst was prepared by synthesizing of titanium dioxide powders with phase mixture anatase/rutile. The photocatalyst powder was attached to substrate surface using a varnish obtained by dissolving post-consumer polystyrene containers in toluene. The photocatalyst has different phase A-R (Anatase-Rutile) ratios. The approximate size of the nanostructure is 13.29 ± 3.28 nm, calculated using UV-Vis spectroscopy, the bandgap has values ranging from 2.56 eV to 2.90 Ev. The agglomerates have a rupture modulus of 14.95 N/mm2; they are hydrophobic materials and possess dimensional stability against changes in humidity (length) less than 10%, chemical resistance, are flame retardant. The TiO2/agglomerate composite is used for the photocatalytic degradation of a model pollutant (methylene blue) using sunlight.