TMTayseer Maaly

Tayseer Maaly

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Tayseer Maaly has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • EVALUATION OF MICROBIAL BIOFILM ADHESION AND SURFACE MECHANICAL PROPERTIES OF MODIFIED AKASITE WITH TITANIUM DIOXIDE NANOPARTICLES

    by Tayseer Mohamed Maaly, Mahmoud Saad Abdel-Hlim, Mohammed Samir El Nawawy

    Objective: To assess the ability of modified alkasite with TiO2 nanoparticles (NPs) to prevent microbial biofilm adhesion without compromising the color and surface mechanical properties of the new formulations. Materials and Methods: The Powder of TiO2 NPs was added to alkasite powder in ratios of 3, 5 and 7% (w/w). Crystal violet assay (CV) method was used for assessment of microbial biofilm adhesion, micro hardness was measured by Vickers diamond indentor, color changes of the modified alkasite powder were measured by a spectrophotometer, and surface roughness values were recorded using digital microscope. Three dimensional images were taken for all groups. One and two-way ANOVA were used for the statistical analysis, followed by Tukey′s test. Results: Increased the ratio of titanium dioxide nanoparticles added to alkasite significantly decreased microbial biofilm formation without compromising other properties. Conclusion: The alkasite restorative material modified by 7% nano-titania significantly decreased microbial biofilm formation without any effect on the color and mechanical properties.


  • Open Access

    Color Stability of Nano hybrid Composite and Acrylic Denture Teeth Exposed to Different Coloring Solutions

    by Tayseer Maaly, Mahmoud E. El Homossany

    Purpose: This study was conducted to evaluate the effect of different staining solutions on color stability and surface roughness (SR) of Nano hybrid composite and acrylic denture teeth. Materials and Methods: Fifty specimens divided into two main groups. Each group divided into 5 subgroups each of 5 specimens of acrylic and composite teeth were used in this test. Teeth were immersed in four coloring solutions in addition to distilled water. Color measurements were erformed using spectrophotometer. Color change values were determined before and after immersion in the coloring solutions. The CIE L*a*b* color space was used to evaluate color differences. SR values were evaluated before and following the immersion in coloring solutions using a digital microscope. Results: Showed significant color changes of both types of artificial teeth materials upon immersion in tea, coffee, cola, licorice or distilled water. This color change was greater in case of tea and coffee solutions. The least color change values were obtained from specimens immersed in distilled water. SR values were increased for acrylic teeth compared with composite teeth and there were significant statistical differences in surface roughness of all tested materials after immersion in any of the tested solutions. Conclusions: The acrylic denture teeth material is much more subjected to discoloration than the composite denture teeth material. Surface roughness of all tested teeth of both types recorded statistically significant decrease by immersion in staining solutions.


  • Effect of Ultrasonic Scaling on Microleakage of Class V Composite Restorations Bonded With Different Adhesives

    by Ashraf Ibrahim, Tayseer Maaly, Enas Tawfik Enan

    Objectives: The current study was conducted to investigate the influence of ultrasonic scaling on microleakage under composite restorations bonded with 3 different adhesives. Methods: Sixty standerdized class V cavities were prepared in extracted human molars that were divided in to three groups, according to the type of applied adhesive, as follows: Group A: Fuji Bond LC, Glass ionomer (GI) adhesive, Group B: Clearfill S3 Bond, Self-Etch (SE) adhesive and Group C: OptiBond FL, Etch and Rinse (ER) adhesive. After cavity preparation and composite filling, teeth of each group were further divided into scaled and un-scaled subgroups. Teeth were sectioned buccolingually and ‎the gingival margins of the teeth were evaluated and scored for dye penetration to check the microleakage. Results: Scaling caused a significant increase in microleakage scores of SE adhesive. On the other hand, both ER adhesive and GI adhesive showed insignificant change in microleakage scores after exposure to the ultrasonic scaling.Self- Etch adhesive showed the highest mean rank microleakage value (13.7), while GI adhesive had the lowest mean rank microleakage value (12.9) in the scaled group. Significant difference between the scaled (mean rank 13.7) and un-scaled (mean rank 7.3) subgroups was found only with SE adhesive (p = 0.007). On the other hand, insignificant differences (p = 0.06) were noticed between the two subgroups of GI and ER adhesive. Conclusion: Ultrasonic scaling caused significant increase in microleakage of self-etch adhesive ‎bonded restorations. While GI and ER adhevies bonded restorations revealed more resistance to the effect of ultrasonic scaling.

  • Evaluation of 2-methacryloyloxyethyl phosphorylcholine polymer coated polyamide denture base material: Surface Roughness and Candida Albicans adhesion.

    by Tayseer Maaly, Eman Mohamed

    Purpose: To evaluate Candida albicans adhesion and the surface roughness of polyamide denture base material coated with various concentrations of 2-methacryloyloxyethyl phosphorylcholine (MPC) polymer. Materials and Methods: A total of 80 disks polyamide resin specimens were fabricated and divided into 4 groups (n = 20/group). Surfaces of the specimens in three groups were coated with MPC in different concentrations (0.25 mol/L; 0.50 mol/L and 0.75 mol/L), while uncoated specimens were used as control. Surface roughness (SR) was evaluated using a profilometer. Specimens were incubated with C. albicans for 18 h and the number of adhered cells was determined. Statistically, the following tests were done: analysis of variance, Pearson correlation coefficient test, post hoc Tukey test. Results: Upon PMPC coating, surface roughness values were decreased, with a significant difference between different groups. A statistically significant decrease was observed in C. albicans adhesion in parallel with the increase in the MPC polymer concentration. There was no significant difference between 0.50 mol/L and 0.75 mol/L groups in terms of adhesion. These findings indicated that graft polymerization of MPC on polyamide denture base material reduces the adhesion of C. albicans, and may be evaluated as a coating for prevention of denture stomatitis. Conclusion: Coating of removable prosthesis with 0.75 mol/L MPC is suitable to reduce C. albicans adhesion on polyamide denture base.