C. Swaminathan
Research Subjects
C. Swaminathan has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
J. Sarangan
Professor, Department of Mechanical Engineering, National Institute of Technology, Tiruchirappalli, 620 015, India
5 shared publications- A. Hajamaideen
A.V.C. College of Engineering
1 shared publication B. Samuel Michael
Assistant Professor, Department of Mechanical Engineering, Aarupadai Veedu Institute of Technology, Paiyanoor, Chennai, 603 104, India
1 shared publication
Latest Publications
- 26 December 2022
- Published by Springer Nature in International Journal of Environmental Science and Technology
- Vol. 20 (11) , 12427-12436
Effect of aluminum oxide nanoparticles in algae biodiesel blend as a fuel in CRID engine and its performance, emission and combustion aspects
- 26 December 2022
- Published by Springer Nature in International Journal of Environmental Science and Technology
- Vol. 20 (11) , 12427-12436
Effect of aluminum oxide nanoparticles in algae biodiesel blend as a fuel in CRID engine and its performance, emission and combustion aspects
- 12 December 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (2)
Influence of iron oxide nanoparticles with different injection pressures using lotus seed methyl ester biodiesel: an experimental investigation
The present research work explores the utilization of lotus seed methyl ester in a Common rail direct injection diesel engine. It evaluates the performance, combustion aspects, emission features at different injection pressures 210 bar to 240 bar intervals of 10 bar, along with 120 ppm of iron oxide nanoparticle. For this investigation, the B20 blend used as fuel contains 80% diesel and 20% biodiesel (Lotus seed Methyl Ester). The iron oxide nanoparticles were mixed with the fuel using a mechanical homogenizer and ultrasonication. The present work results revealed a reduction in FC by 12.5%, decreased CO by 50%, a decrease in HC by 16.88%, and the reduction of smoke density by 16.51% compared to that of baseline fuel maximum load (5.2 kW). The combined effect of 240 bar injection pressure and 120 ppm of iron oxide nanoparticle gives the best result. Abbreviation: MS; Motor Sprit (Petrol): HSD; High Speed Diesel: AFT; Transportation fuels: ICRA; Investment Information and Credit Rating Agency of India Limited: IONP; Iron Oxide Nano Particles: SFC; Specific Fuel Consumption: LSME; Lotus Seed Methyl Ester: MT; Metric Ton: BTE; Brake Thermal Efficiency: HC; Hydrocarbon: CO; Carbon monoxide: NOx; Nitrogen Oxides: HRR; Rate of Heat Release: BP; Brake Power
- 12 December 2021
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 47 (2)
Influence of iron oxide nanoparticles with different injection pressures using lotus seed methyl ester biodiesel: an experimental investigation
The present research work explores the utilization of lotus seed methyl ester in a Common rail direct injection diesel engine. It evaluates the performance, combustion aspects, emission features at different injection pressures 210 bar to 240 bar intervals of 10 bar, along with 120 ppm of iron oxide nanoparticle. For this investigation, the B20 blend used as fuel contains 80% diesel and 20% biodiesel (Lotus seed Methyl Ester). The iron oxide nanoparticles were mixed with the fuel using a mechanical homogenizer and ultrasonication. The present work results revealed a reduction in FC by 12.5%, decreased CO by 50%, a decrease in HC by 16.88%, and the reduction of smoke density by 16.51% compared to that of baseline fuel maximum load (5.2 kW). The combined effect of 240 bar injection pressure and 120 ppm of iron oxide nanoparticle gives the best result. Abbreviation: MS; Motor Sprit (Petrol): HSD; High Speed Diesel: AFT; Transportation fuels: ICRA; Investment Information and Credit Rating Agency of India Limited: IONP; Iron Oxide Nano Particles: SFC; Specific Fuel Consumption: LSME; Lotus Seed Methyl Ester: MT; Metric Ton: BTE; Brake Thermal Efficiency: HC; Hydrocarbon: CO; Carbon monoxide: NOx; Nitrogen Oxides: HRR; Rate of Heat Release: BP; Brake Power
- 3 September 2016
- Published by Taylor & Francis in Biofuels
- Vol. 10 (5) , 583-589
Investigation of performance and emission characteristics of IC engine using sunflower oil methyl ester as fuel with oxygenated additive and EGR
This paper investigates the diesel engine performance and exhaust emissions with biodiesel as fuel and diethyl ether (DEE) as additive. Sunflower methyl ester was selected as a base fuel for the engine and DEE as an oxygenate with varying percentages. The experiment was conducted on a single-cylinder naturally aspirated direct-injection diesel engine with constant speed. Engine emissions are one of the major sources of pollution in the atmosphere. An approach to solve this problem is to add oxygenates to biodiesel. In this research work, an attempt has been made to analyze the effect of diethyl ether as an additive. Parameters such as brake thermal efficiency, brake specific fuel consumption and exhaust emission of CO, CO2, HC, NOx and smoke intensity were measured, and significant improvements were observed with the addition of diethyl ether with biodiesel as a blend. The brake thermal efficiency of biodiesel varied from 11.91 to 20.9%. NOx emission was reduced from 469 to 261 ppm in full load. Hydrocarbon (HC) varied from 200 to 130 ppm in full load. Similar variations were inferred for other emissions also.
- 3 September 2016
- Published by Taylor & Francis in Biofuels
- Vol. 10 (5) , 583-589
Investigation of performance and emission characteristics of IC engine using sunflower oil methyl ester as fuel with oxygenated additive and EGR
This paper investigates the diesel engine performance and exhaust emissions with biodiesel as fuel and diethyl ether (DEE) as additive. Sunflower methyl ester was selected as a base fuel for the engine and DEE as an oxygenate with varying percentages. The experiment was conducted on a single-cylinder naturally aspirated direct-injection diesel engine with constant speed. Engine emissions are one of the major sources of pollution in the atmosphere. An approach to solve this problem is to add oxygenates to biodiesel. In this research work, an attempt has been made to analyze the effect of diethyl ether as an additive. Parameters such as brake thermal efficiency, brake specific fuel consumption and exhaust emission of CO, CO2, HC, NOx and smoke intensity were measured, and significant improvements were observed with the addition of diethyl ether with biodiesel as a blend. The brake thermal efficiency of biodiesel varied from 11.91 to 20.9%. NOx emission was reduced from 469 to 261 ppm in full load. Hydrocarbon (HC) varied from 200 to 130 ppm in full load. Similar variations were inferred for other emissions also.
- 26 August 2016
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 38 (8) , 834-843
A comprehensive study on reduction of NOx emission applying EGR technique in a diesel engine using biodiesel (POME) as fuel with ether-based additives
The energy consumption is increasing rapidly due to population growth, improved living standards and industrialisation. A significant amount of fossil fuels is consumed by the transportation sector, which causes the fast depletion of fossil fuels and environmental pollution. These problems can be overcome by using Biodiesel. This research work aims to reduce the NOx emission in diesel engines. The literature survey reveals that the use of a fuel additive reduces the emissions by oxygenating the fuel. Among oxygenates, ether proves to behave better than alcohols. Hence, for this present work, two different types of ethers were selected which were not used in earlier occasions. DGME (Diethylene Glycol Monomethyl Ether) and DGMB (Diethylene Glycol Monobutyl Ether) are the two additives selected from the ether group and used as additives with palm oil methyl ester (POME) biodiesel in various proportions and tested in a direct injection compression ignition engine which reduced the emissions. To start with, the engine was run with diesel and subsequently with biodiesel and with the additives. The performance tests were carried out in a single-cylinder, four-stroke, water-cooled engine with and without exhaust gas recirculation (EGR). This engine is coupled with eddy current dynamometer. The use of biodiesel in conventional diesel engines results in substantial reduction in emission of carbon monoxide, particulates and unburned hydrocarbons, but increases NOx emission. This review focuses on reduction of NOx emission. Combustion and performance analysis of the engine have also been evaluated.
- 26 August 2016
- Published by Taylor & Francis in International Journal of Ambient Energy
- Vol. 38 (8) , 834-843
A comprehensive study on reduction of NOx emission applying EGR technique in a diesel engine using biodiesel (POME) as fuel with ether-based additives
The energy consumption is increasing rapidly due to population growth, improved living standards and industrialisation. A significant amount of fossil fuels is consumed by the transportation sector, which causes the fast depletion of fossil fuels and environmental pollution. These problems can be overcome by using Biodiesel. This research work aims to reduce the NOx emission in diesel engines. The literature survey reveals that the use of a fuel additive reduces the emissions by oxygenating the fuel. Among oxygenates, ether proves to behave better than alcohols. Hence, for this present work, two different types of ethers were selected which were not used in earlier occasions. DGME (Diethylene Glycol Monomethyl Ether) and DGMB (Diethylene Glycol Monobutyl Ether) are the two additives selected from the ether group and used as additives with palm oil methyl ester (POME) biodiesel in various proportions and tested in a direct injection compression ignition engine which reduced the emissions. To start with, the engine was run with diesel and subsequently with biodiesel and with the additives. The performance tests were carried out in a single-cylinder, four-stroke, water-cooled engine with and without exhaust gas recirculation (EGR). This engine is coupled with eddy current dynamometer. The use of biodiesel in conventional diesel engines results in substantial reduction in emission of carbon monoxide, particulates and unburned hydrocarbons, but increases NOx emission. This review focuses on reduction of NOx emission. Combustion and performance analysis of the engine have also been evaluated.
- 21 February 2013
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 35 (8) , 778-788
A Comparative Study of Performance and Emission Characteristics of Biodiesel Blends with Diethylene Glycol Dimethyl Ether as Additive
An experimental investigation was carried out to analyze the performance and emission characteristics of a compression ignition engine fueled with 20% biodiesel and 80% conventional diesel blended with diethylene glycol dimethyl ether on volume basis (0.2 to 0.6%). The performance test includes brake thermal efficiency and fuel consumption. The exhaust emission includes smoke density, CO, HC, CO2, and NOx. These parameters are evaluated in a single-cylinder diesel engine coupled with an eddy current dynamometer. The above factors in each case were compared with baseline data of mineral diesel and significant improvements have been observed.
- 21 February 2013
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 35 (8) , 778-788
A Comparative Study of Performance and Emission Characteristics of Biodiesel Blends with Diethylene Glycol Dimethyl Ether as Additive
An experimental investigation was carried out to analyze the performance and emission characteristics of a compression ignition engine fueled with 20% biodiesel and 80% conventional diesel blended with diethylene glycol dimethyl ether on volume basis (0.2 to 0.6%). The performance test includes brake thermal efficiency and fuel consumption. The exhaust emission includes smoke density, CO, HC, CO2, and NOx. These parameters are evaluated in a single-cylinder diesel engine coupled with an eddy current dynamometer. The above factors in each case were compared with baseline data of mineral diesel and significant improvements have been observed.
- 1 April 2012
- Published by Elsevier in Biomass and Bioenergy
- Vol. 39, 168-174
Performance and exhaust emission characteristics of a CI engine fueled with biodiesel (fish oil) with DEE as additive
- 1 April 2012
- Published by Elsevier in Biomass and Bioenergy
- Vol. 39, 168-174
Performance and exhaust emission characteristics of a CI engine fueled with biodiesel (fish oil) with DEE as additive
- 15 June 2009
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Reduction of NO X Emission Using EGR In Biodiesel Fueled Engine With Ether Based Additives
This project aims to reduce the NOx emission in the diesel engine exhaust and to improve the performance of the engine. The literary survey reveals that using fuel additives, which oxygenate the fuel, reduces the emissions. In these oxygenates, ethers behave better than alcohols. In this present work, some of these ethers were selected which were not much tried and details were not much known. Diethylene Glycol Mono Methyl Ether and Diethylene Glycol Monobutyl Ether are the two additives selected for this work. These additives are added with biodiesel (POME) in various proportions and it reduces the NOx emission. Initially, the engine was run by diesel, and then by biodiesel and biodiesel plus additives. The performance test was carried out in a single cylinder Kirloskar AV-I engine with and without EGR. This engine is coupled with electrical loading device. The use of biodiesel in conventional diesel engines results in substantial reduction in emission of unburned hydrocarbons, carbon monoxide and particulate. This review focuses on performance and emission of biodiesel in CI engines, and combustion analysis.
- 15 June 2009
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Reduction of NO X Emission Using EGR In Biodiesel Fueled Engine With Ether Based Additives
This project aims to reduce the NOx emission in the diesel engine exhaust and to improve the performance of the engine. The literary survey reveals that using fuel additives, which oxygenate the fuel, reduces the emissions. In these oxygenates, ethers behave better than alcohols. In this present work, some of these ethers were selected which were not much tried and details were not much known. Diethylene Glycol Mono Methyl Ether and Diethylene Glycol Monobutyl Ether are the two additives selected for this work. These additives are added with biodiesel (POME) in various proportions and it reduces the NOx emission. Initially, the engine was run by diesel, and then by biodiesel and biodiesel plus additives. The performance test was carried out in a single cylinder Kirloskar AV-I engine with and without EGR. This engine is coupled with electrical loading device. The use of biodiesel in conventional diesel engines results in substantial reduction in emission of unburned hydrocarbons, carbon monoxide and particulate. This review focuses on performance and emission of biodiesel in CI engines, and combustion analysis.