Mingwei Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mingwei Wang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Qingmin Chen
Roll Forging Research Institute, Jilin University, Changchun, China
3 shared publications - Xi Zhang
Shenyang Aircraft Corporation, Shenyang 110850, China
3 shared publications - Zhong-Yi Cai
College of Materials Science and Engineering, Jilin University, Changchun 130025, China
3 shared publications - Jiaxin Gao
College of Materials Science and Engineering, Jilin University, Changchun 130025, China
2 shared publications - Ya Zhang
College of Materials Science and Engineering, Jilin University, Changchun 130025, China
2 shared publications - Weiguang Zhang
College of Materials Science and Engineering, Jilin University, Changchun 130025, China
1 shared publication
Latest Publications
- Open Access
Numerical Simulation Analysis on Surface Quality of Aluminum Foam Sandwich Panel in Plastic Forming
The surface quality of an aluminum foam sandwich panel (AFSP) is very important for its appearance and application. This paper mainly studies the surface quality of AFSP after plastic forming. Combined with three-dimensional (3D) scanning technology, the normal deviation between the experimental AFSP and the target surface was obtained, and the surface quality parameters , and were calculated to evaluate surface quality. The AFSP models with cubic-spherical (CS) and tetrakaidecahedral (TKD) as foam structures were established respectively. A series of numerical simulations of multi-point forming (MPF) were then carried out. Equivalent strain and deformation characteristics of spherical and saddle-shaped AFSP were discussed. The main surface defects produced by AFSP in plastic forming, such as surface wrinkle, the local straight face effect and surface dimpling were analyzed. Finally, MPF experiments were carried out, and it was found that the numerical simulation results were significantly corresponded to the experimental AFSP in terms of the degree and distribution of normal deviation and surface quality evaluation parameters. The TKD model was more consistent with the experimental results than the CS model. Moreover, the results show that the surface quality can be improved by thicker face sheets and smaller core cell sizes.Open AccessNumerical Simulation Analysis on Surface Quality of Aluminum Foam Sandwich Panel in Plastic Forming
The surface quality of an aluminum foam sandwich panel (AFSP) is very important for its appearance and application. This paper mainly studies the surface quality of AFSP after plastic forming. Combined with three-dimensional (3D) scanning technology, the normal deviation between the experimental AFSP and the target surface was obtained, and the surface quality parameters , and were calculated to evaluate surface quality. The AFSP models with cubic-spherical (CS) and tetrakaidecahedral (TKD) as foam structures were established respectively. A series of numerical simulations of multi-point forming (MPF) were then carried out. Equivalent strain and deformation characteristics of spherical and saddle-shaped AFSP were discussed. The main surface defects produced by AFSP in plastic forming, such as surface wrinkle, the local straight face effect and surface dimpling were analyzed. Finally, MPF experiments were carried out, and it was found that the numerical simulation results were significantly corresponded to the experimental AFSP in terms of the degree and distribution of normal deviation and surface quality evaluation parameters. The TKD model was more consistent with the experimental results than the CS model. Moreover, the results show that the surface quality can be improved by thicker face sheets and smaller core cell sizes. - Open Access
Plastic Forming of Sandwich Panels and Numerical Analyses of the Forming Processes Based on Elastoplastic Equivalent Model
This paper studies the plastic forming of sandwich panels and proposes a universal elastoplastic equivalent method suitable for sandwich panels. To verify the generality of the equivalent method, according to the different core structures, the cores of bi-directional trapezoidal sandwich (BTS) panels and aluminum foam sandwich (AFS) panels are equated to orthotropic and isotropic (special orthotropic) single-layer panels respectively. Through the finite element (FE) numerical simulation of the mesoscopic model of the sandwich panel, the elastoplastic constitutive relationship of the equivalent core model is established, and then the macroscopic equivalent model of the sandwich panel is established. The FE numerical simulation of plastic forming was carried out for the mesoscopic model and equivalent model of BTS panel and AFS panel, and plastic forming experiments were conducted for the sandwich panel through a multi-point forming (MPF) test machine. The results show that the relative errors of the section average stress at the same position of the equivalent model and the mesoscopic model of sandwich panels are all within 4%; compared with the experimental results, the equivalent model of the sandwich panel has high forming accuracy and small shape error, which verifies the high accuracy and generality of the equivalent method. Moreover, using the sandwich panel equivalent model effectively reduces the calculation time of the numerical simulation.
Open AccessPlastic Forming of Sandwich Panels and Numerical Analyses of the Forming Processes Based on Elastoplastic Equivalent Model
This paper studies the plastic forming of sandwich panels and proposes a universal elastoplastic equivalent method suitable for sandwich panels. To verify the generality of the equivalent method, according to the different core structures, the cores of bi-directional trapezoidal sandwich (BTS) panels and aluminum foam sandwich (AFS) panels are equated to orthotropic and isotropic (special orthotropic) single-layer panels respectively. Through the finite element (FE) numerical simulation of the mesoscopic model of the sandwich panel, the elastoplastic constitutive relationship of the equivalent core model is established, and then the macroscopic equivalent model of the sandwich panel is established. The FE numerical simulation of plastic forming was carried out for the mesoscopic model and equivalent model of BTS panel and AFS panel, and plastic forming experiments were conducted for the sandwich panel through a multi-point forming (MPF) test machine. The results show that the relative errors of the section average stress at the same position of the equivalent model and the mesoscopic model of sandwich panels are all within 4%; compared with the experimental results, the equivalent model of the sandwich panel has high forming accuracy and small shape error, which verifies the high accuracy and generality of the equivalent method. Moreover, using the sandwich panel equivalent model effectively reduces the calculation time of the numerical simulation.
- Open Access
Numerical Study on the Plastic Forming of Doubly Curved Surfaces of Aluminum Foam Sandwich Panel Using 3D Voronoi Model
This paper presents a numerical investigation on the plastic forming of doubly curved surfaces of aluminum foam sandwich panel (AFSP). A mesoscopic 3D Voronoi model that can describe the structure of closed-cell aluminum foam relatively realistically was established, and a series of numerical simulations using the model of the sandwich panel with a Voronoi foam core were conducted on the plastic forming of two typical doubly curved surfaces including spherical and saddle-shaped surfaces of AFSPs to analyze the deformation behaviors and the forming defects in detail. Multi-point forming experiments of spherical and saddle-shaped AFSPs with different target radii were implemented and the doubly curved panels with good forming quality were obtained. The simulated results of the surface illumination maps, the face sheet profiles, and the maximum strain differences in selected areas of the face sheet and the experimental results indicated that the Voronoi AFSP model can reflect the actual defects occurred in the plastic forming of doubly curved sandwich panels, and the high forming accuracy of the sandwich panel model was also demonstrated in terms of the shape error and the thickness variation.
Open AccessNumerical Study on the Plastic Forming of Doubly Curved Surfaces of Aluminum Foam Sandwich Panel Using 3D Voronoi Model
This paper presents a numerical investigation on the plastic forming of doubly curved surfaces of aluminum foam sandwich panel (AFSP). A mesoscopic 3D Voronoi model that can describe the structure of closed-cell aluminum foam relatively realistically was established, and a series of numerical simulations using the model of the sandwich panel with a Voronoi foam core were conducted on the plastic forming of two typical doubly curved surfaces including spherical and saddle-shaped surfaces of AFSPs to analyze the deformation behaviors and the forming defects in detail. Multi-point forming experiments of spherical and saddle-shaped AFSPs with different target radii were implemented and the doubly curved panels with good forming quality were obtained. The simulated results of the surface illumination maps, the face sheet profiles, and the maximum strain differences in selected areas of the face sheet and the experimental results indicated that the Voronoi AFSP model can reflect the actual defects occurred in the plastic forming of doubly curved sandwich panels, and the high forming accuracy of the sandwich panel model was also demonstrated in terms of the shape error and the thickness variation.